• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.3
• /
• pp.171-178
• /
• 2013

In this study, the sludge that occurs in the initial operation of coagulation system developed for the treatment of CSOs were returned to the flocculation reactor. The purposes of this study were to analyze the Characteristics of flocs that are generated through the recycling sludge and settling characteristics of sludge, and to evaluate the possibility that high concentrations of particulate matter in the initial inflow of CSOs could be used as an weighted coagulant additive. As a result, the concentration of treated CSOs pollutants at the beginning of the CSOs influent with a large amount of particulate matter over 20 ${\mu}m$ was low, after gradually increasing the concentrations of them. The flocs generated from the sludge return were similar in size compared to flocs generated through injection of micro sands, and settling velocity in case of return sludge injection was decreased from 55.1 cm/min to 21.5 cm/min. SVI value of the sludge accumulated at the bottom of the sedimentation tank was 72, and settled sludge volume decreased rapidly due to the consolidation of sludge to the time it takes to 10 minutes. these mean that sludge used for recycling has good settling characteristic. A condition of returned sludge which is 0.1% return of 0.3% extraction was formed in the balance of settlement and extraction. In this case, This condition was to be adequate to maintain the proper concentration such as 100~200 mg/L of TS and 50~100 mg/L of VS in the flocculation reactor. The usage of the return sludge containing particulate matters of CSOs as an weighted coagulant additive was able to secure a stable treated water quality despite the change of influent water quality dynamically. Furthermore, it can be expected to reduce the alum dosage along with the sludge production.

• Journal of Animal Environmental Science
• /
• v.11 no.3
• /
• pp.197-206
• /
• 2005

This study was carried out to investigate the concentration and characteristics of dust originating from windowless broiler building in each season. 12.0m width and 46m tenth with side wall height of 3.0m was investigated and capacity was 12,800 birds at a stock density of 23.2 birds per square meter. Dust concentrations in terms of total suspended particles (TSP), and particulate matter of sizes $10{\mu}m(PM10),\;2.5{\mu}m (PM2.5),\;and\;1{\mu}m(PM1)$ were measured at 30-minute intervals. On the basis of broiler age, the average dust concentration in summer in TSP as follows: 1,229 904.5 558.8 and $1,053{\mu}g/m^3$ on the broilers' first to fourth week of age, respectively. But during winter, the average dust concentration showed an increasing pattern, as follows: 465.4, 1,401, 4,497, 5,097 and $6,873{\mu}g/m^3$ on the broilers' first to fifth week of age, respectively. The maximum dust concentration of $11,132{\mu}g/m^3$ was observed on the fifth week. On a daily basis, the maximum dust concentration during summer was detected in early morning, and the minimum in the afternoon. The aerial dust particle size of $0.05\~0.35{\mu}m$ was the highest in number. But on volume basis, particle size of 16~99 un had the largest percentage in the broiler house. Crude protein of the dust $(42.8\~65.2\%)$, on dry matter basis, was higher than that $(20.5\~24.5\%)$ fed to the broilers. Heavy metal concentration of the dust also had high levels compared with that of the feed.

• Journal of the Korean earth science society
• /
• v.37 no.4
• /
• pp.218-229
• /
• 2016

The bedform stability diagram indicates the shape and size of bedforms that will occur to a given grain size and flow velocity. The diagram has been constructed from experimental data which have been mostly acquired by flume experiments. Generally, the flume experiments have been performed on well sorted sediments with unimodal grain size distribution, in order to understand relationship between grain size and flow velocity. According to the diagram, a ripple structure initiates to be formed from lower flow regime flat bed, as the flow velocity increases on the surface of fine-sand or medium-sand sediments. This study aims to verify that the experimental result of bedform stability diagram will be reproduced in our flume experimental systems, and also to confirm that the result is consistent not only on well-sorted sand sediments but also on poorly-sorted sand sediments with bimodal grain size distribution. The experimental results in this study show that initiation of 2D or 3D ripple structure on poorly-sorted sand sediments requires higher flow velocity and shear stress than those for initiation of the structure on well-sorted sand sediments. In general, carbonate sediments are characterized by poor sorting due to inactive hydraulic sorting and bimodal grain size distribution with allochems and matrices. The results suggest that the carbonate depositional system possibly need a higher flow velocity for initial formation of 2D or 3D bedform structures. The reason might be the fact that pulling off and lifting of a grain in poorly sorted sediments require more energy due to sorting, friction, stabilization, armour effects, and their complex interaction. This preliminary study warrants additional experiments under various conditions and more accurate analysis on the relationship between formation of bedforms and grain size distribution.

• Korean Journal of Environmental Biology
• /
• v.23 no.2 s.58
• /
• pp.191-199
• /
• 2005

The community structure, vertical distribution and harpacticoids composition of the meiofauna community were observed from five stations in Marian Cove, King George Island and one station on the northeastern side of Nelson Island. Sample was taken by a free-fall corer in December 2002. Generally, 11 taxa of meiofauna were found, and meiofauna abundance ranged from 322 to 1575 indiv. $10cm^{-2}$ (mean 781 indiv. $10cm^{-2}$). Nematodes were the most dominant group, making up $89\%$ of total meiofauna, followed by harpacticoids $(6.8\%)$. Benthic harpacticoids appeared 19 species of nine families at all the stations, and most various taxa appeared at station B (13 species of seven families). For vertical distribution, more than $70\%$ of meiofauna was concentrated in the upper $0\~2cm$ sediment layers, and the density abruptly decreased with depth in all the stations. Total biomass of meiofauna varied between 41 and $360{\mu}gC\;10cm^{-2}$, and overall mean biomass was $205{\mu}gC\;10cm^{-2}$. Also nematodes had the highest percentage of total maiofauna biomass $(62.4\%)$. The analysis results of Canonical Correspondence Analysis between meiofauna community and sediment grain size showed that polychaets, oligochaets and cumaceans were influenced by silt&cray, and sand, granule and pebble had a influence on harpacticoids, kinorhynchs and ostracods respectively. But nematodes were not affected by sediment grain size.

• Economic and Environmental Geology
• /
• v.40 no.3 s.184
• /
• pp.263-275
• /
• 2007

The purpose of this study was to show the pollution characteristics of hazardous elements from roadside dust in the Gwangju city. We collected 47 samples from November to December in 2004 and separated four groups such as residential area, industrialized area, downtown area and heavy traffic area fer characteristics comparison on hazardous elements. Roadside dust mostly consisted of quartz, albite, microcline, muscovite in XRD analysis. Content of hazardous elements varied: As $3.4{\sim}11.9 ppm$, Cd $0.2{\sim}28.2 ppm$, Co $32{\sim}526 ppm$, Cr $25{\sim}526 ppm$, Cu $11{\sim}375 ppm$, Ni $14{\sim}247 ppm$, Pb $13{\sim}413 ppm$ and Zn $101{\sim}972 ppm$. Average contents of hazardous elements of Zn>Cu>Pb>Cr>Co>Ni>Cd. Content of hazardous elements was low in residential area, whereas that of heavy metal was much the same in both in heavy traffic area. Content of hazardous elements such as Cd, Co, Cr, Cu, Ni, Pb, Zn was found to be particularly high in industrialized area. According to these results it was possible to presume that industrialized area was affected by industry activity such as machinery, petrochemical, automobile and electronics industry. The SEM analysis, detected Pb, Cr, Ni, and Fe particles in samples of industrialized area contaminated by industry activity. The correlation coefficient table resulted from the samples of roadside dust showed that there was same direction increase of content between elements. In other words, when the content of Cd increase, Cr and Ni increase, as Cr increase, Cu and Ni increase, as Cu increase Ni increase and Pb increase Zn increase. Based on these results it was possible to predict and interpret similar contamination patterns in this study.

• Journal of the Mineralogical Society of Korea
• /
• v.25 no.4
• /
• pp.185-195
• /
• 2012

Due to the high reduction and sorption capacity as well as the large specific surface area, nanosized mackinawite (FeS) is useful in reductively transforming chlorinated organic pollutants and sequestering toxic metals and metalloids. Due to the dynamic nature in its colloid stability, however, nanosized FeS may be washed out with the groundwater flow or result in aquifer clogging via particle aggregation. Thus, these nanoparticles should be modified such as to be built into permeable reactive barriers. This study employed coating methods in efforts to facilitate the installation of permeable reactive barriers of nanosized mackinawite. In applying the methods, nanosized mackinawite was coated on non-treated silica sand (NTS) and chemically treated silica sand (CTS). For both silica sands, the maximum coating of mackinawite occurred around pH 5.4, the condition of which was governed by (1) the solubility of mackinawite and (2) the surface charge of both silica and mackinawite. Under this pH condition, the maximum coating by NTS and CTS were found to be 0.101 mmol FeS/g and 0.043 mmol FeS/g respectively, with such elevated coatings by NTS likely linked with impurities (e.g., iron oxides) on its surface. Arsenite sorption experiments were performed under anoxic conditions using uncoated silica sands and those coated with mackinawite at the optimal pH to compare their reactivity. At pH 7, the relative sorption efficiency between uncoated NTS and coated NTS changed with the initial concentration of arsenite. At the lower initial concentration, uncoated NTS showed the higher sorption efficiency, whereas at the higher concentration, coated NTS exhibited the higher sorption efficiency. This could be attributed to different sorption mechanisms as a function of arsenite concentration: the surface complexation of arsenite with the iron oxide impurity on silica sand at the low concentration and the precipitation as arsenic sulfides by reaction with mackinawite coating at the high concentration. Compared to coated NTS, coated CTS showed the lower arsenite removal at pH 7 due to its relatively lower mackinawite coating. Taken together, our results indicate that NTS is a more effective material than CTS for the coating of nanosized mackinawite.

• The Korean Journal of Nuclear Medicine
• /
• v.32 no.3
• /
• pp.298-304
• /
• 1998

Purpose: We evaluated the usefulness of Re-188 sulfur colloid for radiation synovectomy and therapy of intraperitoneal metastasis. Materials and Methods: We investigated the labeling efficiency of Re-188 sulfur colloid on various conditions. The stability of Re-188 sulfur colloid was observed at room temperature for 24 h and in human serum and synovial fluid for 72 h. The particle size distribution of Re-188 sulfur colloid was measured by filtering with various pore size filters. Animal experiment was performed in mice and rabbits. Results: The labeling efficiency of Re-188 sulfur colloid was $64.5{\pm}5.8%$ (n=5) at the conditions of sodium thiosulfate 40 mg, EDTA $Na_2.2H_2O$ 0.8 mg, $KReO_4$ 0.8 mg at pH 1. After purification, the radiochemical purity was higher than 99%. The stability of Re-188 sulfur colloid was high (>99%) at room temperature for 24 h and in human serum and synovial fluid for 72 h. The particle size distribution of Re-188 sulfur colloid was 0.3% ($<1{\mu}m$), 11.2% ($1{\sim}5{\mu}m$), 25.8% ($5{\sim}10{\mu}m$) and 52.8% ($>10{\mu}m$). In mice, 1 h postinjection of Re-188 sulfur colloid into tail vein, uptakes in lung, liver and muscle were $37.30{\pm}5.36$, $32.33{\pm}1.79$, $6.60{\pm}0.02%$ ID/organ respectively. After i.p. injection in mice, the uptakes of extraperitonial organs of Re-188 sulfur colloid at 1 and 24 h were $0.1{\pm}0.1$, $0.4{\pm}0.1%$ ID/organ, and the excretions through urine and feces (${\sim}70 h$) were low ($2.68{\pm}0.80$, $0.95{\pm}0.17%$). When Re-188 sulfur colloid was injected to synovial space of rabbit, the uptake in other organs except knee was very low. Conclusion: Re-188 sulfur colloid showed high labeling efficiency, stability and potency for clinical use.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.5
• /
• pp.47-56
• /
• 2014

In winter season, the pore water inside the ground freezes and thaws repetitively due to the cold air temperature. When the freezing-thawing processes are repeated on the ground, the change in soil particle structure occurs and thus the damage of the infrastructure may be following. This study was performed in order to investigate the stiffness change of soils due to the freeze-thaw by using elastic waves. Sand-silt mixtures are prepared with in the silt fraction of 40 %, 60 % and 80 % in weight and in the degree of saturation of 40 %. The specimens are placed into the square freezing-thawing cell by the temping method. For the measurement of the elastic waves, a pair of the bender elements and a pair of piezo disk elements are installed on the cell, and a thermocouple is inserted into soils for the measurement of the temperature. The temperature of the mixtures is decreased from $20^{\circ}C$ to $-10^{\circ}C$ during freezing, is maintained at $-20^{\circ}C$ for 18 hours, is gradually increased up to the room temperature of $20^{\circ}C$ to thaw the specimens. The shear waves, the compressional waves and the temperature are measured during the freeze-thaw process. The experimental result indicates that the shear and the compressional wave velocities after thawing are smaller than those of before freezing. The velocity ratio of after thawing to before freezing of shear wave is smaller than that of the compressional wave. As silt fraction increases from 40 % to 80 %, the shear and compressional wave velocities are gradually increased. This study suggests that the freezing-thawing process in unsaturated soil loosens the soil particle structure, and the shear wave velocity reflects the effect of freezing-thawing more sensitively than the compressional wave velocity.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.40 no.8
• /
• pp.1121-1127
• /
• 2011

We evaluated the quality characteristics of adzuki bean sediment according to variety. The moisture, crude protein, and crude ash contents of the various adzuki bean varieties were 8.2~11.1, 15.4~20.6 and 3.3~3.6 g/100 g, respectively. The potassium contents of Chilbo-pat (CB) and Hongeon-pat (HE) were 875.1 and 873.1 mg/100 g, respectively. The calcium contents of Jungbu-pat (JB) and Kumsil-pat (KS)were 73.6 and 73.2 mg/100 g, respectively. A high level of magnesium (131.4 mg/100 g) was found in Yeonkeum-pat (YK). The yields of adzuki bean sediment according to variety were no different either wet (188.3~204.7%) or dry (62.1~66.0%). The L-values on sediment of YK and KS were 67.0 and 68.0, respectively; however, the CB L-value was low at 54.0. A high level of a- (6.6) and b-value (12.8) was found in YK; however, the values for CB were much lower at 3.8 and 5.9, respectively. There was no difference in particle-size distribution, water binding capacity, and solubility of adzuki bean sediment according to variety. High levels of peak (3.79 RVU), trough (3.75 RVU), final (7.33 RVU), and setback viscosity (3.54 RVU) were found in JB. The sensory properties of products in food processing are important, and the variety of adzuki bean sediment should be chosen depending on desired product characteristics.

• Korean Journal of Optics and Photonics
• /
• v.21 no.2
• /
• pp.82-88
• /
• 2010

Photopolymer is a material for recording three dimensional holograms containing photo information. Photopolymer has been found to be a proper material due to many advantages such as high DE value, easy processing, and low price. Compositions of PVA, monomer, initiater and photosensitizer were determined by previous experiments and the compositions of $SeO_2$ and $TiO_2$ were considered as variable to find out the effects of $TiO_2$ on DE. The DE values were constant for the varying compositions of $TiO_2$ (0.1 mg~1.0 mg). In other words, $TiO_2$ is not directly effective on the DE values. Composition change experiments from $SeO_2$ 0.1 mg, $TiO_2$ 0.9 mg to $SeO_2$ 0.9 mg, $TiO_2$ 0.1 showed a maximum DE value of 73.75% at a component of $SeO_2$ 0.8 mg, $TiO_2$ 0.2 mg. It seemed that regardless of the amount of $TiO_2$, increasing the amount of $SeO_2$ gently increases DE`s. If nano particles are heavily added, transparent films could not be made due to the separation of particles by the solubility decrease. Photopolymer films could be made with high DE values for an extensive angle range if $TiO_2$ additions were kept minimum and $SeO_2$ additions were kept maximum.