• The Journal of Engineering Geology
• /
• v.28 no.3
• /
• pp.411-429
• /
• 2018

Daeyoung mine (also called "Daema mine") produced gold and silver from mainly gold- and silver-bearing quartz veins. The mine tailings are a waste hazard, but most of the tailings were swept away or dispersed throughout the area around the mine long before the tailing dump areas were transformed into agricultural land. Soil liner and protection facilities, such as retaining walls, were constructed in the mine area to prevent the loss of tailings. The content of the tailings is 3,424.41~3,803.61 mg/kg, which exceeds the safety standard by a factor of 45. In addition, contamination was detected near agricultural areas and in the sediments in downstream drainage channels. A high level of As contamination was concentrated near the waste tailings yard; comparaable levels were detected in agricultural areas close to streams that ran through the waste dump yard, whereas the levels were much lower in areas far from the streams. The contamination in stream sediments showed a gradual decrease with distance from the mine waste yard. Based on these contamination patterns, we concluded that there are two main paths that affect the spread of contaminants: (1) loss of mine waste, and (2) the introduction of mine waste into agricultural areas by floods after transportation by streams. The agricultural areas contaminated by mass inflow of mine waste can act as contamination sources themselves, affecting other agricultural areas through the diffusion of contaminants. At present, although the measured effect in minimal, sediments in streams are contaminated by exposed mine waste and surface liners. It is possible for contaminants to diffuse or spread into nearby areas if heavy elements trapped in soil grains in contaminated agricultural areas leach out as soil solution or contaminant particles during diffusion into the water supply.

• Economic and Environmental Geology
• /
• v.43 no.3
• /
• pp.235-248
• /
• 2010

To construct the standard methods for evaluation of physicochemical characteristics of tailings in Korea, specific gravity, paste pH, grain size, mineral compositions and heavy metal concentrations of total 26 tailings from 21 metallic mines were analyzed. Specific gravity of tailings ranged from 2.61 to 4.31 (avg. 3.04), and sand and silt grain were dominant in the tailings. Ranges of paste pH were 2.1-9.5 in tailings (7.1-9.2 at magmatic, skarn and hydrothermal replacement deposits and 2.1-9.5 at hydrothermal vein deposits). Additionally, hydrothermal vein deposits could be reclassified into three categories: (1) paste pH>7.0, (2) 4.0

• Economic and Environmental Geology
• /
• v.53 no.4
• /
• pp.337-346
• /
• 2020

This study was carried out to evaluate the applicability of the soil washing process to remediation mercury-contaminated mine tailing or solid material (soil and sediments etc.) around abandoned mines. First, the physicochemical characteristics of mine tailing were analyzed through particle size analysis and sequential extraction. Secondly, laboratory scale washing experiments were performed using hydrochloric acid, nitric acid, potassium iodide and sodium thiosulfate. As a results of particle size analysis, mine tailing particle were concentrated below 40 mesh and the particle size below 200 mesh was the most analyzed. As a result of sequential extraction, elemental mercury fraction was analyzed as the highest with 69.12%, with strongly bound fraction 15.25% and residual and HgS fractions 11.97%, respectively. Laboratory scale washing experiments showed low applicability for nitric acid and sodium thiosulfate solutions. In case of hydrochloric acid solution, it was analyzed that mercury removal was possible at particle size of 200 mesh or more. Therefore, it is considered to be performed together with the physical sorting process. Potassium iodide solution was analyzed to have high washing efficiency at all concentrations and particle sizes. In particular, the mercury removal efficiency is high in the micro particles, and thus the applicability of the washing technology is the highest.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1995.10a
• /
• pp.36-37
• /
• 1995

투과증발법은 기존의 증류법에 의해 분리되기 어려운 혼합물(공비혼합물이나 끓는점이 비슷한 혼합물)이외에 열에 민감한 생성물의 분리, 과익쥬스의 농축, 불순물 찌꺼기의 제거, 정량 검출을 위한 유기 오염물질의 농축 등에 이용되었으며 특히 물과 에탄올의 공비혼합물의 분리와 물로부터 희박 유기물질을 회수하는데 행해져 왔다. 본 연구에서 사용된 키토산은 친수성기들을 가지고 있기 때문에 물과 알코올의 분리에서 물을 선택적으로 투과시켜 효과적인 투과증발막으로 사용될 수 있으며 투과속도를 높이기 위해서 활성층이 매우 얇은 복합막을 제조하였다. 또한 키토산 복합막을 다양한 가교제 (glutaraldehyde, glyoxal, terephthalaldehyde, 황산등)로 가교한 막들을 열처리를 하거나 키토산과 PVA를 블렌드하여 제조한 키토산/PVA 블렌드 복합막을 이용하여 에탄올/물, IPA/물 혼합용액에서의 탈수 실험을 실시하여 이에 따른 투과성능의 영향을 살펴보았다.

• Journal of ILASS-Korea
• /
• v.20 no.2
• /
• pp.95-100
• /
• 2015

Lower recirculated gas temperature at EGR system reduces NOx and PM emissions. However, EGR Cooler can be polluted by PM generated from recirculated EGR gas, and it reduces cooling efficiency and the amount of EGR gas simultaneously. The SECFR(Steam EGR Cooler Fouling Remover) system which uses the evaporated washer fluid steam caused by high temperature of EGR gas was manufactured for removing fouling generated on the cooler surface. Since an injection pressure of wind shield washer fluid in the vehicle is approximately 0.5 bar, it is not enough to atomize the injected washer fluid. Thus, it is necessary to apply a method to atomize the washer fluid. In this study, the impinging plate was used to promote the atomization of spray washer fluid for the purpose of apply SECFR system to vehicles and measured the DAR(Droplet Area Ratio) and DUI(Droplet Uniformity Index) through the spray visualization.

• Resources Recycling
• /
• v.22 no.5
• /
• pp.43-49
• /
• 2013

Froth flotation was performed to remove As from the tailing of Sangdong Mine. When the tailings of Sangdong Mine were analyzed by the Standard Method for the Soil Environment Conservation, the concentration of As was found to be at a serious level (282 mg/kg), exceeding countermeasure standard (75 mg/kg). Froth flotation was performed to remove As and preliminary tests were performed to select the reagents. Specifically, froth flotation was performed using collector and frother, KAX and DF250 respectively. An experiment based on pH changes found that the removal rate was highest at pH6. The removal rate of As was highest at agitating rate 1500 according to the agitating rate. In the experiment based on the quantities of KAX added, the removal rate of As was found to be highest at 300 g/ton and was reduced at higher levels than 300 g/ton. An experiment based on pulp density found that the removal rate was highest at pulp density 30%. It was possible to adjust the As level -- which exceeded countermeasure standard (75 mg/kg) -- to 22.5mg/kg to satisfy the Warning standard (25 mg/kg), from the results of froth flotation.

• Journal of Marine Life Science
• /
• v.4 no.2
• /
• pp.86-90
• /
• 2019

This study aimed to compare the disinfection efficiencies of the ultraviolet and plasma systems, the two systems designed and commercialized to disinfect water in aquaculture, by putting each in a 100 ℓ water tank and concentrating 1.0 ℓ of treated water to check the changes in the number of bacteria in the samples. Each system was operated for 6 hours to culture the typical seawater bacteria in the Marine agar, Thiosulfate citrate bile salts sucrose agar and Salmonella Shigella agar media, respectively, to check the number of bacteria in the media, and the changes in the number of Edwardsiella piscicida in the treated water were checked after the artificial inoculation of E. piscicida in the disinfected seawater. As a result, the two disinfection systems showed the almost similar levels of bacterial reduction efficiency between 99.5% and 99.9%. However, the result of this study showed that, with 100 ℓ of water treated for the same length of time using the two systems, the plasma system turned out to disinfect bacteria in a shorter period of time than the UV system. However, as the changes in the number of bacteria were checked for a short length of time (6 hours) in this study, it was judged that, considering the actual aquaculture environment in which the quality of water significantly changes with feed residues, excretions and coastal contamination, etc., and a lot of biofilms and organic matter exist, the plasma system would be more efficient than the UV system as the former is capable of continuously maintaining a certain level of efficiency than the latter that is limited in terms of efficiency depending on the level of turbidity and the existence of organic matter.