• Progress in Superconductivity and Cryogenics
• /
• v.4 no.1
• /
• pp.84-88
• /
• 2002

The resistive fault current limiter (SFCL) is a very attractive device for power networks. But it has a serious Problem in using YBCO films for fault current limiter is inhomogeneities caused by imperpect manufacturing. So simultaneous quenches are a difficult problem which elements for current limiting are connected in series for increasing voltage ratings. We investigated extended electric field-current characteristics for current limiting element of YBCO film when O-130mT magnetic field is applied. And quench characteristics were investigated in over all element and between elements of YBCO films. From the experiments, it was shown that applied magnetic fields using solenoid coil induced uniform quench distribution for over all stripes and simultaneous quench in all elements for current limiting of YBCO film was realized. We have achieved resistive fault current limiter of 1.2kV/20A rating using magnetic field.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.10a
• /
• pp.27-29
• /
• 2003

Solution-based MOD-TFA deposition technology of YBCO layers offers a route to low-cost YBCO coated conductors. Since the structures and properties of grown thin film by MOD process are strongly influenced by chemistry of precursor solution, the chemical modification of precursor solution for MOD process are important for improvement of the electrical properties of YBCO films. In this study, the precursor solution for MOD process are modified by chemical additives and solvents. The microstructure and texture of YBCO films grown by chemically modified precursor solution were characterized with SEM/EDS, XRD.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.10a
• /
• pp.79-82
• /
• 2003

We prepared YBCO coated conductor by direct deposition of YBCO on Ag substrate by a MOCVD method. The Ag substrate was only prepared by cold rolling. The XRD data of the as-rolled Ag tape showed the formation of dominant (420) oriented grains. Processing variables were the oxygen partial pressure (Po$_2$) and deposition temperature (T$_{d}$). It was found that the a-axis oriented films were grown at lower T$_{d}$ below 80$0^{\circ}C$, while the c-axis oriented films were grown about 80$0^{\circ}C$. The surface of the films consisted of a second inclusion phase dispersed in the YBCO matrix. The Cu-rich phase regions were observed at the YBCO/Ag interface probably due to the inter-diffusion of Ag and Cu. Cu.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.531-534
• /
• 2004

초전도 coated conductor는 보호층/초전도층/완충층/금속기판의 구조를 가지며 완충층은 다층산화물 박막으로 이루어져 있다. 본 연구에서는 니켈 기판의 원자가 초전도층으로 확산 침투하는 것을 방지하는 YSZ(Yttria Stabilized Zirconia) 박막의 증착방법 및 최적조건에 대하여 소개하고자 한다. 금속타겟을 사용하며 산화반응가스로서 수증기를 사용하는 것을 특징으로 하는 DC reactive sputtering을 이용하여 YSZ를 증착하였으며 기판 온도는 $850^{\circ}C$ 이며 증착시 수증기 분압은 1mTorr이었다. YSZ의 최적두께를 알아보기 위하여 $CeO_2(12.2nm)/Ni$ 상부에 130nm, 260nm, 390nm, 650nm로 두께를 달리하여 YSZ층을 증착하고 SEM으로 박막 표면상태를 관찰한 결과 columnar grain growth를 하며 두께가 두꺼워 질수록 표면조도가 증가함을 알 수 있었다. 4개의 각 시료위에 thermal evaporation 증착법을 이용하여 $CeO_2$를 18.3nm의 두께로 증착한 후 PLD를 이용하여 YBCO 초전도 박막을 300nm 두께로 증착하였고 77K, 0T에서 임계전류가 각각 0, 6A, 7.5A, 5A로 측정되었다. 이는 YSZ층의 두께가 두꺼워질수록 기판 구성원자의 확산방지역할을 충실히 하는 반면에 표면조도는 증가함을 알 수 있었다.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.02a
• /
• pp.88-91
• /
• 2003

The crystal structure and properties of YBa$_2$Cu$_3$$O_{7-x}$(YBCO) and CeO$_2$ thin films deposited on r-plane (1(equation omitted)02) sapphire substrate by pulsed- laser deposition(PLD) have been investigated. C-axis oriented epitaxial YBCO thin films with critical temperature (Tc) of 88 K were routinely grown on (200) oriented CeO$_2$ buffer layers with thickness in the range between 20 to 80 nm. When the thickness of the (200)oriented CeO$_2$ buffer layer increases over than 80 nm, the superconducting properties of YBCO thin films on that were deteriorated. The decrease in Tc of YBCO thin films was explained by the microcrack formation in CeO$_2$ buffer layer. These results indicate that the thickness of the (200) oriented CeO$_2$ buffer layer is critical to the epitaxial YBCO thin nim growth on r-plane (1(equation omitted)02) sapphire substrate.e.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.368-370
• /
• 2002

We present current limiting properties of 1.2kV/70A superconducting fault current limiter based on YBCO thin films. This is consisted of 6 wafers (3 parallel $\times$ 2 serial connection) with 4 inch-diameter YBCO thin film. The quench current Iq of the switching elements vary between 33.9 and 35.6 A. Within the difference of 0.5 A in the sum of quench current Iq in two stacks, the serial connection of the stacks showed the simultaneous quench behavior in applied power of 1.2 kV/70A.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.43-43
• /
• 2010

HTS(High Temperature Superconductor) cable has a high possibility of practical use due to the possibility of low voltage and high capacity transmission caused by its lower power loss than copper cable. On the other hand, when fault current occurred, resistance increase caused by superconductivity loss, the amount of power supplies has diminished, furthermore, it's necessary to take the possible danger of damage to HITS cable into account. Therefore, an effective plan for dealing with the above problem is to link HITS cable to SFCL. In this study, we researched the possibilities of normal transport current as well as the safety of HITS cable by analyzing the properties of transport current in HITS cable connected with SFCL.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.41-44
• /
• 1998

Dual mode resonators were fabricated using high temperature superconductor. The deposited material was $Y_1Ba_2Cu_3O_{7-x}$(YBCO) on MgO(100) substrate using pulsed laser deposition. Dual mode resonators were patterned by standard photolithography process and wet etching. At the back-side of the substrate, the ground plane with the metal layer of Ti and Ag was fabricated. The transition temperatures of YBCO films were 85-88 K, and network analyzer was used for testing the performance of the resonators. The input/output feedline angles of each resonator were $60^{\circ}$and $100^{\circ}$. The resonant frequency of resonators was 10 GHz. In this paper, dual mode resonator was fabricated for the application of satellite communication.

• Progress in Superconductivity and Cryogenics
• /
• v.10 no.1
• /
• pp.10-14
• /
• 2008

Differently from BSCCO tapes which are fabricated by powder-in-tube method, the coated conductors are made by the evaporation of YBCO on metal substrate. Due to this structural merit, although the coated conductors are generally used for large current transportation, they are expected to be favorable to the purpose of the fault current limitation as well. In this study, using YBCO coated conductor having copper stabilizer formed by plating technique(produced by Superpower Co.), we investigated the over-current characteristics of the coated conductor. The coated conductors had 85 A $I_c$ and 90 K $T_c$. The resistance of the conductor was 0.93 $m{\Omega}/cm$ at 300 K and 0.17 $m{\Omega}/cm$ at the temperature right above $T_c$. To the coated conductors, we applied the voltages of the range from 150 $V_{rms}$ to 230 $V_{rms}$ and measured the V-I curves using four probe method. From the results, we could analyze the electric behavior of the coated conductor in flux flow state. As the current exceed $I_c$, the currents were distributed into the superconductor and metal stabilizer. The amounts of the currents shared through both current paths were calculated under the assumption that the ,Joule heating was perfectly eliminated by $LN_2$ surrounding the conductor. Finally, the condition for the stable current flowing state which does not affect the conductor was established from the analysis on the over-current characteristics.

• Progress in Superconductivity
• /
• v.6 no.2
• /
• pp.113-117
• /
• 2005

In this study, electromagnetic analysis of current paths including meander pattern, spiral pattern, and bi-spiral pattern were performed and in order to verity the analysis results, experiments tests including quench test, and insulation tests were performed. In addition, bubble corner concepts were introduced to enhance insulation reliability. From our study, bi-spiral pattern of YBCO thin films were rather effective for quench and insulation than the other patterns. So this current path pattern was adopted for YBCO thin films in order to develop 6.6 kV resistive fault current limiters. Finally YBCO thin films were connected in series and parallel to enhance capacity, and the test results of current limiting characteristics of 6.6kV resistive SFCL were successful. The Progress in Superconductivity is published every six month and serves as a channel for publications on superconductivity and related topics. The author(s) are required to submit THREE copies of the manuscripts along with original figures directly to the Editor.