• Journal of Korean Society of Transportation
• /
• v.19 no.6
• /
• pp.143-160
• /
• 2001

Micro-simulation models have been recognized as an efficient assessment tool in developing traffic signal control technologies. In this paper a prototype of a microscopic simulation model which can be applied to evaluate the performance of traffic-adaptive signal control strategies was developed. In the simulation process, space-based arrays were appled to estimate parameters of car following and lane changing models. Two levels of link types, a micro-type and macro-type links, were also embodied in the simulation process. The proposed model was tested on a test network consists of 9 intersections. The performance of the proposed model was evaluated in link by link comparisons with the results of NETSIM. The results show that the proposed model could appropriately simulate traffic flows of the test network. The model also produces traffic adaptive signal timings, cycle lengths and green times for turning movements, based on the detector data. It implies that the optimization process of the model produces reasonable signal timings for the test network on the cycle basis.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.11 no.6
• /
• pp.31-39
• /
• 2012

This study aims to suggest a methodology of localizing and calibrating parameters, such as acceleration, deceleration, and lane changing which are the basis of car following model in interrupted traffic flow to overcome the limitation of origin and destination based transportation simulation and to verify the application of activity-based model for use in Korean roadway condition in a large scale area or a city. Especially, we figured out that a proper cell size reflecting Korean traffic conditions is 1.0m rather than 7.5m which is default size and a methodology of tracking vehicle behavior characteristics through tracking vehicle ID is suggested on this study. In addition, vehicle running characteristics in real interrupted traffic flow is analyzed through subdividing vehicle types and updating vehicle type ratio. For verification of suggested model, some portion of Dalgubyul-ro in the Daegu city is tested, and the possibility of realization of interrupted traffic flow in simulation is studied.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.38 no.6
• /
• pp.879-885
• /
• 2018

The highway weaving section is a point where there is a conflict caused by entry and exit vehicles. In order to minimize the impact on the main line, an accumulation line should be installed. The design speed of the collecting part is 50 km/h, but the actual driver does not have proper deceleration according to the design speed. In this study, considering the driving behaviors, the design specification, and the driver 's viewing angle, the appropriate separation distance for safe entry and exit of collecting, connecting, and collecting roads was examined. As a result of the analysis, it is found that a distance of 60m is required from the point where the merging starts. The results of this study are expected to contribute to the improvement of driver safety due to the conflict between entry and exit vehicles when applied to the weaving section where collecting roads are installed.

• Korean Journal of Culture and Social Issue
• /
• v.12 no.4
• /
• pp.37-53
• /
• 2006

This study examined the perception of driving ability of drivers under stressful situation and it attempted to collect the base data in an effort to prevent the traffic accidents by the women drivers. For this purpose, 180 drivers residing in the Seoul and Gyeonggi region were selected to find out how they perceive their driving ability and driving ability of the others, and in particular, study was focused on in what kind of situation female drivers felt most stress out. Looking in relation to the driving ability, female drivers tend to assess overly high on driving ability of male drivers while making excessively low on the abilities of other female drivers. Looking into the stress of female drivers while driving, the female drivers experience more stress during driving compared to the male drivers. This type of result indicates that the women lack the confidence on driving abilities while experiencing severe stress on the driving performance.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.2 no.1 s.2
• /
• pp.25-40
• /
• 2003

The purpose of this thesis is development of detection algorithm for stop-line detector. Detail detection area is set in basing detection area($1.8{\times}4.0m$) and traffic information(volume, occupancy, nonoccupancy) is collected by passive infrared detector at designing detection area. The basis detection area($1.8{\times}4.0m$) is named existing PIR and detection area applied on development algorithm is named proposal PIR. The proposal PIR is collected data such volume, occupancy, nonoccupancy, speed and lane change, but this thesis is limited to evaluate for volume, occupancy and nonoccupancy The procedure and each step of being developed algorithm is described in the next (1) The detection area of proposal PIR is made up of 2 of $1.8{\times}0.6m$ size(the detection area is named 1 and 3) and 1 of $1.8{\times}1.78m$ size(the detection area is named 2) (2) The image detection area is set on monitor to analyze outdoor photographing data then video frame analysis has been done by analyzer. (3) The occupancy, nonoccupancy and speed data of vehicle have been collected with the detection area 1 and 3 and lane change has been collected with combination of detection area 1, 2 and 3 The MAD and MAPE have been utilized to being compared with volume, occupancy and nonoccupancy for the field application and evaluation of a algorithm As the result, the proposal PIR data have been identified superior to the existing PIR data and the effect has been improved its information(volume, occupancy and nonoccupancy)

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.1D
• /
• pp.25-32
• /
• 2009

Currently, various types of TDM (Transportation Demand Management) policies are being studied and implemented in an attempt to overcome the limitations of supply oriented policies. In this context, this paper addressed issues of effectiveness and possible domestic implementation of the HOT lane. The possible site of implementation selected for this simulation study is part of the Kyung-bu freeway, where a dedicated bus lane is currently being operated. Minimum length of distance required in between interchanges and access points of the HOT lane for vehicles to safely enter and exit the lane, and traffic management policies for effectively managing the weaving traffic trying to enter and exit the HOT lane were presented. A 5.2km section of freeway from Ki-heuing IC to Suwon IC and a 8.3km section from Hak-uei JC to Pan-gyo JC have been selected as possible sites of implementation for the HOT lane, in which congestion occurs regularly due to the high level of travel demand. VISSIM simulation program has been used to analyze the effects of the HOT lane under the assumption that one-lane HOT lane has been put into operation in these sections and that the lane change rate were in between 5% to 30%. The results of each possible scenario have proven that overall travel speed on the general lanes have increased as well by 1.57~2.62km/h after the implementation of the HOT lane. It is meaningful that this study could serve as a basic reference data for possible follow-up studies on the HOT lane as one effective method of TDM policies. Considering that the bus travel rate would continue increase and assuming the improvement in travel speed on general lanes, similar case study can be implemented where gaps between buses on bus lane are available, as a possible alternative of efficient bus lane management policies.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.16 no.6
• /
• pp.79-89
• /
• 2017

Current intersection with collectors allow entry and exit in the relevant sections just as defined by the pertinent design criteria without considering driving behavior of the vehicles coming in and out of the intersection. This study analyzed the roads in the weaving sections to review driving behavior. As a result, vehicles entering a main line are found to try to change a driving lane at a section 50~55m away from a nose part, while those entering a ramp from a main line try to change it at 35~40m from a nose part. Accordingly vehicles exiting to a connecting road from a main line were found to take prior action to change a lane earlier than those entering a main line. Conflict took place intensively at 35~40m section from the nose part entering a main line. Consequently, such conflict at an weaving section may be controlled by adjusting the length of driving lane making use of a double line (solid and dotted line) that can control changing a lane. Outcome of this study may be used as a basic data for operating and maintaining an weaving section of a intersection of a road and improving traffic safety.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.1D
• /
• pp.41-48
• /
• 2009

The capacity analysis of signalized intersection usually includes a HCM method used at home and abroad and a ICU method this study presents. The HCM method focuses on operation analysis measuring an intersection's delay in terms of given traffic volume, signal operation, and intersection structure data. This method includes planning and design analysis, but these analyses are complex due to being possible through repetitive operation analysis. However the ICU method is a powerful tool for planning and design analysis, because these are possible through brief traffic volume and geometry structure data and consider minimum green time. In this study, the authors studied the ICU method and compared the HCM and ICU by analyzing traffic volume scenarios. Also to consider effectiveness for application of the ICU method, the authors applied the ICU to capacity analysis of intersections on urban arterial for setting major intersection and effect analysis for changing crosswalk type, the number of lane, lane use and operation form of left turn. The result of the analyses shows that the ICU method can measure correct capacity of intersection consist of a broad road in urban area, and is effective for planning and design analysis. This study is expected that traffic experts can grasp correct intersection's capacity and carry out a proper planning or improvement by applying the ICU method to planning and design analysis.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.22 no.5
• /
• pp.148-162
• /
• 2023

The objective of this study is to derive the appropriate perception location for changes in driving behavior of autonomous vehicles in urban road environments based on traffic safety signs. For this purpose, 32 types of signs that induce changes in driving behavior were selected from currently used traffic safety signs and classified as three types according to changes in driving behavior. Based on this, three scenarios were designed: stop, speed change, and lane change scenarios. These were used to confirm the impact on traffic flow. As a result of the analysis, it was found that each scenario needs to receive information on traffic safety signs in advance to ensure changes in traffic flow and safety. Consequently, the appropriate perception location can be used as a basis for establishing standards for delivering message sets to autonomous vehicles or revising traffic safety signs for them. In addition, this study is expected to contribute to the establishment of safe and efficient driving strategies on urban roads as autonomous vehicles are introduced in the future.

• International Journal of Highway Engineering
• /
• v.13 no.3
• /
• pp.195-202
• /
• 2011

The purpose of this study is to estimate the capacity of two-lane freeway work zone blocking one lane using traffic flow models of each vehicle-type. Firstly, three traffic flow models of three different vehicle-types were developed using the data collected from each at the beginning and the ending point of the work zone. For each model, the maximum flow rate of three vehicle-types were calculated respectively. Maximum flow rate at the work zone was recalculated using passenger car equivalent value and percentage of vehicle-type. Secondly, traffic flow model using passenger car equivalent volume data was developed using the data collected from each at the beginning and the ending point of the work zone. Maximum flow rate for the work zone was calculated along. Two values of maximum flow rates through the work zone were compared and evaluated as the capacity of the work zone. This study found that the maximum flow rate of the work zone at the beginning point was less than that at the ending point because of impedance such as lane changing behaviors before entering the work zone. The capacity of two-lane freeway work zone blocking one lane was estimated 1,800pcphpl.