• The Korean Journal of Petroleum Geology
• /
• v.1 no.1 s.1
• /
• pp.29-35
• /
• 1993

Seismic reflection data can be used to extract information about the velocity structure of the earth. This process is called a velocity inversion of the seismic data. However, it is difficult to recover a broad band reflection coefficient series because the frequency band of seismic trace is limited. The linear programming method has been examined to find the simplest velocity model that has frequency components consistent with the usable frequencies of the seismic trace and interval velocity data. The velocity structure of the earth is displayed in pseudovelocity section. After the linear program had been tested with a synthetic seismic trace, it was applied to the seismic reflection data of the Block Ⅱ in the Yellow Sea. By comparing the pseudovelocity section with sonic logs obtained from the well in the same area, it was possible to define the lithostratigraphy and the boundaries of Cretaceous volcanics and Cretaceous metavolcanics.

• Economic and Environmental Geology
• /
• v.17 no.1
• /
• pp.49-55
• /
• 1984

This paper describes three-dimensional (3-D) standard curves for conductive dipping buried bodies in induced polarization (IP) method. Dipole-dipole IP responses for the dipping bodies are calculated by the numerical modeling technique using an integral equation solution. Dip angles of the bodies are 0, 20, 45, 70 and 90 degrees, respectively. The horizontal (0-degree dip) and vertical (90-degree dip) bodies produce symmetrical patterns of IP responses. The dipping bodies of 20, 45 and 70 degrees, however, produce asymmertical patterns, with the highest IP contours dipping in the direction opposite to the bodies in pseudo-sections. The most remarkable asymmetrical pattern appears in the model of 20-degree dip. It is difficult to distinguish the body of 70-degree dip from that of 90-degree dip on the basis of dipole-dipole IP data. The IP pattern in pseudo-sections varies when the line moves away from the center of the body along strike, with the anomaly deeper and smaller in amplitude. IP maps seem to be more useful than IP pseudo-sections in predicting the location of target.

• The Journal of Engineering Geology
• /
• v.28 no.3
• /
• pp.397-409
• /
• 2018

Izumi sedimentary basin (ISB), west of Shikoku, Japan, is widely distributed across the western side of the Sakuragi Bend of the Japan Median Tectonic Line (MTL). It is not obvious how the ISB formed, but this feature is similar to an asymmetric pull-apart basin. The stratigraphic succession and tuff layers show that ages tend to decrease toward the Sakuragi Bend. We investigate whether the ISB is an asymmetric pull-apart basin using analogue model experiments with running sand. A pull-apart basin of length 60 cm and width 20 cm is formed, and secondary normal faults appear on the surrounding surface. A cross-section parallel to the direction of displacement shows that the stratigraphic succession of the pull-apart basin becomes younger toward the releasing bend. A listric normal fault, which has the opposite dip to the master fault, is observed in a cross-section perpendicular to the direction of displacement. These results are consistent with the observed properties of the ISB west of Shikoku, thereby supporting the possibility that the ISB is an asymmetric pull-apart basin.

• Economic and Environmental Geology
• /
• v.39 no.4 s.179
• /
• pp.473-483
• /
• 2006

Although application of electrical methods in Korea began with observation of self potentials before World War II, the methods were developed slowly by the beginning of 1980's when a major burst of development activity took place. DC resistivity methods are applied in Korea more to geotechnical problems rather than to environmental ones unlike other developed countries. As with every other branch of technology, the evolving speed of the silicon chip and of streaming data to hard disk has revolutionized data collection and noise reduction processing. The last two decades saw major advances in data collection, processing, and interpretation of electrical data. Development of smooth-model two-dimensional (2D) resistivity inversion is one of the most visible changes to geophysical interpretation of the last 40 years and is now routinely applied to apparent resistivity data. The ability to represent resistivities in section rather than pseudosection view has revolutionized interpretation. Although calculation of sensitivities for general electromagnetic problems require numerous forward modelings, DC resistivity methods can enjoy computational efficiencies if sources and receivers occupy the same position, and previously intractable 3D inversion is now becoming available.

• Economic and Environmental Geology
• /
• v.29 no.3
• /
• pp.345-355
• /
• 1996

The effectiveness of various electrode configurations in horizontal mappings and 1-D inversions of vertical sounding data for delineating 2-D structures was studied. Apparent resistivity values of three point, dipole-dipole, Wenner, and Schlumberger mappings were simulated for such structures as vertical dyke, tabular prism, buried vertical fault, ramp and complex structure by finite difference method (FDM) and they were compared with each other. Also 2-D cross sections for three structures obtained by interpolation of 1-D inverted sounding data in terms of three layers were compared for Schlumberger and Wenner arrays. On these cross sections, horizontal and vertical resistivity interfaces of the 2-D structures are revealed relatively clearly. Apparent resistivity curves of Schlumberger mapping show vertical resistivity discontinuities very well. On the whole, Schlumberger array is superior to the other arrays in electric sounding as well as mapping. This study clearly indicates that interpretations of 2-D structures based on 1-D inversion are possible.

• The Journal of Engineering Geology
• /
• v.25 no.4
• /
• pp.459-472
• /
• 2015

A recently developed tunnel section enlargement method can maintain traffic flow during construction by using a protector. By keeping traffic flowing, it can minimize the lost time and costs associated with diversions and also the accompanying environmental pollution. On the other hand, installing the protector can lengthen the construction period and increase the direct cost. This paper presents a method for analyzing the economic feasibility of tunnel section enlargement methods considering the direct construction cost and the indirect social cost. The indirect costs are divided into categories of: vehicle driving cost, travel time delay cost, and environmental pollution cost. The economic efficiency of existing technology is compared with the new method in an case study of Namsan Tunnel 3.

• The Journal of Engineering Geology
• /
• v.26 no.3
• /
• pp.339-352
• /
• 2016

The best way of investigating the physical and mechanical properties of subsurface materials is the combined interpretation of data from borehole geophysical surveys and geotechnical experiments with rock samples. In this study two surface seismic surveys with refraction and surface-wave method are alternatively conducted for downhole seismic surveys in test site for geological field trip in Jeungpyung, Chungbuk. P- and S-wave velocity structures are delineated by refraction and MASW (multichannel analysis of shear waves) methods, respectively. Possion's ratio section, reconstructed from P- and S-wave velocities, is correlated to the outcrop geological features consisting of reddish sedimentary rock, gray volcanic rock, and joints/fractures. In addition, rock samples representative for reddish sedimentary and gray volcanic features are geotechnically analyzed to provide physical, mechanical properties, and elastic modulus. Dynamic elastic moduli estimated from geophysical data is found to be higher than the one from geotechnical data. Reddish sedimentary rock characterized with low porosity and moisture content corresponds to the zone of low electrical resistivities and their small variations in the resistivity sections between the rainy and dry days. This trend suggests that the weathered gray volcanic rock and the nearby fractures with higher low porosity and moisture content are interpreted to be good carrier especially in rainy season.

• Economic and Environmental Geology
• /
• v.48 no.6
• /
• pp.509-523
• /
• 2015

This study introduces newly implemented geological well logs database for Jeju public water wells, built for a research project focusing on integrated hydrogeology database of Jeju Island. A detailed analysis of the existing 1,200 Jeju Island geological logs for the public wells developed since 1970 revealed six major indications to be improved for their use in Jeju geological logs DB construction: (1) lack of uniformity in rock name classification, (2) poor definitions of pyroclastic deposits and sand and gravel layers, (3) lack of well borehole aquifer information, (4) lack of information on well screen installation in many water wells, (5) differences by person in geological logging descriptions. A new Jeju geological logs DB enabling standardized input and output formats has been implemented to overcome the above indications by reestablishing the names of Jeju volcanic and sedimentary rocks and utilizing a commercial, database-based input structured, geological log program. The newly designed database structure in geological log program enables users to store a large number of geology, well drilling, and test data at the standardized DB input structure. Also, well borehole groundwater and aquifer test data can be easily added without modifying the existing database structure. Thus, the newly implemented geological logs DB could be a standardized DB for a large number of Jeju existing public wells and new wells to be developed in the future at Jeju Island. Also, the new geological logs DB will be a basis for ongoing project 'Developing GIS-based integrated interpretation system for Jeju Island hydrogeology'.

• Economic and Environmental Geology
• /
• v.2 no.2
• /
• pp.1-35
• /
• 1969

The structure and geologic history of the Triassic basin in southern Connecticut have been interpreted by using gravimetric data. A gravity survey of 800 gravity stations was made by the U.S. Geological Survey in the southern Connecticut area. The resulting data were reduced by the Bouguer method and then plotted and contoured along with the generalized geology. Residual gravity maps were prepared by different methods to obtain the most plausible agreement with the known geology of the area. Seven gravity profiles across the basin are presented to show the distribution of the Triassic deposits that could produce the measured anomalies. It is concluded that the basin was formed by successive step faulting in the late Triassic period and that the sediments accumulated progressively in this basin. The deepest portion of the basin is located in the middle of the present Triassic belt and reaches a depth of about 2 miles below the surface. The data also appear to indicate the possible source areas for the basalt which at present forms the lava flows, sills, and dikes exposed in the Cheshire and Gaillard regions. The information concerning the tectonic history of the Connecticut Triassic Valley aids considerably in establishing the geologic history of the Appalachians in late Triassic time.

• The Journal of Engineering Geology
• /
• v.21 no.1
• /
• pp.57-64
• /
• 2011

Three-dimensional slope stability analysis was applied to a failed dual-lithology slope containing both granite and an andesitic dyke, taking account of the differences in shear strength of the different lithologies. A direct shear test of the soil-rock boundary was performed to examine the shear strength of two different types of failure surfaces within different lithologies, and a laboratory test was performed on an upper, weathered soil layer. The test results indicate that shear strength was lower at the soil-rock boundary than within the weathered soil layer. A representative geological section was subjected to two-dimensional slope stability analysis using a limit equilibrium method to assess whether the distribution of lithologies upon the slope influences the results of stability analysis. The results were then compared with those of three-dimensional slope stability analysis, for which input parameters can be varied according to the distribution of lithologies upon the slope. The three-dimensional analysis yielded safety factors of 1.26 under dry conditions and 0.55 under wet conditions, whereas the two-dimensional analysis yielded unstable safety factors of 0.92 and 0.32, respectively. These findings show that the results of stability analysis are affected by the distribution of different lithologies upon the slope. Given that the studied slope collapsed immediately after rainfall, it is likely that the results of the three-dimensional analysis are more reliable.