• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.1A
• /
• pp.35-41
• /
• 2011

In concrete structural design provisons, two methods are normally provided to control deflection; direct method and indirect method. It is more efficient to use the indirect deflection control by which the span/depth ratio is limited not to exceed an allowable deflection limit. Because actual deflections are affected by many causes, it is complicated to evaluate actual deflections. In this study, limit span/depth ratios are derived from the deflection calculated directly at the serviceability limit state in RC members. The deflection is obtained from using average curvature, which depends on materials model used. The main variables examined are tension stiffening effect, concrete strength, cross section size and compressive steel ratio. It could be appeared that more analytical consistency is secured to use the 2nd order form of tension stiffening effect. And the limit span/depth ratio is dependent on material strength, tensile and compressive steel ratio but it is independent on cross-section size.

• Journal of the Society of Naval Architects of Korea
• /
• v.31 no.3
• /
• pp.119-128
• /
• 1994

Deflection estimation at engine room upper deck panel is performed for the actual ship structure. These deflection behaviours are basically investigated from not only the data based on the full series results of nonlinear analysis using Incremental Galerkin's Method but also actual deflection data measured from damaged ship under construction in dry dock. The effects of residual stress, initial deflection and static loading are also included. The computed estimation results of upper deck plate panel including theme effects are shown that upper deck platings of new ship expected less deflection magnitude than damaged ship.

• International Journal of Highway Engineering
• /
• v.8 no.3 s.29
• /
• pp.155-162
• /
• 2006

Deflections of jointed concrete pavements at test road are monitored during 48 hours. And methods of calibration with respect to curling deflections are suggested. Relations between deflection ratio of center to joint at test time and deflection ratio of center at test time to center at reference time are described by regression. From deflections at test time, deflections transformed to reference time which gives minimum deflections in a day are estimated through regression curves and concluded to propose as a alternative method of curling calibration with more data accumulation.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.6-9
• /
• 2011

지속하중을 받는 철근콘크리트 휨부재는 크리프, 건조수축 등 장기거동에 의하여 처짐이 증가된다. ACI318-08, KCI 2007 등 현행 구조설계기준의 장기처짐 평가방법은 인장 및 압축 철근비, 배근상세, 재료 강도 등 설계변수에 따른 장기처짐의 변화를 합리적으로 고려하기 어렵다. 본 연구에서는 장기거동에 의한 힘의 평형조건과 변형률 적합조건을 사용하여 크리프와 건조수축에 의한 철근콘크리트 균열단면의 장기변형을 예측하는 간략 평가식을 제안하였다. 장기변형 평가 시 콘크리트와 철근은 선형탄성거동을 가정하였고, 시간에 따른 콘크리트와 철근 사이의 응력재분배를 고려하기 위하여 재령보정탄성계수법을 적용하였다. 변수연구 및 검증 결과, 철근콘크리트 휨재의 장기처짐은 설계변수의 영향으로 달라질 수 있고, 제안된 방법은 이러한 장기처짐의 변화를 비교적 정확하게 예측하는 것으로 나타났다.

• Journal of the KSME
• /
• v.20 no.4
• /
• pp.296-302
• /
• 1980

이상에서 potential energy의 극소조건을 각종경우에 적용하여 재료역학의 해 또는 변형의 근사 해를 응용 예들을 통하여 구해 보았다. 이 해법은 을 받은 부재, 보(beam) 또는 순수 비틀림을 받는 엔형봉재의 경우, 부정정 문제에서 그 지지점들에서의 반력요소를 생각할 필요가 없기 때 문에 재료 역학적인 해법보다 더 간편하게 구해지고 있는 것을 볼 수가 있다. 또 보의 처짐 곡 선이 길이의 중앙면에 대하여 좌우 대칭형일 때에, 중앙단면에서의 최대처짐을 구하는데 삼각 함수의 근사처짐 곡선을 설정하므로써 실제 엄밀해에 가까운 근사값이 간단하게 구해질 수 있는 것을 보였다. 이 극소에너지 정리는 엔형단면이 아닌 각종 단면봉재의 비틀림 문제에서도 비틀림 응력함수를 도입하고, 경제조전을 만족하는 근사공력 함수방정식을 가정함으로써 간단하게 그 근사해를 구하는 데까지 직장할 수가 있다.

• Proceeding of EDISON Challenge
• /
• 2015.03a
• /
• pp.201-206
• /
• 2015

이 논문에서는 역학적 지식파 EDISON 구조동역학 서버에서 지원하는 이공계 교육 및 연구용 시뮬레이션 프로그램 중 Co-rotational Plane Beam with Arbitrary Section을 이용하여 캔틸레버 보의 처짐을 기하 비선형적으로 해석한다. 또한 해석에 사용된 프로그램이 실제 교육에 적용이 가능한 지를 고찰함에 그 목적이 있다. 처짐을 해석하기 위하여 수계산, 프로그램을 이용하여 얻은 결과값을 비교하였고 캔틸레버 보의 변화 형상을 시각화 하였다.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.6
• /
• pp.738-745
• /
• 2014

In this paper, It is performing to the elastic and elasto-plastic large deformation series analysis using a numerical method for the initial deflection effect of the aluminum alloy rectangular plate in the elasto-plastic loading area patch loading size. It is assumed a boundary condition to be a simply supported condition and consider the initial deflection amplitude, aspect ratio. It examined the critical elastic buckling load and post-buckling behaviour of aluminium alloy A6082-T6 rectangular plate. It used a commercial program for the elastic and elasto-plastic deformation series analysis. If the initial deflection amplitude is smaller, the in-plane rigidity with increasing to load is reduced from the start and occurs significantly more increasing the amplitude. More higher the aspect ratio, the initial yield strength is gradually decreased, and the plate thickness thicker and occurs larger than the thin walled plate a reduction ratio of the initial yield strength of the patch loading size as 0.5.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2004.04a
• /
• pp.83-88
• /
• 2004

Recently, High Tensile Steel is adapt to thin plate on the steel structure and marine structure is used widely. It is possible for buckling happens great. Specially, Initial deflection of ship structure happens in place absence necessarily by heat processing of welding or cutting etc. This Initial Deflection is exerted negative impact when thin plate absence complicated nonlinear behaviour accompanied secondary buckling. As a result, must idealize initial deflection that occurrence is possible to endow stability and accuracy in the hull structure or marine structure and reflect in early structure design considering secondary buckling. Longi direction of compressive load interacts and analyzed finite element series analysis that apply various kinds initial deflection shape measured actually on occasion that is arranged simply supported condition in this research. Applied ANSYS (elasto-plasticity large deformation finite element method) to be mediocrity finite element program for analysis method and analysis control used in Newton-Raphson method ＆ Arc-length method.

• Computational Structural Engineering
• /
• v.5 no.1
• /
• pp.83-89
• /
• 1992

A practical method of estimating inelastic deflection of reinforced concrete slab under service load is presented. Based on the elastic results of linear finite element analysis and area of reinforcement, inelastic deflection multiplier(.betha.) is evaluated and desired deflection as a measure of serviceability of the designed slab is obtained. Example for the corner supported slab shows that the results from the proposed method agree well with those from the experiment/and nonlinear finite element analysis. Application of the method to the design of irregular slab is also considered.

• Journal of Korean Society of Steel Construction
• /
• v.18 no.5
• /
• pp.563-574
• /
• 2006

The objective of this study is to determine the effect of the loading size on displacements of stiffened plates with open ribs using the orthotropic rigidity ratio as the parameter. To analyze the displacement behavior of stiffened plates according to the loading size, a concentrated load and three types of uniform distributed loads were applied on the rib at the center of some plates. The results of the analysis of various stiffened plates show that the central displacement ratio of the distributed load to the concentrated load increased according to the decrease in the loading size, and that the ratio can be expressed as a function of the rigidity ratio for each rib space. The maximum displacement of the stiffened plate subjected to the distributed load did not appear at the center of the plate due to the local behavior, and the increasing ratio of the maximum displacement to the central displacement can be expressed as a function of the rigidity ratio for each rib space. Orthotropic plate analysis can achieve more accurate results using the proposed functions, and the application of the functions to examples of a different aspect ratio and support condition shows good accuracy. Therefore, using the functions proposed in this study, the central and maximum displacements can easily be achieved in the orthotropic plate analysis of stiffened plates subjected to the distributed load.