• Korean Chemical Engineering Research
• /
• v.61 no.1
• /
• pp.39-44
• /
• 2023

In this study, the particle size of Si polycrystals was controlled through wet-sedimentation method, and changes in the capacity and cyclic characteristics of the Si anode material according to the particle size were observed. After wet-sedimentation of Si particles pulverized by a vibration mill, the non-uniform particle distribution of Si was uniformly controlled. The d₅₀ of a sample in which Si was sedimented for 24 hours decreased to 0.50 ㎛. As a result of the electrochemical characteristic analysis, the Rct value representing the resistance in the electrode was significantly reduced due to the decrease in particle size. The unclassified Si sample exhibited a discharge capacity of 2,869 mAh/g in the first cycle, and decreased to 85.7 mAh/g after 100 cycles. The sample in which Si was classified for 24 hours showed a capacity of 3,394 mAh/g initially, and maintained a capacity of 1,726 mAh/g after 100 cycles. As the size of the Si particles decreased, the discharge capacity increased and the cycle life was also increased.

• Journal of Bio-Environment Control
• /
• v.32 no.1
• /
• pp.48-56
• /
• 2023

High-pressure sodium (HPS) lamps have been widely used as a useful supplemental light source to emit sufficient photosynthetically active radiation and provide a radiant heat, which contribute the heat requirement in greenhouses. The objective of this study to analyze the thermal characteristics of HPS lamp and thermal behavior in supplemented greenhouse, and evaluate the performance of a horizontal leaf temperature of sweet pepper plants using computational fluid dynamics (CFD) simulation. We simulated horizontal leaf temperature on upper canopy according to three growth stage scenarios, which represented 1.0, 1.6, and 2.2 plant height, respectively. We also measured vertical leaf and air temperature accompanied by heat generation of HPS lamps. There was large leaf to air temperature differential due to non-uniformity in temperature. In our numerical calculation, thermal energy of HPS lamps contributed of 50.1% the total heat requirement on Dec. 2022. The CFD model was validated by comparing measured and simulated data at the same operating condition. Mean absolute error and root mean square error were below 0.5, which means the CFD simulation values were highly accurate. Our result about vertical leaf and air temperature can be used in decision making for efficient thermal energy management and crop growth.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.154-155
• /
• 2010

최근 Stranski-Krastanov (SK) 성장법을 이용한 자발형성 (Self-assembled) InAs/GaAs 양자점 (Quantum Dot) 연구가 기초 물리학뿐만 아니라 응용에 있어 활발하게 진행되고 있다. 그러나 기존 보고에 따르면 SK 성장법을 통한 InAs/GaAs 양자점은 크기, 균일도, 및 밀도 등의 성장거동 제어에 한계가 있다. 예로, 성장속도 및 증착양이 감소하더라도 상대적으로 크기가 큰 InAs/GaAs 클러스터 (Cluster)를 형성하여 크기분포의 불균일 및 결함을 야기하여 결과적으로 전기/광학적 특성을 저해하는 요인이 된다. 이를 개선하기 위한 방안으로 SK 성장법을 변형한 다양한 수정자발형성법이 제안되어 연구되고 있다. 본 논문에서는 기존 SK 성장법과 Arsenic-interruption Technique(AIT), In Pre-deposition (IPD)법을 각각 접목한 수정자발형성법을 이용하여 상대적으로 크기가 큰 InAs/GaAs 양자점 또는 클러스터 형성을 감소시켜 공간적 크기 균일도 및 밀도를 제어한 결과를 보고한다. 성장된 InAs/GaAs 양자점 시료의 구조 및 광학적 특성을 원자력간현미경 (Artomic Force Microscopy, AFM)과 Photoluminescence (PL) 분광법을 이용하여 분석하였다. 기존 SK 성장법을 이용하여 형성한 기준시료의 AFM 이미지에서 InAs/GaAs 양자점과 클러스터의 공간밀도는 각각 6.4*1010/cm2와 1.4*109/cm2로 관찰되었다. 그러나, AIT를 이용한 양자점 시료의 경우 상대적으로 크기가 큰 InAs/GaAs 클러스터는 관찰되어지지 않았고, 양자점 밀도는 8.4*1010/cm2로 SK 양자점에 비하여 30% 정도 개선되었다. 또한, InAs/GaAs 클러스터를 제외한 공간 균일도는 SK-InAs/GaAs 양자점의 15.6%에 비하여 8%로 크게 개선된 결과를 얻었다. AIT 성장법을 이용한 InAs/GaAs 양자점에서 원자의 이동거리 (Migration Length)의 제어로 양자점의 형성특성이 개선된 것으로 설명할 수 있으며, Arsenic 차단 시간이 임계점 이상으로 길어지면 다시 InAs/GaAs 클러스터들이 형성되는 것을 관찰할 수 있었다. InAs/GaAs 양자점과 클러스터 형성 특성이 초기 표면 조건에 어떻게 영향을 받는지 분석하기 위해, InAs 양자점 성장 이전에 V족 물질 공급 없이 Indium의 공급시간을 1초(IPDT1S 시료), 2초 (IPDT2S 시료), 3초 (IPDT1S 시료)로 변화시키면서 증착하고 기존 SK 성장법으로 양자점을 성장하였다 (IPD성장법). 그 결과 IDP1S 양자점 시료의 공간밀도가 10*1010/cm2로 SK InAs/GaAs 양자점 시료에 비해 약 60% 정도 증가하였고, 클러스터도 관찰 할 수 없었다. 그러나 IPD 시간이 증가할수록 다시 InAs/GaAs 클러스터들이 형성되는 것을 관찰할 수 있었다. 이러한 결과는 InAs/GaAs 양자점 성장초기에 InAs 핵생성 사이트 (Nucleation site)의 크기 및 상태를 제어하는 것이 양자점의 밀도 및 균일도를 제어하는 중요한 요소임을 알 수 있다.

• Polymer(Korea)
• /
• v.38 no.5
• /
• pp.640-644
• /
• 2014

As a process of plat panel display production, slot coating is widely used for the coating of photoresist on a wide glass substrate. A uniform coating thickness is important, and the coating uniformity is divided into nozzle and machine directions. The machine and nozzle directions coating uniformities are influenced by the operation condition of coater and flow uniformity inside the die, respectively. Non-uniform coating during steady coating process occurs according to those factors, however, non-uniform coating along the machine and nozzle directions has been observed at the beginning of coating by unsteady flow. In this study, steady and unsteady state flow simulations have been performed and compared with experiment to examine the causes of non-uniform coating. Computational results exhibited that it took a time to get a uniform pressure distribution at whole inside the die, and during this period of time edge regions showed lower exit velocity compared with center region. Subsequently edge regions had thinner coated layers than center region. However edge regions showed higher exit velocity than center region after steady state, and this made edge regions had thicker coated layer than center region.

• Clean Technology
• /
• v.18 no.1
• /
• pp.76-82
• /
• 2012

The paper includes utlization of zeolite as potential adsorbent to remove a hazardous malachite green from waste water. The adsorption studies were carried out at 298, 308 and 318 K and effects of temperature, contact time, initial concentration on the adsorption were measured. On the basis of adsorption data Langmuir and Freundlich adsorption isotherm model were also confirmed. The equilibrium process was described well by Freundlich isotherm model, showing a selective adsorption by irregular energy of zeolite surface. From determined isotherm constants, zeolite could be employed as effective treatment for removal of malachite green. From kinetic experiments, the adsorption process followed the pseudo second order model, and the adsorption rate constant ($k_2$) decreased with increasing initial concentration of malachite green. Thermodynamic parameters like activation energy, change of free energy, enthalpy, and entropy were also calculated to predict the nature adsorption. The activation energy calculated from Arrhenius equation indicated that the adsorption of malachite green on the zeolite was physical process. The negative free energy change (${\Delta}G^{\circ}$ =-6.47~-9.07 kJ/mol) and the positive enthalpy change (${\Delta}H^{\circ}$ = +32.414 kJ/mol) indicated the spontaneous and endothermic nature of the adsorption in the temperature range 298~318 K.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.10
• /
• pp.270-276
• /
• 2019

According to the International Maritime Organization (IMO) 2020 Regulation, ships operating outside designated emission control areas (ECA) have to use low-sulfur oil with a sulfur content of 0.5% or less by January 2020. To minimize the consumption of high-priced low-sulfur oil, it is urgent to introduce efficient energy-saving devices (ESD), and contra-rotating propeller (CRP) systems are well known to be the most effective one. The shafting system that drives a CRP is composed of an inner shaft and an outer one and has a mutually influential system that is much more complex and heavier than a general shafting system. An initial design was carried out to install a CRP system for the first time in Korea. The purpose of this study is to verify whether the journal bearing meets the classification's design criteria through a bearing reaction force analysis for the classification's approval of the initial design. It is ideal for the thrust of the propeller to act on the center of the shaft, but thrust eccentricity occurs due to the uneven wake caused by the stern shape. Load conditions were applied while considering thrust eccentricity to perform the shaft analysis, and the results were compared with the classification's criteria.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.41 no.3
• /
• pp.295-301
• /
• 1996

This study was carried out to clarify the effect of sprout length, burried depth of seed and CaO$_2$ seed coating on emergence, seedling stand and early growth of rice in puddled-soil drill seeding at Junbuk in 1995. The cultivar tested was Dongjinbyeo(Japonica type). Although the longer sprouted seeds were caused the better seedling stand, 4mm sprout length of seeds appeared to be appropriate for good seedling stand and seeding uniformity, while 6mm sprouted seed resulted in ununiform seedling establishment. Rapid emergence and increased seedling stand were obtained by CaO$_2$ seed coating, which had effect more on soaked seed than on sprouted seed, but the seedling stand of sprouted seeds significantly reduced at deeper than 1cm seeding depth and also emergence rate of sprouted seeds significantly reduced at deeper than 2cm seeding depth.

• Progress in Medical Physics
• /
• v.26 no.3
• /
• pp.119-126
• /
• 2015

The purpose of this study is to analyze motion-induced dose error generated by each tumor motion parameters of irregular tumor motion in helical tomotherapy. To understand the effect of the irregular tumor motion, a simple analytical model was simulated. Moving cases that has tumor motion were divided into a slightly irregular tumor motion case, a large irregular tumor motion case and a patient case. The slightly irregular tumor motion case was simulated with a variability of 10% in the tumor motion parameters of amplitude (amplitude case), period (period case), and baseline (baseline case), while the large irregular tumor motion case was simulated with a variability of 40%. In the phase case, the initial phase of the tumor motion was divided into end inhale, mid exhale, end exhale, and mid inhale; the simulated dose profiles for each case were compared. The patient case was also investigated to verify the motion-induced dose error in 'clinical-like' conditions. According to the simulation process, the dose profile was calculated. The moving case was compared with the static case that has no tumor motion. In the amplitude, period, baseline cases, the results show that the motion-induced dose error in the large irregular tumor motion case was larger than that in the slightly irregular tumor motion case or regular tumor motion case. Because the offset effect was inversely proportion to irregularity of tumor motion, offset effect was smaller in the large irregular tumor motion case than the slightly irregular tumor motion case or regular tumor motion case. In the phase case, the larger dose discrepancy was observed in the irregular tumor motion case than regular tumor motion case. A larger motion-induced dose error was also observed in the patient case than in the regular tumor motion case. This study analyzed motion-induced dose error as a function of each tumor motion parameters of irregular tumor motion during helical tomotherapy. The analysis showed that variability control of irregular tumor motion is important. We believe that the variability of irregular tumor motion can be reduced by using abdominal compression and respiratory training.

• Nuclear Engineering and Technology
• /
• v.16 no.2
• /
• pp.70-79
• /
• 1984

With the help of the nuclear computational system for a large LMFBR (KAERI-26 group cross section library/1DX/2DB), the reactivity coefficients for the diagrid expansion and the pad expansion at the beginning of cycle of the equilibrium core of SUPER-PHENIX I are calculated and reviewed. the core is described using R-Z geometry model, and a two-dimensional multigroup diffusion theory is used. For reference cases, reactivity calculations for radial and axial uniform expansion are performed, and also calculated are reactivity variations due to changes in material density and core volume. The reactivity coefficient for the diagrid expansion is calculated to be -0.553pcm/mil. The temperature coefficient corresponding to the above value is -1.0766pcm/$^{\circ}C$ and is well in accord with the French datum of -1.09pcm/$^{\circ}C$ within 1.2% difference. With the use of 4he calculational method for the diagrid expansion effect, reactivity calculations for the pad expansion bringing about nonuniform expansion are performed, which show that the calculational method is very useful in the analysis of the pad expansion effect. The reactivity coefficients for the pad expansion are calculated to be -0.2743 pcm/mil and -0.2786pcm1mi1 for the averaged expansion model and for the integrated pancake model, respectively. Under the assumption of the free expanding core the temperature reactivity coefficients for each model are obtained to be -0.5766pcm/$^{\circ}C$ and -0.5858pcm/$^{\circ}C$, both of which agree with the French datum of -0.574pcm/$^{\circ}C$ within 2% difference.

• Korean Journal of Environmental Agriculture
• /
• v.27 no.2
• /
• pp.171-177
• /
• 2008

The application in agricultural fields of pig slurry composting biofiltraton amending smell and nutrient unevenness, it is important for the appropriate nitrogen nutrient management to promote the availability of the crops and to minimize the risk of adversely environmental effects. The objective of this study was to determine the application rates of the preplant pig slurry composting biofiltration for red pepper(Capsicum annuum L.) by considering the yield response and the fruit quality such as sugar, capsaicinoid content. Red peppers were grown on plastic film ground under five different pig slurry(PS) application rates and mineral fertilizer(MF 100%) as a control. The effects of a single application of five different doses of PS: PS 0%(no kg N $ha^{-1}$), PS 50%(51.5 kg N $ha^{-1}$), PS 75%(77.3 kg N $ha^{-1}$), PS 100%(103 kg N $ha^{-1}$) and PS 125%(129 kg N $ha^{-1}$) were compared with the recommended mineral treatment(103 kg N $ha^{-1}$) in the pre-planting. The sidedressing N application(87 kg N $ha^{-1}$) was applied to the mineral fertilizer in all treatments. Red peppers were harvested at the mature red stage through five times from 72 days after transplanting(DAT) to 133 DAT. The results indicated that the yield of red pepper was increased with the increase of the N application rates from PS 0% to PS 100%. The highest yield was obtained in PS 100% by 20,843 kg $ha^{-1}$, although there were no significant differences in yield among PS 100, PS 125% and MF 100%. In addition, The contents of soluble sugar and capsaicinoids were not significantly different in all treatments. Accordingly, fertilization recommendations of red pepper to substitute PS for the mineral fertilizer were considered to PS 100%.