• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.6A
• /
• pp.819-825
• /
• 2008

This paper describes the shaping formation and the erection of SCST structure by cable-tensioning. It could be a fast and economical method for constructing the space structure consisted with uniform pyramids by cable-tensioning of the cable in bottom chords. In the initial layout, the top chords and web members are left at their true length, the bottom chords are given gaps in proportion to the desired final shape. The feasibility of the proposed shaping method and the reliability of the established geometric model were confirmed with nonlinear finite element analysis and an experimental investigation on small scale and full size test models. As a result, the behaviour characteristic of MERO joint is very significant in shaping analysis of space structure. This study suggests the most reasonable modeling technique for the prediction of shaping in practices. And it is shown the characteristic of the behavior in shaping test for practical design purposes.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.716-716
• /
• 2012

최근 항만구조물을 설계함에 있어 대수심 및 고파랑 지역에 설치되는 외곽시설의 상당수는 직립식 케이슨 혼성제 단면을 채택하고 있다. 이는 상대적으로 수심이 깊고, 설계파와 같은 외력 조건이 크기 때문에 경사제에 비하여 경제성 및 시공성이 유리하기 때문으로 판단된다. 그렇지만 아직까지 소규모 항만 및 어항시설에 있어 경사제를 채택하고 있다. 본 연구에서는 이와 같은 경사식 구조물을 설계함에 있어 월파에 의한 방파제 배후 경사면에 피복된 피복재의 안정성을 검토하며, 실험사례를 통하여 최적 설계안 및 설계방향을 제시하고자 한다. 경사식 구조물 배후 사면 피복재의 안정 중량에 대해서는 우리나라의 항만 구조물의 설계기준(항만 및 어항설계기준, 2005) 뿐만 아니라 국외의 설계기준(CEM, Coastal engineering manual, 2005 등)에서도 아직까지 설계법을 제시하고 있지 않고 있다. 본 연구에서 수행한 단면 수리모형실험에서는 1/50의 실험축척을 적용하여 대상 외곽 구조물에 대하여 수리특성과 안정성을 검토하였다. 특히 경사제 배후의 안정성 확보를 위하려 동일 구간에 대하여 설계파 조건 등을 중심으로 총 9개의 실험안을 설정하여 안정성을 검토하였다. 아래 그림은 이중 초기 설계안과 최종적으로 제안된 제시안에 대한 완성모형, 실험장면 및 결과이다. 일반적으로 접안시설과 외곽시설이 어느 정도 이격되어 있어 적정량의 월파를 허용할 수 있는 경우 상치콘크리트의 형상 및 마루높이을 변경하여 월파의 낙하 및 도달거리를 배후면의 안정성을 확보할 수 있을 정도로 유도함으로써 안정적인 구조물 설계가 가능할 것으로 판단된다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.3
• /
• pp.347-353
• /
• 2012

Recently, multi-functionalization (as in smart phones) has been in demand, and the connectors connecting the electrical signals of each board in a cellular phone have become key components. The miniaturization of these connectors is required to achieve a finer pitch design and enhance the electrical signal transfer capacity. However, the miniaturization of connectors reduces the structural safety, and a finer pitch design may cause contact problems under external impact. In this paper, a preliminary design for miniaturized, finer-pitch connectors is suggested for a product with 50 pins and a thickness of 0.2 mm. The assembly process of the FPCB (Flexible Printed Circuit Board) and connector was simulated to ensure the holding force between the two components and avoid overstressing. The design optimization process was performed with the Taguchi method. Fatigue analysis was also conducted to predict the fatigue life of the terminal, and the theoretical and experimental results were compared.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.10 no.3
• /
• pp.7-17
• /
• 1990

The objective of this paper is to provide a method of optimizing are as of the members as well as shape of both truss and arch structures. The design process includes satisfaction of stress and Euler buckling stress constraints for truss and combined stress constraints for arch structures. In order to reduce the number of detailed finite element analysis, the Force Approximation Method is used. A finite element analysis of the initial structure is performed and the gradients of the member end forces are calculated with respect to the areas and nodal coordinates. The gradients are used to form an approximate structural analysis based on first order Taylor series expansions of the member end forces. Using move limits, a numerical optimizer minimizes the volume of the structure with information from the approximate structural analysis. Numerical examples are performed and compared with other methods to demonstrate the efficiency and reliability of the Force Approximation Method for shape optimization. It is shown that the number of finite element analysis is greatly reduced and that it leads to a highly efficient method of shape optimization of structures.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.2 no.2
• /
• pp.1-5
• /
• 2001

One of the major advantages of using engineering plastics is ease of part assembly through a locking mechanism known as a snap fit. The typical snap fit involves a short cantilever beam with a projection at the free end. which slides over a one way ramp on the mating part to lock in place. The tightness of the mechanism is determined by the lateral interference of the two sliding members If too small they become loose and can't hold together. while if too large. excessive force can be generated. causing failure of the cantilever beam during the assembly operation. Therefore. the accurate determination of the force-deflection relationship for cantilever beams is a key element in snap fit design. And also. the process of injection molding should be considered when cantilever beam is designed. But it is not easy for novice designers to design them appropriately because of the profound knowledge related to injection molding. In this paper. an intelligent design program has been developed and proposed to improve a conventional empirical design method.

• Korean Journal of Optics and Photonics
• /
• v.21 no.5
• /
• pp.214-223
• /
• 2010

Optimization of a 30 cm lightweight mirror was proposed with the best optical performance under various loads of gravity and thermal loads with proper boundary conditions. A pattern for a lightweight mirror was generated based on the best optical performance combined with ease of manufacturing for proper design parameters of physical properties of face sheet, back sheet, rib, and web. Evaluation of the optical performances of a telescope mirror was obtained by using the finite element analysis program, NX I-DEAS. Surface errors, individual aberration terms, such as piston, tilts, focus and other aberrations were calculated by using Zernike polynomials. The proposed telescope mirror meets well the opto-mechanical design consideration of RMS surface error less than 16 nm.

• Design Convergence Study
• /
• v.15 no.2
• /
• pp.169-184
• /
• 2016

Using geospatial information in the early design phase is crucial because it requires considerable time, money, and effort. We use VWorld, part of the National Spatial Information Distribution system provided by the Korean Ministry of Land, Infrastructure and Transportation, for providing geospatial information to building designers. We provide methods to adopt VWorld geospatial information to building design and develop plugins for a BIM authoring tool to transform and construct necessary BIM data in a user-friendly format. BIM users are benefitted from extra design information supplied from sibling disciplines such as urban design. GIS users are benefited by feedback building information continuously supplied from building projects based upon standard GIS coordinates. It is clear that an architectural designer with BIM tool can save time and efforts to obtain the geospatial information related a project using the developed system as result of this research.

• Computational Structural Engineering
• /
• v.7 no.2
• /
• pp.4-10
• /
• 1994

컴퓨터 성능과 전산유체역학 분야는 지속적으로 발전하고 있으므로 이에 따라 유체의 유동장은 더욱 정확하고 상세히 묘사할 수 있게 될 것이며, 더불어 ALE유한요소법 등과 같은 유체-구조 상호작용해석 기법이 발전해 나갈 것이다. 따라서, 현재 수행되고 있는 풍동실험은 다양한 모형제작으로 인한 비용문제와 완성된 모형의 정밀도 문제, 각 모형에 대한 반복적인 실험과정 등 적절한 설계형상을 선택하는 과정에서 효율성이 낮은 경우가 많으므로 수치해석에 의한 내풍안정성 평가과정을 병행함으로써 실험의 효율성이 낮은 부분을 보완, 최소화할 수 있을 것이다. 특히 적은 비용 및 시간내에 개략적인 내풍안정성 파악이 요구되는 개념설계 및 초기설계단계에 근사적인 내풍안정성 검토 기술로서 결과적으로 활용될 수 있을 것이다. 또한 수치해석기법의 가장 큰 장애요인었던 유체 유동장의 모사정도가 향상됨에 따라 수치해석에 의한 장대구조물의 내풍안정성해석은 앞으로 상당한 발전이 있을 것으로 전망된다.

• Journal of Korean Society of Steel Construction
• /
• v.13 no.2
• /
• pp.191-200
• /
• 2001

This paper presents buckling analysis of the cylindrical shell subjected to axial loads using numerical method. The modeling method, appropriate element type, and number of element are recommended by comparing with analytical solution. Based on the parametric study, buckling stress decreases significantly as the diameter-thickness ratio increases. These results are different from those obtained from buckling analysis of columns. The number of buckling half-wave in circumferential direction decreases as the diameter-height ratio increases. Buckling stress increases 1~2% as the thickness of base plate increases. Therefore the effect of base plate on buckling strength for cylindrical shell can be disregarded. Buckling stress significantly decreases as the amplitude of initial geometric imperfection used for calculating buckling stress is developed and it shows a good agreement with numerical results.

• Tribology and Lubricants
• /
• v.1 no.1
• /
• pp.20-29
• /
• 1985

많은 윤활 부품의 성능과 수명은 초기작동기간에 금속표면에서 일어나는 현상들에 의하여 좌우된다. 특히 혼합마착구역(Mixed film region)에서나 윤활막의 두께가 몇십 마이크론의 정도가 되는 EHD(Elastohydrohynamic)윤활구역에서 작동하는 경우엔 더욱 중요하다. 이러한 경험적 현상에 의해 상대운동하는 두마찰면의 초기 작동과정을 길들이기(run-in, breaking-in)라고 부르고 "마찰 부분의 형상이나 마모 및 윤활 마찰특성이 향상되어가는 과정" 으로 정의한다. 보통 길들이기 과정이 끝나면 표면 모양은 더이상 변하지 않고 마모나 마찰 특성이 일정하게되며 이 단계를 정상 상태라고 부른다. 길들이기과정이 중요시되는 것은 이 과정에서 마모는 정상 상태보다 심하고 Scuffing 혹은 Scoring현상이라고 부르는 마찰면 손상의 가능성이 항상 존재하기 때문이다. 이 현상은 보통의 마모나 부식 또는 피로파손의 형태와는 달리 갑작스런 발생으로 부품이나 기관의 부분적 혹은 완전 파손을 유발함으로써 설계나 제조 과정에 문제를 제기하는 요인으로 오래전부터 알려져 왔다.부터 알려져 왔다.