• Nuclear Engineering and Technology
• /
• v.20 no.1
• /
• pp.1-8
• /
• 1988

During power plant operation, the flow rate from the CVCS makeup system is estimated using the continuity equation and mass balance equation, when the primary loop boron concentration change is required due to the power transient. For this purpose, primary loop, pressurizer and VCT(volume control tank)(in CVCS) are modeled by three control volumes which contain each mass and boron concentration. Connecting pipes between primary loop, pressurizer and CVCS are also modeled by time delay. Calculation for 14-2-6-2 (power 100-50-100) load follow case (at EOL, for KNU 7) is made using these models.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2001.11a
• /
• pp.317-318
• /
• 2001

PM$_{10}$ 대기먼지는 자연적이고 인위적인 발생원에 의해 다양한 미량원소들을 함유하고 있기 때문에 흔히 대기질이나 환경영향 평가를 위한 대기관측시료로 이용되고 있으며, 특히 PM$_{2.5}$ 먼지의 질량농도와 특정원소의 농도가 높을 때, 장\ulcorner단기적으로 인체 보건에 큰 영향을 미치는 것으로 알려져 있다. 중성자 방사화분석법은 핵반응을 통해 생성시킨 방사성동위원소로부터 방출되는 방사선을 검색하여 절대적으로 성분원소를 정량하는 핵분석기술(Nuclear Analytical Techniques)중의 하나로서 소량의 시료로부터 미량 원소의 비파괴, 동시 다원소 분석이 가능하고 분석감도($10^{-3}$ - $10^{-7}$$\mu\textrm{g}$)가 탁월한 분석기술이다. (중략)략)

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2002.04a
• /
• pp.269-270
• /
• 2002

PM$_{10}$ 대기먼지는 자연적이고 인위적인 발생원에 의해 다양한 미량원소들을 함유하고 있기 때문에 흔히 대기질 관리나 환경영향 평가를 위한 대기관측시료로 이용되고 있으며, 특히 PM$_{2.5}$ 먼지의 질량농도와 특정원소의 농도가 높을 때, 장ㆍ단기적으로 인체 보건에 큰 영향을 미치는 것으로 알려져 있다. 중성자방사화분석법은 핵반응을 통해 생성시킨 방사성동위원소로부터 방출되는 방사선을 검색하여 절대적으로 성분원소를 정량하는 핵분석기술(Nuclear Analytical Techniques)중의 하나로서 소량의 시료로부터 미량원소의 비파괴, 동시 다원소 분석이 가능하고 분석감도($10^{-3}$ - $10^{-7}$$\mu\textrm{g}$)가 탁월한 분석기술이다. (중략)략)

• Journal of Environmental Science International
• /
• v.24 no.6
• /
• pp.777-784
• /
• 2015

This study investigates weekday/weekend characteristics of $PM_{10}$ and $PM_{2.5}$ concentration and metallic elements in Busan in the springtime of 2013. $PM_{10}$ concentration on weekday/weekend were 77.54 and $67.28{\mu}g/m^3$, respectively. And $PM_{2.5}$ concentration on weekday/weekend were 57.81 and $43.83{\mu}g/m^3$, respectively. Also, $PM_{2.5}/PM_{10}$ concentration ratio on weekdays/weekend was 0.75 and 0.65, respectively. The contribution rates of Na to total metallic elements in $PM_{10}$ on weekday/weekend were 38.3% and 38.9%, respectively. It would be useful in control effectively with management of urban fine particle to understand characteristics of fine particle concentration on weekday/weekend.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.10a
• /
• pp.147-152
• /
• 2002

The mechanism of the aerosol(mist) generation generally consists of spin-off, splash, and evaporation/condensation. Host researchers showed some theoretical model for predicting the particulate size and generation rate without real cutting in turning operation. These models were based on the spin-off mechanism, and verified good for modeling the process. However, in real machining, the cutting tool destroys the flow direction of the cutting fluid and generate the heat by the relative motion of between tool and workpicee, and so the mass loading of the mist is greatly increased as compared with non-cutting. In this paper, we show some experimental data that the mist formation characteristics of cutting is different from that of non-cutting.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.819-820
• /
• 2012

• Analytical Science and Technology
• /
• v.16 no.3
• /
• pp.191-197
• /
• 2003

Two methods, IDMS (Isotope Dilution Mass Spectrometry) and controlled potential coulometry are compared by the determination of Pu for the NBL, CRM No.122, $PuO_2$. The recovery of Pu was found to be $1.002176{\pm}0.000452$ within the relative standard deviation of 0.045% (95% conf. level) although a small size of sample ($0.9{\mu}g$-Pu) was used in IDMS. The recovery using controlled potential coulometry were obtained in the range of 0.9923~0.9960. The analytical results of IDMS and controlled potential coulometry were good agreement within 0.6~1%. Base on these experiment results, The plutonium in HANARO irradiated fuel rod that separated portion of top, middle, and bottom were determined. The measured values of Pu are 1.155 mg, 2.483 mg and 1.920 mg in one gram of sample(fuel+clad), respectively.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.5
• /
• pp.103-111
• /
• 2022

Fine dust can cause serious problems to human health, and fugitive dust generated at construction sites is one of the main sources of fine dust in Korea. However, monitoring of the amount of fugitive dust generated at the ready-mixed concrete plant site is not performed, and only passive monitoring methods are partially applied in the field. Since it is impossible to control fugitive dust after it is exposed to the air, it is very important to suppress the occurrence or to remove it immediately at the stage of occurrence. Therefore, after identifying the characteristics through real-time monitoring in the fugitive dust generation stage, systematic management is required for suppressing or removing scattering dust in the field. In this study, the scattering dust generation characteristics were analyzed by measuring the particle mass concentration(PMC) of Fugitive dust generated at the aggregate unloading site of the ready-mixed concrete plant in real-time.

• The Journal of the Acoustical Society of Korea
• /
• v.26 no.1
• /
• pp.42-47
• /
• 2007

In this paper. we have studied improvement in sensitivity by increasing the frequency of SAW sensors for detecting the immobilization and hybridization of DNA. The sensor consists of twin SAW delay lines operating at 200MHz, a sensing channel and a reference channel. fabricated on $36^{\circ}$ rotated Y-cut X-propagation $LiTaO_3$ crystals. The optimum concentration of probe and target DNA was decided for the improvement of detection mechanism. and digital syringe pump system was used to reduce the human errors. The hybridization between immobilized probe DNA and target DNA on the gold-coated delay line results in mass loading on the delay line of the sensing channel. Thus, the relative frequency change was monitored in relation to the mass loading. The measurement results showed a good response of the sensor to the DNA hybridization with a maximum sensitivity level up to 0.066ng/m1/Hz.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.4
• /
• pp.1440-1446
• /
• 2012

This paper presents an experimental study of heat transfer and pressure drop characteristics of supercritical carbon dioxide with PAG inside a horizontal microfin tube. Heat transfer coefficient and pressure drop gradients were measured at 10 MPa in pressure and 520 kg/$m^2s$ in mass flux with variation of PAG mass concentration from 0.06% to 2.26%. The tendencies of both heat transfer and frictional pressure drop characteristics show the same as those of pure $CO_2$ up to 0.3% in PAG mass concentration. In case of 2.26% in PAG mass concentration, measured heat transfer coefficients showed 50% lower than those of pure $CO_2$ near the pseudocritical temperature and measured frictional pressure drop gradients show 1.6 times higher in comparison with those of pure $CO_2$ at $60^{\circ}C$ in $CO_2$ bulk temperature.