• The Journal of Engineering Geology
• /
• v.8 no.2
• /
• pp.189-203
• /
• 1998

Packer-dilatometer techniques, which are borehole-dilatometer techniques using commercial rubber packer, were developed to measure the deformability of rocks. Packer-dilatometers for 0.5 inch, AX, BX, NX and HX size boreholes were developed and were used for rock deformability measurements in the field. In the packer-dilatometer method, the packer pressurizes the borehole-wall and the borehole deformation is determined by the amount of fluid injected into the packer. A detailed description of the theoretical development of quantitative interpretation of the packer-dilatometer method; apparatus, setup and procedures for the determining of calibration constants; contact pressure determination and field tests using the packer-dilatometer are provided.

• The Journal of Engineering Geology
• /
• v.12 no.1
• /
• pp.89-93
• /
• 2002

Seismic geotomography method was performed to verify rock-filled settlement and its stability in No.38+0 profile and No.40+0 profile. The velocity distributions of geotomography method expressed the quantitative value of the ground conditions. The rock-filled layer and in-situ sediments layer are clearly divided on the basis of seismic velocity 2100 m/sec which is derived from the results of seismic geotomography and boring. Current rock-filled settlement conditions are somewhat different from designed settlement estimation line. Seismic geotomography represents current settlement conditions as a quantitative analysis.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.5
• /
• pp.47-58
• /
• 2015

Triggering rainfall and geologic conditions with the state of slope hazard were investigated based on the field investigation and collected data on the slope hazard during the period between 2011 and 2014 in Korea. Analysis results showed that most of slope hazards occurred in metamorphic rock and debris flow was the most frequent type of slope hazard. Slope hazard increased when the higher monthly mean rainfall was recorded. However, most of slope hazard occurred when certain time elapsed after the moment of maximum hourly rainfall. Finally, more than one month of long-term rainfall was shown to be related to the frequency of slope hazard in the period.

• The Journal of Engineering Geology
• /
• v.17 no.4
• /
• pp.615-621
• /
• 2007

Seismic refraction survey which is assumed to be effective for investigating of the amount of bed sediment was applied to two sites having different soil types. The ten lines of seismic surveys were carried out in the areas of the levee near the Wolchon Bridge, Yongin and the Damam levee, Yecheon. At the same time, two borehole data were obtained to be used in classifying geological formations on the inverted seismic sections. As the results of interpolating the depths of geological formations and the surface elevation values, it is possible to estimate the volume of the bed sediments at $24,000m^3\;and\;56,000m^3$ in Yongin and Yecheon, respectively.

• The Journal of Engineering Geology
• /
• v.3 no.3
• /
• pp.267-278
• /
• 1993

Ground-water temperature is one of the parameters for observing diarges in the state of the ground-water regime in time and space, which relate to conditions for recharge as well as the influence of various natural and man-induced fadors on the regime. Because ground-water satura tes much of the rock materiats in the upper layer of the earth's csust the water temperature reflects in part the temperature of the water-bearing rocks. The mobffity and thennal capadty of groud-waters, however, serves to redistribute some of the heat within the stratosphere and to influence the developement of the geothermal regime within this sphere. The utilization of temperature data of the study area(25 points) in the solution of hydrogeologic problems requires an understanding of some of the fundamental aspects of subsurtice temperatures. These include the depth of penetration of heat waves generated of the surtace, the rate of propagation of the waves, and the geothermal gradient in the study area of Taegu.

• The Journal of Engineering Geology
• /
• v.4 no.3
• /
• pp.343-356
• /
• 1994

When most of the industry and social indirect facilities such as the large structure, power plant or road, rail-road are constructed, the new slope may lead to the slope failure. The failure models for slopes have been developed by using the results of in-situ and laboratory tests to investigate the mechanisms and types of the slope failure. The safety factor of a slope may be obtained based on the proposed model and the slope can be reinforced to meet the design criteria. The slope should be reinforced by using the optimum model that properly reflects the site condition, the method of reinforcement includes the increased safety factor either by decreasing a slope angle or by reinforcing the slope.

• The Journal of Engineering Geology
• /
• v.17 no.1 s.50
• /
• pp.115-123
• /
• 2007

Recently, accelerating population and advanced economy result in extending old freeways and constructing new freeways. To make a good freeway shape, tunnel constructions are also rapidly increasing. Therefore, a possibility of a collapse during a tunnel excavation is getting higher in a proportionate manner. Especially, tunnel excavation has increased in poor geological condition in order to maintain good alignment of road and the collapse of tunnel has often happened without reinforcement method. This research paper will analyze for ms and causes of the collapses for different geological conditions and applied reinforcement solutions by investigating typical collapse sites during highway tunnel constructions.

• The Journal of Engineering Geology
• /
• v.8 no.1
• /
• pp.1-12
• /
• 1998

The fracture size among geometric parameters of the fracture system is treated as one of the most important factors in the geotechnical and hydrogeological analysis. However, several uncertainties in data acquisition and analysis pmcess about the fracture size are not clear yet. This study presents the current status on the estimation of the fracture size and verifies the estimating method using forward modeling approach. The factors considered are the variation of fracture intersection probabilities with different assumptions on the orientation of sampling planes and fracture size by using a simulated tleee dimensional fracture network model. If it is possible to analyze precisely the fracture intersection probabilities and the characteristics of probabilistic distnbution fiom cavern walls, outcrops or boreholes,the actual fracture size developed in rock rnass can be estimated confidently.

• The Journal of Engineering Geology
• /
• v.11 no.2
• /
• pp.163-174
• /
• 2001

For quantitative evaluation of geotechnical engineering properties such as rippability and diggability, clear interpretation on the subsUJiace velocity structures should be preceded by figuring out top soil, weathered and soft rock layers, shape of basement, fracture zones, geologic boundary and etC. from the seismic refraction data. It is very important to set up suitable field parameters, which are the configuration of profile and its length, spacings of geophones and sources and topographic conditions, for increasing field data Quality. Geophone spacing of 3 to 5m is reconunended in the land slope area of house land development site. In refraction tomography technique, the number of source points should be more than a Cluarter of available channel number of instrument and the subsurface structure interpretation can be decreased the artifact of inversion by topographic effect. Compared with core logging data, it is shown that the velocity range of the soil is less than 700m/s, weathered rock 700~1,200m/s, soft rock 1,200~1,800m/s on the velocity tomogram section. And the upper limit of P-wave velocity for rippability is estimated 1,200 to 1,800m/s in land slope area of gneiss.

• The Journal of Engineering Geology
• /
• v.12 no.1
• /
• pp.35-51
• /
• 2002

This study aims to establish the methodology for design of an optimum water curtain system of the unlined underground oil storage cavern satisfying the requirements of hydrodynamic performance in a volcanic terrain of the south coastal area. For the optimum water curtain system in the storage facility, the general characteristics of groundwater flow system in the site are quantitatively described, i.e. distribution of hydraulic gradients, groundwater inflow rate into the storage caverns, and hydrogeologic influence area of the cavern. In this study, numerical models such as MODFLOW, FracMan/MAFIC and CONNECTFLOW are used for calculating the hydrogeological stability parameters. The design of a horizontal water curtain system requires considering the distance between water curtain and storage cavern, spacing of the water curtain boreholes, and injection pressure. From the numerical simulations at different scales, the optimum water curtain systems satisfying the containment criteria are obtained. The inflow rates into storage caverns estimated by a continuum model ranged from about 120 m$^3$/day during the operation stage to 130~140m$^3$/day during the construction stage, whereas the inflow rates by a fracture network model are 80~175m$^3$/day. The excavation works in the site will generate the excessive decline of groundwater level in a main fracture zone adjacent to the cavern. Therefore, the vertical water curtain system is necessary for sustaining the safe groundwater level in the fracture zone.