• Korean Journal of Plant Resources
• /
• v.12 no.3
• /
• pp.215-220
• /
• 1999

To find out the temporal and spatial variations in contents of sugar, phenolic compounds and mineral, the sap of Acer mono MAX. were harvested from several regions and periods, and those contents were determined by solvent fractionation, TLC, HPLC and atomic absorption spectrophotometer. Most of all the free sugar contained in the sap of Acer mono MAX. was sucrose, with range of 1.35 to 3.41%. The content of total phenolic compound in the sap of Acer mono MAX. was distributed from 0.034 to 0.151 mg/100m1, and most of phenolic acid was phloroglucinol. The contents of Na, K, Ca and Mg were ranged from 24.11 to 33.15, from 13.75 to 22.10, from 47.19 to 88.00 and from 2.48 to 6.31 ppm, respectively. Contents of sugar, phenolic compounds and mineral decreased sharply at the later harvest. Comparing two different methods of the sap harvest, bore method and groove method, the contents of compounds in the study were determined higher with groove method.

• Explosives and Blasting
• /
• v.31 no.2
• /
• pp.1-5
• /
• 2013

Parameters of Swedish bench blast design was analyzed by robust design method. Orthogonal array which is adopted in this study was $L_9(3^4)$ and the parameters were hole diameter, explosive type, hole inclination and rock factor of 3 levels. Result of analysis showed that maximum and minimum burden are most affected by hole diameter, followed by explosive type, rock type and inclination of hole. Parameters affecting specific charge are in the order of rock type, explosive type and to specific drilling are hole diameter and explosive type. Cost analysis showed that robust design is capable of parameter optimization.

• Journal of the korean veterinary medical association
• /
• v.38 no.6
• /
• pp.549-558
• /
• 2002

3.5살짜리 래브라도 리트리버(Labrador Retriever)는 매일 처방되는 피질스테로이드제에 무반응으로 비계절적, 심한 소양증을 2년간 앓고 있는 병력을 갖고 있었다. 공기유래 알레르겐(알러젠; Allergens)들에 대한 시험관내 RAST1(Radioallergosorbent testing; 방사선 알레르기 흡착 시험법)에 양성으로 나타난 것을 기초로 한 면역요법(Immunotherapy)을 18개월 동안 시행했으나 성공적이지 않았다. 부신피질호르몬(Adrenocorticotropic Hormone, ACTH)자극 시험법은 이것이 본래 임상수의사에 의해 발생(Iatrogenic)된 것임을 예시하여준다. 피부 찰과물(Skin scrapings)을 검사한 결과 개 천공개선충(Sarcoptic mange)이라는 진단이 내려졌다. 이버맥틴(Ivermectin)치료효과와 피질스테로이드(Corticosteroid)의 투약중지에 대한 반응이 극적으로 나타났다. 10개월 추적기간(10-month follow-up period)동안에 이 질병은 재발되지 않았다. 이것은 비록 계절적인 알레르겐을 배제하기 위해 긴 기간동안 추적이 필요하였으나 개 천공개선충이 오히려 피질스테로이드요법에 대한 2차적인 것보다는 1차적인 질병이라는 것을 말해준다. 아토피의 진단을 위해 혈청학적 시험법의 이용이 논의되었다.

• Explosives and Blasting
• /
• v.19 no.1
• /
• pp.31-40
• /
• 2001

일반적으로 장공발파(長孔發破) 방법(Long hole blasting method)은 그동안 주로 대규모 채탄막장이나 댐 기초굴착, 광산 등에서 행하여져 왔으나 최근 토목터널에서 시공 효율성 및 경제성을 목적으로 관심이 높아지고 있다. 기존의 터널설계 패턴은 I -Type을 기준으로 3.5~3.8m 천공이며 신공법 적용시 최대 4.Om까지 설계되는 것이 보통이었다. 과거 착암장비는 천공장이 늘어남으로서 슬러지에 의한 천공속도가 저하되어 천공비가 증가하기 때문에 빠른 슬러지 배제가 필요하고 Rod의 휨 현상에 의한 천공오차의 증대를 초래할 수 있는 단점이 있었다. 그러나 최근 장비의 발달로 인하여 천공각도 및 천공장 등을 Computer로 모니터링하여 제어할 수 있어 정밀한 천공이 가능하여 졌고 또한, 고성능 에멀젼계 폭약(Super Emulsion)의 개발로 그동안 극 경암터널에서 에멀젼계 폭약의 단점으로 여겨졌던 비 장약량의 증대와 사압현상의 발생, 굴진효율 저하문제론 극복할 수 있었다. 따라서 본 연구는 현재 건설중인 대상현장을 중심으로 장공 터널발파의 효율성과 경제성을 분석하고 나아가 암질에 따른 새로운 Type별 설계기준을 마련하는 기초자료로서 활용하고자 하였다. 된 연구의 대상현장은 충북 괴산군 영풍면 소재 중부내륙(여주-구미간) 고속도로 제 9공구 이화터널 건설공사현장으로 $\varphi{102mm}$ 무 장약공 Cylinder 4공을 이용한 심발법을 사용하였으며 천공장은 최대 5.0m로 2000년 11일 15일에서 동년 12월 15일까지 31일간 총 112회의 시험발파를 실시하여 평균 92%의 높은 굴진 효율을 기록하였다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.920-923
• /
• 2004

천공 요소는 자동차나 공조기 등의 유체기계의 흡/배기계에 널리 사용된다. 천공요소는 일반적으로 유동과 소음원이 동시에 존재하는 환경에서 사용되며, 유동 및 음압 레벨의 변화에 의해서 큰 영향을 받게 된다. 천공요소의 임피던스의 변화는 소음기의 음향학적 특성에 영향을 미치게 되므로, 유동이나 음압 조건이 임피던스에 미치는 영향에 대한 연구가 중요하다. 본 연구에서는 통과하는 유동이 존재하는 천공요소의 임피던스를 실험을 통하여 측정하고 경계요소법을 사용하여 예측하였다. 측정 및 예측된 임피던스를 무차원화 해석을 수행하여 영향을 미치는 인자들을 분석하였다.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.3
• /
• pp.115-121
• /
• 2008

A knowloedge of the residual stress distribution at circumferential welds can increase the prediction accuracy of a fracture assessment in pipe lines. In this study, in order to predict the residual stress distribution in the circumferential butt-welded pipes were measured, using the hole-drilling strain gauge method. Their practical applications were performed in to two kinds of pipes. As the results, the following characteristics were found. On the inner surface of pipes, the circumferential and axial residual stresses were both tensile near the center line of welding and both of them changed from tensile to compressive as the distance from the center line increased. On the outer surface, however, the circumferential residual stress was shown to be tensile wile the axial residual stress was compressive near the center line of welding, and later they were revered at the region far away from the centerline.

• Cement Symposium
• /
• no.3
• /
• pp.73-82
• /
• 1976

• The Journal of the Acoustical Society of Korea
• /
• v.39 no.4
• /
• pp.270-278
• /
• 2020

In this paper, sound transmission of Micro-Perforated Plates (MPPs) installed in an impedance tube with a circular cross-section is described using an analytic method. Vibration of the plates is expressed in terms of an infinite series of modal functions, where modal function in the radial direction is given by the Bessel function. Under the plane wave assumption, a low frequency approximation is derived, and a formula for the sound transmission coefficient of multi-layered MPPs is presented using the transfer matrix method. The Sound Transmission Losses (STLs) of single and double MPPs are computed using the proposed method and compared with those done by the Finite Element Method (FEM), which shows an excellent agreement. As the perforation increases, the STL is degraded, since the STL becomes dominated by the perforation ratio rather than by vibration of the plate. The STL shows dips at natural frequencies as well as at the mass-spring-mass resonance frequency. The proposed model for the STL prediction in this study can be applied to an arbitrary number of MPPs, where each MPP may or may not have a perforation.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.11
• /
• pp.87-98
• /
• 2007

For the quick rehabilitation of a fire-damaged tunnel structure, it is the most important procedure to investigate the fire-induced damaged zone rapidly. This study aims to propose a new drilling resistance testing method by which mechanical properties of tunnel concrete lining altered by high temperature can be estimated easily and continuously. Especially, it alms to derive the relationships to estimate mechanical properties of mortar and concrete materials from drilling parameters. To obtain the optimum testing condition, a series of drilling resistance tests were carried out for mortar specimens. When the rotation per minute of drill bit, tile penetration rate and the bit diameter were 1,300 rpm, 1.40 mm/sec, and 10 mm respectively, the deviation of measured drilling resistance forces was minimal. Under the optimum testing condition, the relationships between drilling resistance and mechanical properties of mortar specimens were shown to be very favorable. The concept of replacing a mean value of resistance farces measured during drilling with the resistance energy was proposed to consider the effects of randomly distributed aggregates inside a concrete material on drilling resistance. When the concept was applied to concrete materials, a favorable relationship between actual compressive strength and drilling resistance energy was also successfully derived.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.1
• /
• pp.16-21
• /
• 2001

Improvement of sound absorption capability of wood and wood-based board by resonant absorption was attempted. Sound absorption coefficients of wood and wood-based board which contain normal, simple perforation and stair type perforation had been estimated by the tube method using standing wave ratio. Sound absorption coefficients of wood specimens of simply perforated and perforated with stair were higher than that of normal specimens. Especially, in case of stair type perforation, it was about 50 to 60% higher than that of normal specimen in the frequency of 3 to 4KHz. It was considered that the cavity which had been formed by perforation with stair type behaved as a single resonator. Wood-based board showed good sound absorption coefficients in the frequency from 125Hz to 2KHz and that of perforated board showed a little higher in the frequency from 300Hz to 500Hz than that of normal board. The computed data of resonant frequencies at several sizes of cavity showed good accordance with the estimated data of those.