• 소음진동
• /
• 제6권4호
• /
• pp.513-519
• /
• 1996

This paper is concerned with the bubble sound at the accumulator which is generated by the difference of the high pressure side and the low pressure side in the cycle of the refrigerator. The causes of the bubble sound generation are verified by the visualized test of the operating refrigerant flow at the accumulator and the measurements of the temperature and pressure. Two cases were tested, one with the accumulator has a orifice and the other with the accumulator hasn't a orifice. So that, it is presented the comparison of the bubble sound levels and spectrums in each cases. To predict the bubble sizes when they are generated, the linearized equation driven by Strasberg is used.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계 학술대회논문집(수송기계편)
• /
• pp.180-185
• /
• 2005

Gear whine noise of the axle and transmission is getting more important for reduction of vehicle noise, because major noise of vehicle was reduced. Therefore, in this paper, axle noise and vibration is measured, then the modal analysis and running modal analysis is applied for identification of axle gear whine noise. And To reduce axle noise, Various structural modifications are performed by using FEM and BEM techniques.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계 학술대회논문집(수송기계편)
• /
• pp.29-32
• /
• 2005

This paper presents experimental analysis of a friction-driven wheel that is responsible for wheel squeal. Squeal noise generating mechanism and environment of train u heels has been tried to reproduce under laboratory condition. Scale down size rail and wheel are made and influential parameters to squeal noise are measured, e. g. frictional force, pressure between rail and wheel, creep speed of rail. Negative damping characteristic curve are calculated currently. Necessary relating computational analysis is also carried on.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.336.2-336
• /
• 2002

There are many researches to identify the rigid body properties from the mass-line obtained by impact hammer testing. The correct rigid body properties of the structure may be estimated if the mass-line of the structure could be obtained exactly. When the structure is mounted by elastic materials, the mass-line cannot be read correctly from the impulse response spectrum. The reason is due to the effects of rigid body modes of mounted structure. (omitted)

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.172-177
• /
• 2001

This paper proposes an adaptive feedforward controller (AFC) based on LMS for periodic disturbance rejection in active magnetic bearing system. The proposed controller does not alter the stability and robustness of the existing AMB system. It is shown that the control delay due to the eddy current as well as runout and unbalance can be identified and compensated using the estimated displacement from the measured magnetic flux. The simulation results confirm that the proposed scheme successfully identifies and compensates for the runout, unbalance and eddy current effect, leading to a high-precision magnetic bearing system.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.338.2-338
• /
• 2002

Passengers in automobile or train are exposed to a worse noise environment when they are in the tunnel than in the open field. This is due to a relatively higher space density of sound energy by multiple reflection phenomenon of noise generated by operation of transportaton vehicles from tunnel wall compared to open field. In this study, noise characteristics of subway train running through a tunnel were investigated at straight/cruved track and tunnel type(semi circula/box). (omitted)

• 한국소음진동공학회논문집
• /
• 제25권6호
• /
• pp.399-405
• /
• 2015

In this work we use the mode decomposition technique employing chirplet transform, which is able to separate the individual modes from dispersive and multimodal waveform measured with the magnetostrictive sensor. The mode decomposition technique is also used to estimate the time-frequency centers and individual energies of the reflection, which would be used to locate and characterize axial defects. The arrival times of the separated modes are calculated and the axial defect lengths can be evaluated by using the estimated arrival time. Results from an experiment on a carbon steel pipe are presented and it is shown that the accurate and quantitative defect characterization could become enabled using the proposed technique.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1995년도 추계학술대회논문집; 한국종합전시장, 24 Nov. 1995
• /
• pp.68-73
• /
• 1995

반사음이 포함된 신호의 계측을 통하여 원음의 크기와 반사계수의 크기, 지연시간 등의 추출을 수치적 예를 사용하여 규명해 보았다. 반사계수의 측정시, 폐쇄된 음장에서는 정상파비로 표시되는 단일 주파수 신호를 사용하는 것이 실제 계측시 가장 손쉬운 방법이며, 광역의 주파수 성분에 걸쳐 그 값을 파악할 필요가 있는 경우에는 켑스트럼 상에서 반사파의 효과가 원음과 확연히 구분되는 신호를 사용하는 것이 신호처리 과정에서 불필요한 부담을 제거시켜 준다. 개방 음장에서는 반사파가 1개 밖에 포함되지 않으므로 이 경우에는 PSD 상의데이터 처리를 통하든지 또는 캡스트럼의 재편집을 통하여 원음의 크기와 성분 그리고 반사계수 등을 손쉽게 추출해 낼 수 있다. 광대역 주파수 성분을 가진 음원을 계측에 사용할 경우에는 comb lifter의 적용에 보다 세심한 주의를 기울일 필요가 있으며 켑스트럼 상의 추가 충격응답함수의 식별에 보다 더 합리적인 방법이 강구되어야 할 것이다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1995년도 추계학술대회논문집; 한국종합전시장, 24 Nov. 1995
• /
• pp.136-141
• /
• 1995

Room Air Conditioner(이하 RAC) 실내기는 열교환기, Cross Flow Fan(이하 CFF), 곡률, Stabilizer(이하 STB) 등 여러 설계인자가 소음, 풍량 및 압력 등에 상호 복합적으로 연성(Coupled)되어 있어 각 인자가 성능에 미치는 영향을 정량적으로 밝혀 내기가 쉽지 않다. 따라서 RAC 실내기의 고성능 및 저소음화를 실현하기 위해서는 실내기를 구성하는 각 인자간의 상호 관련성 및 각 인자가 소음.성능 등에 미치는 영향을 체계적으로 분석하는 것이 필수적이다. 본 연구에서는 설계인자중 소음 및 풍량에 민감한 영향을 주는 STB 위치 및 형상 등에 관하여 자세히 다루고자 한다. STB위치의 적절한 범위를 설정하기 위해 Laser Doppler Velicitimeter(이하 LDV)를 이용하여 곡률별 실내기 내부의 유속분포 및 속도 벡터를 측정하였고, CFF내부 Vortex의 정확한 위치를 찾아냈다. 또한 실내기 저소음화를 위한 소음원 규명 측면에서 실내기 내부의 난류도와 관련하여 속도 Fluctuation을 정의하고, 실험을 통해 구하였다.

• 소음진동
• /
• 제9권3호
• /
• pp.570-576
• /
• 1999

This paper presents numerical and experimental results of modal parameter identification in a generator stator frame for 500 MW fossil power plants. A commercial finite element analysis S/W was employed for modal analysis. The generator is excited by alternating electromagnetic forces, mainly of 120 Hz in 60 Hz machines, due to magnetic field and electric current in windings. It is necessary to verify that the stator frame has adequate frequency margin from the excitation frequency to avoid possible resonance when operating. Thus, frequency margin required for the stator frame is established using the numerical and experimental results. The results show that the stator frame meets the frequency-margin requirements. Also, results of modal analysis for design modification in order to reduce weights of the stator frame without deteriorating vibration characteristics are presented.