• Journal of the Korean GEO-environmental Society
• /
• v.9 no.1
• /
• pp.27-31
• /
• 2008

In this study, evaluation of samples' reflection of in-situ condition was performed for those by 225 mm KICT large sampler and NX size piston sampler. Disturbance analysis was conducted for the clay sampled by two kinds of sampler throughout consolidation tests, uniaxial tests and triaxial test, under the same condition. From the analysis it can be seen that not only the initial void ratio and preconsolidation pressure from KICT large sampler but strength parameters from both uniaxial and triaxial compression tests are also about 10% higher than those of NX size piston sampler's.

• Journal of the Korea Concrete Institute
• /
• v.27 no.5
• /
• pp.569-577
• /
• 2015

The aim of this study is to qualitatively evaluate the cracking control effects of expansive concrete used in reinforced concrete building. The result of experiments in laboratory shows that autogenous shrinkage and drying shrinkage are suppressed by using expansive additive. The tensile stress-strength ratio is lower in expansive concrete than normal concrete under fully restrained condition. Compression stress could be effectively generated in early age in the walls in buildings by the use of expansive additive, and tensile stress due to drying shrinkage at later age eventually decreased. Additionally, visual observation at long-term ages shows that the cracking area of expansive concrete was approximately 35% of normal concrete, which confirms that the use of expansive additive reduces concrete cracking in reinforced concrete buildings.

• Journal of Advanced Marine Engineering and Technology
• /
• v.18 no.3
• /
• pp.52-62
• /
• 1994

기계나 구조물 파괴의 대부분은 노치부를 기점으로 하여 발생하기 때문에 첨단복합재료를 노지부 재로서 안전하면서도 경제적으로 사용하기 위해서는 각종 조건하에 있어서 강도특성을 명확히 하는 것은 대단히 중요하다. 본 연구에서는 노치를 갖는 복합재료를 이용하여 각종조건하에서 강도특성평가실험을 행하였으 며, 얻어진 결과를 종합하면 다음과 같다. (1) 첨단복합재료 노치재는 試驗片의 幾可學的 形狀과는 관계없이 노치반경 p만에 의해 결정되는 최대탄성응력 $\sigma_{max}$일정의 條件下에서 破t짧된다. (2) 破斷時 최소단면에서의 공칭응력 $\sigma_{c}$와 응력집중계수 $K_{t}$와의 관계에 있어서,$\sigma_{c}$의 값이 $K_{t}$의 증대와 더불어 떨어지고 있는 부분과, $K_{t}$와 관계없이 거의 일정하게 되고 있는 부분으로 나누어지는 現象은 노치재의 回轉굽힘 또는 인장압축파열에서 보여지는 현상과 外觀上 對應하고 있다. 즉, 정적파괴와 피로파괴는 파괴의 양상이 비슷하다 (3) PEN수지단체의 경우, 피로균열발생은 점발생적 피로균열이 최대탄성응력에 의해 지배되며, 노치에 만감하며,균열전파수명은전수명에 비해 상당히 짧다. (4) 단탄소섬유강화복합재료의 경우, 피로균열은 섬유端에 응력이 집중하기 때문에 일반적으로 섬유端에서 아주 빠른 시기에 발생하지만, 섬유가 피로균열진전에 대해 방해물로 작용하기때문에 아주 천천히 전파한다. (5) 短탄소鐵維는 피로균열발생에 대해서는 負의 강화작용 전수명의 극히 초기단계에 피로균열 발생을, 피로균열전파에 대해서는 正의 강화작용을 한다. (6) 단탄소섬유를 PEN에 강화함으로 인해 정적강도 보다 피로강도에 더 큰 강화효과를 초래했으며, 선형노치역학의 개녀은 첨단 복합재료의 강도평가에 대단히 유효했다.

• Journal of Korean Society of Steel Construction
• /
• v.19 no.6
• /
• pp.725-735
• /
• 2007

The local buckling strength and post-local buckling strength of thin steel plates in the steel-concrete composite column were evaluated by nonlinear finite element analyses. The proposed width-to-thickness limit ratio was based on elastic buckling analyses, in which the increased local buckling capacity of the plate due to the in-filled concrete was considered by the boundary conditions of the thin plate. Considering the initial imperfections and residual stresses, we determined the initial local buckling strength and post-local buckling strength of the thin plates with various width-to-thickness ratios. The formula to evaluate the compressive capacity of the steel-concrete composite column based on the effective width of the plate was proposed. For verification, values determined by the formula were compared with the experimental results.

• The Journal of Engineering Geology
• /
• v.17 no.1 s.50
• /
• pp.27-40
• /
• 2007

Stratigraphy has been renewedly set up and the evolution of tectonic events related to basin formation has been exam-ined on the basis of fault-slip data analysis in the Tertiary Eoil and Waeup basins of the southeastern part of Korea. First of all, field mapping was carried out in detail for Tertiary formations and then paleostress analysis were peformed with more than 400 fault slip data collected from 11 sites in the Tertiary formations and the Yucheon Group. It is judged that both the Eoil and Waeup basins filled up with Tertiary deposits might be simultaneously formed in separate locations. The Janggi Group in the Eoil basin is divided into following stratigraphic units in ascending order: Gampo Conglomerte, Hongdeok Basalt, Nodongri Conglomerate and Yeondang Basalt, and the Bomkori Group in the Waeup basin: Waeupri Tuff; Andongri Conglomerate, Yongdongri Tuff and Hoamri Volcanic Breccia. Paleostress analysis by using striated faults reveals five sequential tectonic events: (1) NW-SE transtension (event I), (2) NW-SE transpression (event IIl), (3) NE-SW pure extension (event III), (4) N-S transpression (event IV) and (5) E-W pure compression (event V). Therefore, five sequential tectonic movements are closely associated with the formation and evolution of the Tertiary basins in the study area: tectonic event I of NW-SE extension is related to formation of the Tertiary basins during the late Oligocene to the Early Miocene, tectonic events II, III and IV caused the termination of the Tertiary basin opening and the crustal uplift in the study area, and tectonic event V upheaved the east coast or Korean Peninsula with compressive stress due to intense subduction of the Pacific plate into Asian continent since the Early Pliocene.

• Journal of Korean Society of Steel Construction
• /
• v.11 no.3 s.40
• /
• pp.271-279
• /
• 1999

Recently, studies on semi-rigid beam-to-column connections have been done to develop a T-stub element with separators between column face and T-stub flange. In this paper, inelastic analyses for the improved T-stub element are performed, and their results are compared with existing experimental results. The inelastic analyses using gap elements between column face and the separator, and initial stresses at the high-tension bolts result in good agreement with experimental results. Simplified design methods estimating the initial stiffness and the strength of the semi-rigid connection for compression force are proposed.

• Journal of the Korea Concrete Institute
• /
• v.13 no.2
• /
• pp.139-145
• /
• 2001

One of ways to make high-strength concrete is for the mix contain particles graded down to the finest size : this is achieved by the use of fly ash, silica fume which fills the spaces between the cement particle and between the aggregate and the cement particles. And, the mix needs a sufficient workability. This is achieved by the use of a superplasticizer. This study is to investigate frost resistance of high-strength concrete at early age, with ratio of tensile strength and recovery of compressive strength, when high-strength concrete is placed in cold climates. According to this study, it is necessary to ensure 4 % of air content, 5 kgf/$\textrm{cm}^2$ of tensile strength, at least, for frost resistance of high-strength concrete at early age.

• Journal of the Korea Concrete Institute
• /
• v.22 no.4
• /
• pp.481-488
• /
• 2010

Since existing constitutive models developed for confined normal strength concrete overestimate ductility when they are applied to confined high strength concrete, these models cannot be directly applied to confined high strength concrete. In an effort to solve this problem, an accurate stress-strain relationship of the hihg strength concrete needs to be formulated by examining the confinement effects due to increase of the concrete strength. In this study, a constitutive model is developed to express the stress-strain relationship of confined high strength concrete by carrying out regression analysis of the main parameters affection strength and ductile behavior of reinforced high strength concrete columns. Twenty-five test specimens were chosen from the reported experimental studies in the literature. The experimental results of stress-strain relationships of show a good agreement with results of the stress-strain relationships of suggested high strength concrete, covering a strength range between 60 and 124 MPa.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.2
• /
• pp.103-113
• /
• 2000

기존의 Terzaghi 압밀이론은 상대적으로 연약토층이 두껍지 않고, 초기함수비가 낮으며 적은 유효응력의 증가가 예상되는 곳에 그 적용이 제한되어 있었다. 그 이유는 Therzaghi 압미이론 자체가 미소변형률과 선형적인 압축성 및 투수성등을 기본적인 가정사항으로 내포하고 있기 때문이다. 이러한 가정사항을 극복하고자 Gibson et al. 은 일차원 비선형 유한 변형률 압밀이론에 관한 엄밀해를 제시하였다. 이 이론은 기존의 많은 가정사항들을 극복하여 실제 현상에 더욱 부합하는 예측을 할 수 있는 장점이 있는 반면, 비선형적인 응력-변형 관계, 변형-투수계수 관계의 도입과 좌표변환 및 현장의 시고이력을 그대로 적용하는데 많은 어려움이 있는 것이 사실이다. 본 연구에서는 이러한 비선형 유한형태를 압밀이론을 이용한 압밀현상 예측을 위하여, 비선형적인 응력-변형 관계, 변형-투수계수 관계에 관한 함수식을 구성하고 이를 포함하는 컴퓨터 프로그램을 개발하였다. 개발 프로그램은 많은 폼과 모듈로 구성되어 있는데, 이러한 각각의 폼과 모듈은 GUI 기능의 극대화를 통해 복잡한 이론에 익숙하지 않은 실무자들이 쉽게 본 이론을 이용할 수 있도록 설계 되었다. 또한 개발프로그램은 다양한 하중단계 및 비선형적인 응력-변형 관계, 변형-투수계수 관계에 관한 회귀분석, 각 유효응력 단계별 상이한 비선형 계수 g와 λ를 적용할 수 있으며, 계산을 위한 전처리과정은 물론 계산된 결과를 위한 다양한 후처리과정이 모두 사용자 위주의 GUI 기능을 충분히 갖도록 설계되었다. 개발 프로그램의 검증을 위하여 실제 현장의 계측자료 및 기존 연구문헌상의 결과와 본 개발 프로그램의 예측결과를 비교.분석하였으며, 다양한 간극비 상태의 비선형 계수가 해석결과에 미치는 영향을 알아보았다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.6
• /
• pp.193-198
• /
• 2021

In this study, the rheological characteristics and of 3D printing composite materials and the compressive strength characteristics according to the lamination patterns were evaluated. As a result of rheology test, rapid material change was observed after 60 minutes of extrusion, yielding stress 1.4 times higher than immediately after mixing, and plastic viscosity was 14.94-25.62% lower. The compressive strength of the specimens manufactured in the mold and the laminated specimens were compared, and the lamination pattern of the laminated specimens were 0°, 45°, and 90° as variables. The compressive strength of the mold casting specimen and the laminated specimen from 1 to 28 days of age showed similar performance regardless of the lamination pattern. In particular, at the age of 28 days, the modulus of elasticity, maximum compressive strength, and strain at maximum stress of all specimens were almost the same. In order to analyze the interface of the laminated specimens, X-ray CT analysis of the specimen whose compressive strength were measured was performed. Through CT analysis, it was confirmed that cracks did not occur at the lamination interface, which can be judged that the interface in the laminated specimen behaved in an integrated manner.