• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.1
• /
• pp.89-94
• /
• 2014

The high Young's modulus and tensile strength of carbon nanotubes has attracted great attention from the research community given the potential for developing super-strong, super-stiff composites with carbon nanotube reinforcements. Over the decades, the strength and stiffness of carbon nanotube-reinforced polymer nanocomposites have been researched extensively. However, unfortunately, such strong composite materials have not been developed yet. It has been reported that the efficiency of load transfer in such systems is critically dependent on the quality of adhesion between the nanotubes and the polymer chains. In addition, the waviness and orientation of the nanotubes embedded in a matrix reduce the reinforcement effectiveness. In this study, we carried out performed micromechanics-based numerical modeling and analysis by varying the geometry of carbon nanotubes including their aspect ratio, orientation, and waviness. The results of this analysis allow for a better understanding of the load transfer capabilities of carbon nanotube-reinforced polymer composites.

• Aerospace Engineering and Technology
• /
• v.12 no.2
• /
• pp.48-56
• /
• 2013

In this paper, the equivalent elastic properties of fiber reinforced plastic laminar are investigated using various homogenization schemes. Although there are several methods for predicting the equivalent elastic properties such as analytical formula or semi-empirical formula, most of them have some limitations or are not much accurate when handling new composite material consisting of various fiber, matrix and fiber-volume fraction ratio. To resolve the issues, computational homogenization scheme is adopted with a representative volume element (RVE) comprised of a set of finite elements. Finally, the equivalent elastic properties are obtained by applying periodic boundary conditions. The obtained results are compared with those by the existing methods and test results. Also its effect on structural analysis results of the composite satellite panel is investigated.

• Journal of the Mineralogical Society of Korea
• /
• v.18 no.4 s.46
• /
• pp.249-257
• /
• 2005

Garnet is one of the major minerals down to the top of lower mantle approximately 660 km with spinel and pyroxenes. Garnet transforms into perovskite and corundum in the lower mantle, however its sequence is still in controversy. We measured the compressibility of a natural almandine at high-pressure up to 62 CPa using Mao-Bell type diamond anvil cell (DAC) at room temperature. Chemical formula of the specimen is ($Fe_{2.52}Ca_{0.21}Mg_{0.18}Mn_{0.12})Al_{2.23}Si_{2.97}O_{12}$. Results of this compression study are as follows: a : $10.175\;{\AA}$, V : $1251.16\;{\AA}^{3}$, $D_{x}$ : $5.265\;g/cm^{3}$ at 62 GPa; bulk modulus is 156 GPa using Birch-Murnaghan equation of state (EoS) with a fixed $K_{0}\;'$ of 4. This study would be the first time attempt accomplished with the high pressure DAC using synchrotron radiation at the Pohang Light Source (PLS) in Korea.

• Magazine of the Korea Concrete Institute
• /
• v.9 no.4
• /
• pp.125-135
• /
• 1997

경량기포콘크리트란 시멘트슬러리 속에 미리 생성된 기포를 혼합시켜 양생시킴으써 동일한 체적의 보통콘크리트보다 가볍게 만든 콘크리트를 의미한다. 따라서 경량기포콘크리트는시멘트풀 결합재내에 기포가 무작위로 분포된 복합재료이다. 본 연구의 목적은 이러한경량기포콘크리트의 탄성계수 추정식을 미시역학적 이론을 바탕으로 추정하는데 있다. 이르 위해 본 논문에서는 미시역학적인 미분법에 Hansen의 수정기법을 적용한 수정미분법을 사용하여 경량기포콘크리트의 탄성계수 추정식을 제안하였다. 제안된 추정식을 사용하여 얻어진 결과는 실험결과와 잘 일치하였고 기존의 어떤 추정식보다도 우수한 결과를 보였다.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1992.11a
• /
• pp.69-76
• /
• 1992

섬유강화 복합재료의 동탄성계수와 감쇠특성을 규명하기 위하여 랜덤하게 분포된 무한 실린더 형상의 산란체를 가진 점탄성 매질내에서 , 축방향으로 분극되어 조화 운동을 하는 탄성파의 전파에 관하여 연구하였다. 다중 산란에 관한 이론으 이용하여 매질내에서의 파동전파 특성을 내포하는 분산관계식을 얻었다. 다중산란에 의한 실린더간의 상호작용을 수식화하기위하여 필요한 실린더의 쌍분포함수는 몬테카를로 모의 실험을 이용하여 구하였다. 수치적으로 구한 감쇠계수 및 유효전단강성을 주파수와 체적율의 함수로 제시하였다. 또한 감쇠계수의 주파수에 따른 변화에 있어서, 저주파에서는 매질의 점탄성 손실이 지배적이며, 고주파수로 갈수록 다중산란에 의한 손실이 지배적인 것으로 나타났다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.8 no.2
• /
• pp.33-40
• /
• 1988

In this study, effects of the density of soil and the confining pressure applied to the soil sample on the elastic moduli of subgrade soils are experimentally analyzed. Through investigation of subgrade materials of domestic expressways, five typical types of subgrade soils are selected for the experiments. A series of unconsolidated undrained triaxial tests is performed on samples prepared with various water contents and densities at the confining pressures of 1.02, 2.04, and $3.06kg/cm^2$. Initial tangent modulus is inferred from the unloading-reloading portion of the stress strain curve obtained during an individual loading-unloading-reloading test. As a result of the analysis, it is found that the effect of the confining pressure on the elastic modulus of subgrade material is well consistent with the equation proposed by Janbu, and that the elastic modulus can be related to the dry unit weight expressing the Janbu constants as exponentiial functions of it. It is also found that the water content has little effect on the elastic modulus for the samples with the degree of saturation less than 70%.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.3C
• /
• pp.159-166
• /
• 2008

The stress-strain behavior of soils can usually be regarded as non-linear, while it is also known that the soil exhibits the linear-elastic behavior at pre-failure state (very small strain range, $<10^{-3}%$). This study aims to analyze the variation of anisotropic elastic shear moduli of granular soils in various stress conditions. The stress probe experiments with the triaxial testing device equipped with local strain gages and multi-directional bender elements were conducted. When the stress ratio exceeds the range between -0.5 and 1.5, the elastic shear stiffness in the axial direction deviates from the empirical correlation with current stresses, which indicates that the yielding of soils alters the internal pathway through which the elastic shear wave propagates. The experimental results show that the variation of elastic shear moduli in the horizontal direction closely relates to the volume change of soils.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.119-122
• /
• 2011

분자동역학 전산모사를 통하여 에폭시에 다양한 반경의 구형 실리콘 카바이드를 삽입한 나노복합재를 모델링하고, 이들의 기계적 물성과 열적 물성 해석을 다양한 온도조건 하에서 수행하였다. 전산모사 결과 동일한 체적분율 하에서 나노복합재는 입자의 크기가 작아질수록 탄성계수와 전단계수가 상승하는 동시에 선팽창계수는 감소하는 입자의 크기효과를 보였다. 또한 온도 상승에 따른 기계적 물성의 하락이 잘 관찰되었다. 본 연구에서는 이러한 분자동역학 해석 결과를 바탕으로 다양한 온도조건 하에서의 입자의 크기효과를 고려한 멀티스케일 3상 모델을 제시하였다. 유리상 조건 범위에서 온도 변화에 따른 나노복합재 계면의 열응력텐서와 열변형률텐서의 정보를 통해 복합재 내에서 계면이 차지하는 부피비를 온도에 대한 함수로 고려하고, 이를 멀티스케일 모델에 반영함으로써 다양한 온도조건에 대한 나노복합재 열탄성 물성의 예측해를 제시하였다. 본 연구에서 제시한 모델에서 계산된 3상 복합재의 물성은 분자동역학 전산모사의 결과에서 나타나는 나노입자의 크기효과를 잘 반영하였다.

• Composites Research
• /
• v.25 no.2
• /
• pp.34-39
• /
• 2012

A thermo-poro-elastic constitutive model of unidirectionally fiber-reinforced composite materials is suggested by extending the unmixing-mixing scheme which is based upon composite micromechanics. The strain components of thermal expansion due to a temperature change, gas pressure in pores, and chemical shrinkage are included in the constitutive model. On purpose to verify the derived constitutive relations, the representative volume element of two-dimensional lamina subject to various loading conditions is analyzed by the finite element method. The overall stress and strain responses are obtained, and compared with the predicted values by the unmixing-mixing scheme. The numerical results show the usefulness of the proposed model to predict the thermoelastic behavior of porous composites.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.4
• /
• pp.73-78
• /
• 2004

The conventional SLT(Shear Lag Theory) which has been proven that it can not provide sufficiently accurate strengthening predictions in elastic regime when the fiber aspect ratio is small. This paper is an extented work to improve it by modifying the load transfer mechanism called NSLT(New Shear Lag Theory), which takes into account the stress transfer across the fiber ends and the SCF(Stress Concentration Factor) that exists in the matrix regions near the fiber ends. The key point of the model development is to determine the major controlling factor among the material and geometrical coefficients. It is found that the most affecting factor is the fiber/matrix elastic modulus ratio. It is also found that the proposed model gives a good result that has the capability to correctly predict the elastic properties such as interfacial shear stresses and local stress variations in the small fiber aspect ratio regime.