• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.8
• /
• pp.110-118
• /
• 2013

This paper describes the development of DSSS wireless communication uplink system for missile remote control. In consideration of low probability of intercept, low probability of exploitation, anti-jam, low latency, and doppler frequency offset, we used DSSS partially DBPSK. Also we used the selective diversity with two receiving antennas to mitigate multipath interference which is the dominant channel impairment and the turbo product code(TPC) for forward error correction(FEC) to improve bit error rate performance.

• Journal of Aerospace System Engineering
• /
• v.7 no.3
• /
• pp.7-14
• /
• 2013

Hypersonic vehicles over Mach 5 need active cooling or thermal management systems to resolve excessive heating problems on their fuselage and engines. Endothermic fuels are widely used these days not only for the energy source but also for a heat sink. Therefore, fuel supply systems of hypersonic vehicles should be mainly composed of adiabatic fuel storage tank, cooling systems for the airframe and engine/nozzle, and fuel supply/injection systems in high pressure, high temperature, and high fuel flow rate conditions. This paper describes a conceptual design process of a hypersonic fuel supply system in order for designing a layout of the system, and identifying components and their specification requirements.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.2
• /
• pp.54-62
• /
• 2010

This paper describes the development of high fidelity air data processing algorithm which can be applied into an air data system for a high speed aerial vehicle. Unlike the previous air data system, current algorithm used several pre-determined pressure data which were obtained with computational fluid dynamic approach without using total pressures having enough sensor redundancy and fault detection ability. The verification of current algorithm was done by commercial software Matlab and Simulink.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.6
• /
• pp.483-488
• /
• 2007

The aerodynamic characteristics of FAST(Future Air Speed Transit) combined the body with tandem wing flying over nonplanar ground surface are investigated by using a boundary element method. To validate the present method, results of the present analysis are compared with the experiment and other numerical results. The arrangement of the tandem wing is determined to secure sufficient aero-levitation force and the stability through the analysis of the aerodynamic characteristics of the FAST. The FAST has the maximum lift characteristics when the tandem wing with lower endplate is located at the front side and the rear side of the body. The stability of the FAST can be secured by using the flaperon of the tandem wing.

• Composites Research
• /
• v.27 no.4
• /
• pp.123-129
• /
• 2014

Ceramic matrix composites (CMCs) consist of such reinforcements as carbides, nitrides, borides and oxides, which have high melting points, low density, high modulus and high strength, for the purpose of increasing toughness. These materials are used for heat shielding systems for aerospace vehicles, high-temperature gas turbine combustion chambers, turbine blades, stator vane parts, etc. Oxide CMCs are used for the components of burner and flame holder and the high-temperature gas duct. CMCs are also applied to brake disks, which are subjected to severe thermal shock, and slide bearing parts under heavy loads. The research and development of the CMC are progressed for the strategic purpose in defense and energy industry; for instance, for aerospace applications in the U.S., and for hyper-speed aircraft, gas turbines, and atomic fissions in U.S., Japan, and Europe.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.1
• /
• pp.58-65
• /
• 2018

To improve the performance of high-speed vehicles, various studies have been carried out on the head of vehicles. In this study, tests are conducted on flow characteristics and drag reduction using counterflow air jets in supersonic flow. The flow is visualized by the Schlieren method using a high-speed camera, and the drag is measured using a torque sensor according to the injection pressure conditions. The results of the measurements indicate that the flow changes from unsteady state to steady state for injection pressure ratios between 1.58 and 1.70, and drag reduction is observed as the pressure of the counterflow air jets increases.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.3 s.106
• /
• pp.295-306
• /
• 2006

In this paper, we proposed and implemented a novel antenna cover mounted over a microstrip path antenna for ultrafast aircraft. A protective antenna cover prevents alteration in the electrical characteristics of the antenna due to environmental conditions. The permittivity of the cover materials should be practically invariable at all operating frequencies. We evaluated the characteristics of the antenna with both simulation and experiment. The experimental results show that the proposed antenna cover can be useful for ultrafast aircraft.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.6
• /
• pp.57-63
• /
• 2017

In this study, the fundamental test for drag reduction is carried out by using a plasma generator. Fundamental test setup is constructed of visualization and drag measurement system. The schlieren technique is used to visualize the plasma counterflow in supersonic flow. The penetration of the plasma jet and the change of the flow structure are observed through visualization results. Load cell is used to confirm possibility of drag reduction. Results show that drag was reduced by 6.2% using plasma jet in supersonic flow.

• Journal of Institute of Control, Robotics and Systems
• /
• v.11 no.3
• /
• pp.246-253
• /
• 2005

An experimenal study on flight control of high-speed AEV(Aero-levitation Electric Vehicle) scale model in wind-tunnel is conducted. The AEV is to fly at very low altitude in predesigned track so that it is always under the wing-in-ground effect. The experiment is intended to fly the scale model to follow the predesigned altitude schedule while holding its attitude (pitch, roll, and yaw). Especially, the altitude changes for climb, cruise, and descent with constant pitch angle are most important maneuvers. The experiment shows that the required mission flights can be performed with appropriate sensors, processors, and actuators.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.2
• /
• pp.99-107
• /
• 2016

Test research on Infra-Red Thermography(IRT) technique in a supersonic wind tunnel has been conducted. Inadvertent technical difficulties and their solutions associated with the technique in running of the facility were examined. Two flow conditions at Mach number of 3 and 4 were considered. A double compression ramp model, that replicates realistic high-speed vehicle configuration, was used as test model. The present IR data were compared with shadowgraph visualization images and laminar computational fluid dynamics(CFD) results. It has been shown that the IRT technique can be used in quantifying various fluid dynamic features such as flow transition, separation and three-dimensional phenomena around the double compression ramp model.