• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.79-79
• /
• 2010

저온용 무연 솔더의 대표 조성으로 고려되고 있는 Sn-58Bi(융점: $138^{\circ}C$) 공정(eutectic) 조성은 우수한 강도에도 불구하고 연성(ductility) 측면에서의 문제점이 지속적으로 보고되고 있다. 따라서 이 합금계의 연성을 최대로 개선시킬 수 있으면서도 실제 상용화가 가능한 합금 조성의 개발 연구가 요청된다. 본 연구에서는 Sn-Bi 2원계 조성에서 최대의 연성을 나타내는 것으로 보고된 Sn-40Bi 조성에 미량의 합금원소를 첨가함으로써 최대의 연성을 확보하는 한편, 그 연성 특성이 변형속도에 어느 정도 민감한지를 인장 실험을 통해 결정하고자 하였다. 합금원소로는 0.1~0.5 wt%의 Ag, Mn, In, Cu를 선택하였으며, 인장 시편을 제조하여 $10^{-2}$, $10^{-3}$, $10^{-4}\;s^{-1}$의 3종류로 변형속도를 변형시켜가며 응력-변형 곡선(stress-strain curve)을 측정하였고, 조성별, 변형속도별로 최대인장강도(ultimate tensile stress, UTS) 및 연신율 결과들을 정리하였다. 합금원소를 첨가한 조성의 경우는 모든 시험 조건에서 Sn-40Bi보다 우수한 연신률을 나타내는 것으로 측정되었으나, $10^{-2}\;s^{-1}$의 빠른 변형속도에서는 그 향상 정도가 상대적으로 감소하는 경향이 관찰되었다. 특히 Sn-40Bi-0.5Ag 조성의 경우 느린 변형속도에서 특히 눈에 띄는 연신률 값을 나타내며, 모든 변형속도 조건에서 가장 우수한 연성을 나타내었다. 한편 Sn-40Bi-0.1Cu 조성의 경우 변형속도에 따른 연신률의 변화 정도, 즉, 변형속도에 따른 연신률의 민감도가 매우 커 $10^{-4}\;s^{-1}$ 속도에서는 Sn-40Bi-0.5Ag에 버금가는 연신률 값이 측정되었으나, $10^{-2}\;s^{-1}$ 속도에서는 가장 나쁜 연신률 특성을 보여주었다. Sn-40Bi-0.2Mn 조성은 최고의 연신률 향상 특성을 나타내지는 않았으나, In을 첨가한 경우보다는 대체적으로 우수한 연성을 나타내었다. 이상의 각 합금별 연성 특성은 인장시험 전의 미세조직 관찰 결과와 인장시험 후 파면부의 조직변화 관찰 결과로부터 해석되었다. 그 결과 석출상의 형성 여부, 인장 시험 중 재결정 조직의 형성 여부, 라멜라(lamellar) 조직의 분율과 라멜라 간격(lamellar spacing)의 정도 또는 $\beta$-Sn과 라멜라 조직 사이의 결정립계와 라멜라 조직 내 결정립계에서의 슬라이딩 모드(sliding mode) 변형 정도, 석출상의 크기와 분포 정도 등이 연신률 및 변형속도 민감도와 같은 연성 특성에 가장 큰 영향을 미치는 인자인 것으로 분석되었다.

• Journal of Korean Society of Steel Construction
• /
• v.14 no.3
• /
• pp.403-411
• /
• 2002

This paper described the ultimate strength and deformation limit of welded T-joints in cold-formed square hollow sections. Previous studies showed that the T-joint has an obvious peak load. with the failure mode of chord-web buckling at a ratio of branch width to chord width ($\beta$) of above 0.8. Similar to a T-joint with chord-flange failure mode, the strength at a certain deformation limit can be regarded as the ultimate strength of a T-joint Based on the experimental results including tests done by Kato and Zhao, the deformation limit was proposed as 3%B for $10.7{\leq}2{\gamma}(B/T){\leq}42.3$ and $0.8{\leq}{\beta}{\leq}1.0$. The strength formula of CIDECT and those of other researchers were also compared with the test results. Finally, the strength formula based on the column buckling was proposed.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.5
• /
• pp.141-148
• /
• 2021

In this study, the technology to prevent lateral deformation of steel dampers was reviewed and applied to the clamp type dampers. As for the experimental method, the rocking behavior was applied as in the previous study. The evaluation variables are the existing research results (SV-260) without lateral deformation prevention details and the test results (V-1, V-1R) with lateral deformation prevention details. Where, V-1 is the lateral deformation prevention detail at the lower part of the damper, and V-1R is the lateral deformation prevention detail at the lower part and upper part of the damper. As a result of evaluating the moment, drift ratio, and energy dissipation capacity relative to SV-260 at the time of maximum load, the maximum moments of V-1 and V-1R were increased by 1.22 times and 1.36 times compared to SV-260, and the maximum drift ratio increased by 2.41 times and 2.92 times. In addition, the energy dissipation capacity also increased by 1.39 times and 1.52 times, respectively. Therefore, the application of lateral deformation prevention details to the steel damper was evaluated as appropriate.

• Korean Journal of Optics and Photonics
• /
• v.8 no.1
• /
• pp.14-18
• /
• 1997

Using holographic interferometry, strain distributions for a cantilever beam subjected to the eccentric force can be analysed. Holographic fringe pattern shows inclined straight lines for the composite deformation of bending and torsion. Using these inclinations of the fringe pattern, 3rd order polynomial of plane displacements can be determined without difficulty. As the result, both of axial and shear strain distribution can be obtained from the second partial derivatives of this polynomial. These results agree well with FEM.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.44 no.3
• /
• pp.271-276
• /
• 2024

Traditional oil, a depleting resource, accounts for only one-third of the world's oil reserves, so research and cases of utilizing non-traditional oil as a resource are continuously increasing. However, unconventional oil contains bitumen containing solid particles such as sand, and because it is exposed to a high temperature and high pressure environment, deformation can frequently occur in oil pipelines. Therefore, variables such as material, thickness, and angle that can affect the deformation of the oil pipeline were derived and applied to the oil pipeline, and finite element analysis was performed using the Ansys program. As a result of finite element analysis, deformation and maximum load capacity were derived. Afterwards, the same analysis was performed by modeling an optimized oil pipeline by combining the factors with the best deformation resistance and maximum load capacity. As a result of the analysis, the effect of reducing deformation and increasing the maximum load capacity by about 30 % was confirmed, and factors for suppressing deformation when analyzing oil pipelines were derived.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.1
• /
• pp.401-408
• /
• 2019

This study numerically examined the maximum wind pressure distribution of a billboard on the roof of a middle-rise building. The deformation caused by the maximum wind pressure was examined. For the numerical analysis, the signboard was assumed to be installed on $(b)20m{\times}(d)10m{\times}(h)$ buildings. The maximum wind pressure was measured using four models with the standard model and different sizes of the signboard. The numerical analysis showed that the horizontal deformation predominantly occurs as the shape of the signboard becomes closer to a rectangle, and high wind pressure and deformation occur at the corners of both ends. As the height of the signboard increases, vertical deformation predominantly occurs, and static pressure forms on the backside. When the height is lower than the width of the signboard, the wind pressure is concentrated on the center of the roof. Therefore, the distribution of the maximum wind pressure is stable, and the effect of the wind pressure is relatively low as the height-to-width ratio approaches 1.

• Korean Journal of Materials Research
• /
• v.4 no.7
• /
• pp.837-844
• /
• 1994

To investigate that the theoretical formulas for extrusion forces are applicable to the manufacturing plant, the maximum extrusion forces were calculated from Siebel's and Geleji's formulas and also measured using 550 ton extrusion press. Parameters such as flow stress, $K_f$, angle of dead metal zone, $\alpha$ were obtained experimentally in order to calculate the maximum extrusion forces by the the theoretical formulas, and it was showed that the results were reliable as the deformation efficient factor, $\eta _f$ was determined to be less than 0.5. The maximum extrusion forces calculated from Siebel's formula and Geleji's formula for the angle of dead metal zone, $\alpha = 50^{\circ}$ were approached to the experimental results. However, it was found that Siebel's formula is more useful to apply to the manufacturing plant.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.2
• /
• pp.69-75
• /
• 2009

This study is analyzed by impact simulation according to material property at terminal case of hand phone. Maximum equivalent stress or strain at plastic is 40 times as great as that at magnesium alloy. And the next greatest stress or strain is shown at aluminium alloy. The value of maximum equivalent stress is shown as 6.5 Mpa in case of plastic, magnesium alloy and aluminium alloy. Maximum shear strain at plastic is 40 times as great as that at magnesium alloy. And the next greatest strain is shown at aluminium alloy. The value of deformation or strain at magnesium alloy and aluminium alloy is not different.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.18 no.1
• /
• pp.75-83
• /
• 2000

This paper deals with the application of two dimensional filtering technique for strain calculation using old and new geodetic data, and discusses the characteristics of general strain pattern in terms of seismic activity and tectonics. The mean rate of maximum shear strain is $0.12{\mu}/yr$. The mean direction of principal axes distribution of the compression is about $N80^{\circ}E$.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.8
• /
• pp.5-14
• /
• 2013

Coarse granular geomaterials containing large gravels are broadly used for construction of large geotechnical systems such as dams, levees, railways and backfills. It is necessary to evaluate deformation characteristics of these materials for dynamic analysis, e.g. seismic design. This study presents evaluation of dynamic deformation characteristics of coarse materials using large scale resonant column testing apparatus, which uses specimens with 200 mm in diameter and 400 mm in height, and the effects of gradation characteristics on maximum shear modulus, shear modulus reduction curve and damping characteristics were investigated. From experimental study using rock-fill materials for a dam, we could see that the largest or mean particle size affects the shape of shear modulus reduction curve. When the specimens are prepared under the same conditions for maximum particle size, the coefficient of uniformity affects the confining stress exponent of maximum shear modulus. It could be concluded that the maximum particle size is an factor which affects shear modulus reduction curve, and that the coefficient of uniformity is for small strain shear modulus, especially for the sensitivity to confining stress.