• Journal of the Korean Association of Geographic Information Studies
• /
• v.4 no.3
• /
• pp.51-60
• /
• 2001

The travel behavior can be analysed microscopically using GPS because the travel characteristics can be found out by travelling two test cars loaded with GPS equipments. The speed difference and spacing variation between the lead vehicle and the following's in uninterrupted flow are the important variables related to capacity and safety. This study analysed these with data obtained by travelling the 4th Line and 28th Line of the national road. The variation width in speed difference in the run time is below 3.0%. But, related to the speed difference in the situation of acceleration and deceleration the difference after 4second is bigger than that just after the start. The spacing variation is similar to this. The spacing just before deceleration concerning safety was analysed. When the theoretical values by the modeling method and observed values were compared, the observed values were analysed 12.52% shorter than the other in average.

• Journal of Korean Society of Transportation
• /
• v.19 no.6
• /
• pp.195-205
• /
• 2001

The objective of the paper is to analyze the traffic characteristics for freeway merging area. Freeway merging area is different from basic section due to ramp vehicles. Therefore, to understand the traffic characteristics of (leeway merging area, this study focused on two factors including critical time headway required in merging maneuver and maximum possible merging volume. In this paper, new model that adopts critical time headway instead of critical time gap in calculating the maximum possible merging volume based on probability function was developed In previous studies, for calculating the maximum possible merging volume, it was considered that merging vehicles could merge freely if a given time gap was greater than the critical time gap. Also, the critical time gap was used as the same value in all traffic flow conditions. But, a time gap required in merging maneuver could be changed, even to the same driver, because difference of relative speed varies in different traffic flow conditions. So, in some cases, the critical time gap could be insufficient value in merging maneuver. Therefore, in this study. a calculating procedure for critical time headway in all traffic flow conditions was presented. Also, the maximum possible merging volume and capacity for freeway merging area were calculated by using the previously found critical time headway.

• Journal of Korean Society of Transportation
• /
• v.27 no.6
• /
• pp.119-127
• /
• 2009

It has been known that bus route and company related characteristics have influences on punctuality, but fewer research have been conducted. Independent variables used in this study were selected using correlation analysis, and OLS(Ordinary Least Square) and HLM(Hierarchical Linear Model) were employed to identify factors affecting bus punctuality(headway deviation). The results showed that ICC(intraclass Correlation Coefficient) is 0.10, indicating that hierarchical linear models are more adequate for these data because there is effective variation in the subjects between companies. Punctuality was found to be negatively associated with the number of vehicles, the number of persons per vehicle, and total travel time. On the other hand, average headway and company size have a positive relationship with punctuality. Therefore, the number of vehicles per route, average headway, and the number of vehicles managed by a company should be considered for more accurately evaluating the management of piunctuality.

• Journal of Korean Society of Transportation
• /
• v.16 no.4
• /
• pp.113-126
• /
• 1998

본 논문에서는 1992년 KHCM 작성시 이용된 양방향 2차선 도로 및 고속도로의 승용차 환산계수 산정방법론 및 자료를 연구하였다. 대형차가 2차선도로, 고속도로의 교통류에 미치는 영향은 각기 다르므로 1992년 KHCM 작성시 승용차 환산계수를 산정하는데 있어서 각 도로의 특성을 최대한 반영하기 위해 다양한 방법을 적용하였다. 양방향 2차선 도로의 평지의 서비스 수준 A에서는 Walder 방법, 서비스 수준 B, C, D에서는 지체시간 방법, 서비스 수준 E에서는 차두간격 방법, 구릉지, 산지 특정구배에서는 실측 자료 및 TWOPASKI Simulation에 의한 방법을 적용하였고, 고속도로의 평지에서는 차두간격 방법, 그릉지, 산지, 특정구배에서는 실측 자료 및 VEHEQ Simulation에 의한 방법을 적용하였다. 양방향 2차선 도로는 한 방향당 차선이 하나이므로 추월시 대형차의 영향이 고속도로보다 크기 때문에 각 서비스 수준별고 승용차 환산계수를 제시했으며, 고속도로의 승용차 환산계수는 용량에 가까운 상태에서의 승용차환산계수를 제시하였다. 본 논문은 1992년 KHCM의 양방향 2차선 도로 및 고속도로의 승용차 환산계수 산정에 실지로 적용된 방법론 및 자료를 수정없이 그대로 제시하여 독자들이 승용차 환산계수 산정에 이용된 자료의 양 및 연구 수준의 정도를 이해할 수 있게 하고 독자의 평가를 통하여 미비한 부분은 추후 개정 작업에 반영하기 위함이다.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.23 no.1
• /
• pp.82-96
• /
• 2024

While analyzing traffic flow, speed, traffic volume, and density are important macroscopic indicators, and acceleration and spacing are the important microscopic indicators. The speed and traffic volume can be collected with the currently installed traffic information collection devices. However, acceleration and spacing data are necessary for safety and autonomous driving but cannot be collected using the current traffic information collection devices. 'You Look Only Once'(YOLO), an object recognition technique, has excellent accuracy and real-time performance and is used in various fields, including the transportation field. In this study, to measure acceleration and spacing using YOLO, we developed a model that measures acceleration and spacing through changes in vehicle speed at each interval and the differences in the travel time between vehicles by setting the measurement intervals closely. It was confirmed that the range of acceleration and spacing is different depending on the traffic characteristics of each point, and a comparative analysis was performed according to the reference distance and screen angle to secure the measurement rate. The measurement interval was 20m, and the closer the angle was to a right angle, the higher the measurement rate. These results will contribute to the analysis of safety by intersection and the domestic vehicle behavior model.

• Journal of Korean Society of Transportation
• /
• v.22 no.2 s.73
• /
• pp.103-108
• /
• 2004

The motivation of this study comes from the problem recognition that the headway of passing vehicle in signalized intersections can not be merely determined by departing sequence. Traffic speed and headway data of passing vehicles in signalized intersection have been obtained by using magnetic detectors(NC 97) and detecting program, and the data was analyzed. Without special treatment, the model established on passing behavior of vehicles was meaningless from statistical view point. Hence, special treatments such as filtering (upper 85% offensive driver driven vehicle's) and log scaling of data were carried on. With this new data, meaningful model (where coefficient of determination is 0.91) was established. This model explained the fact that vehicle headway in signalized intersection is affected by speed and headway of previous vehicle and speed of itself.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.9 no.1
• /
• pp.1-10
• /
• 1989

The stress history of a bridge is different depending on the characteristic of traffic flow. Because the flow is varied with vehicle type, weight and headway time etc., statistical analysis in bridges is necessary to estimate the history by traffic flow. By applying the statistical analyses in fracture mechanics, the remaining service life of the structure can be estimated. In this paper, 1)the statistical analysis of vehicle type, weight and headway time etc. to analysis randomness of traffic flow, 2)measuring and analysis of stress history of a real bridge, 3)reappearance of stress history by Monte-Carlo Simulation using constitution ratio of vehicle type, weight and headway time as probabilitic variable, 4)comparision of the calculated and modelled stress history, 5)calculation of reduction factor, 6)comparision of frequency of stress range depending on span length etc. were performed. From the results, the basic modelled stress history which is necessary for the method of estimation of the remaining service life of the structure could be suggested.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.18 no.5
• /
• pp.79-90
• /
• 2019

This study aims to develop time headway distribution models of bicycle traffic flow in a uninterrupted bikeway. The sample data were collected and classified into two groups of traffic volume levels. The lower level traffic volume is defined to be under 8 bicycles per minute, and the higher one is greater or equal to 8 bicycles per minute. The data aggregation interval size was set to be 0.5-second. Four distribution models including normal distribution, negative exponential distribution, shifted negative exponential distribution, and Pearson III distribution were tested, and Chi-square test results shows that the negative exponential distribution and the shifted negative exponential distribution are well fitted to the sample data. Another test results with different sample data also shows the same conclusion.

• Journal of Korean Society of Transportation
• /
• v.21 no.3
• /
• pp.107-120
• /
• 2003

Over the decades, a lot of studies have dealt with the traffic characteristics and phenomena at a merging area. However, relatively few analytical techniques have been developed to evaluate the traffic flow at the area and, especially, the ramp merging capacity has rarely been. This study focused on the merging behaviors that were characterized by the relationship between the shoulder lane flow and the on-ramp flow, and modeled these behaviors to determine ramp merge capacity by using gap acceptance theory. In the process of building the model, both an ideal mergence and a forced mergence were considered when ramp-merging vehicles entered the gap provided by the flow of the shoulder lane. In addition, the model for the critical gap was proposed because the critical gap was the most influential factor to determine merging capacity in the developed models. The developed models showed that the merging capacity value was on the increase as the critical gap decreased and the shoulder lane volume increased. This study has a meaning of modeling the merging behaviors including the forced merging type to determine ramp merging capacity more precisely. The findings of this study would help analyze traffic phenomena and understand traffic behaviors at a merging area, and might be applicable to decide the primary parameters of on-ramp control by considering the effects of ramp merging flow.

• Proceedings of the KOR-KST Conference
• /
• 1998.10b
• /
• pp.297-297
• /
• 1998

고속도로의 교통혼잡을 관리하기 위해서는 근본적으로 혼잡지점 상류부의 진입교통량을 제어해야 한다. 이를 위한 효과적인 램프미터링 운영전략이나 고속도로 교통정보제공방안을 수립하기 위해서는 혼잡영향권(대기행렬길이)에 관한 신뢰성 있는 데이터가 반드시 필요하다. 고속도로의 대기행렬길이를 산정하기 위해 일반적으로 충격파이론과 Queueing이론을 제시하고 있다. 그러나, 기존의 충격파 이론을 포물선형의 교통량-밀도관계식을 근거로 하고 있어 충격파간에 발생하는 부수적인 충격파를 해석하는 과정이 수학적으로 불가능하여 실질적인 목적으로 사용할 수 없음은 이미 잘 알고 있는 사실이다. 최근에 이러한 한계를 극복할 수 있는 새로운 방법으로 교통량 밀도간의 관계식을 삼각형으로 가정하고 교통량 대신에 누적교통량을 사용하는 Simplified Theory of Kinematic Waves In Highway Traffic이 개발(Newell, 1993)되었지만, 이 방법을 적용하기 위해서는 기본적으로 대상 고속도로 구간의 교통량-밀도관계식을 규명해야 하는 어려움이 있다.(사실 실시간으로 밀도데이터를 수집하기란 불가능하다.) Queueing이론에서 제시하는 대기행렬은 모두 대기차량이 병목지점에 수직으로 정렬하여 도로를 점유하지 않는 Point Queue(혹은 Vertical stack Queue)로서 실제로 도로상에 정렬된 대기행렬(Real Physical Queue)과는 전혀 다르다. 이미 입증된 바 있어, Queueing이론을 이용함은 타당성이 없다. 이러한 사실에 근거하여 본 연구는 고속도로 대기행렬길이를 산정할 수 있는 모형개발을 위한 기초연구로서 혼잡상태의 연속류 특성을 분석하는데 목적이 있다. 이를 위해, 본 연구에서는 서울시 도시고속도로에서 수집한 실제 데이터를 이용하여 진입램프지점의 혼잡상태에서 대기행렬의 증가 또는 감소하는 과정을 분석하였다. 주요 분석결과는 다음과 같다. 1. 혼잡초기의 대기행렬은 다른 혼잡시기에 비해 상대적으로 급속한 속도로 증가함. 2. 혼잡초기의 대기행렬의 밀도는 다른 혼잡시기에 비해 비교적 낮음. 3. 위의 두 결과는 서로 관계가 있으며, 혼잡시 운전자의 행태(차두간격)과 혼잡기간중에도 변화함을 의미함. 4. 교통변수 중에서 대기행렬길이를 산정하는데 적합한 교통변수를 교통량과 밀도로 판단됨. 5. Queueing이론에서 제시하는 대리행렬길이 산정방법인 대기차량대수$\times$평균차두간격은 대기행렬내 밀도가 일정하지 않아 부적합함을 재확인함. 6. 혼잡초기를 제외한 혼잡기간 중 대기행렬길이는 밀도데이터 없이도 혼잡 상류부의 도착교통량과 병목지점 본선통과교통량만을 이용하여 추정이 가능함. 7. 이상에 연구한 결과를 토대로, 고속도로 대기행렬길이를 산정할 수 있는 기초적인 도형을 제시함.