• Korean Journal of Optics and Photonics
• /
• v.29 no.6
• /
• pp.247-252
• /
• 2018

We report amplification of a small signal in a diode-pumped Cs vapor cell with 500 torr of ethane buffer gas, in the low-pump-power regime of 200 mW or less. For efficient amplifier operation, the pump and signal beams were coupled to a single-mode optical fiber, and completely overlapped in the Cs vapor cell. We investigated the amplification of the small signal according to cell temperature, signal power, and pump power. An amplification factor of 56 was achieved under the conditions of cell temperature of $115^{\circ}C$, signal power of 0.1 mW, and pump power of 200 mW.

• Proceedings of the Optical Society of Korea Conference
• /
• 2009.10a
• /
• pp.66-67
• /
• 2009

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.12
• /
• pp.37-43
• /
• 2009

This paper describes a monolithic Darlington-cascade amplifier (DCA) operating at X-band, realized with a 0.35-micron SiGe bipolar process, which provides 45 GHz $f_T$. A conventional cascade amplifier was also designed on the same process and tested to establish a reference. Compared to the reference cascade amplifier, the proposed monolithic amplifier circuit exhibits an improved gain of 2.5 dB and improved output power 1-dB compression point of 5.2 dB with 72% wider bandwidth. Measurement results show 19.5 dB gain, 11.2 dBm 1-dB compression power, and 3.1 GHz bandwidth. These results demonstrate that the Darlington-cascade cell is an advantageous substitute to the conventional cascade amplifier.

• 전기의세계
• /
• v.24 no.6
• /
• pp.45-49
• /
• 1975

후막 HIC는 computer 회로뿐만 아니라, 자동차의 전압 조정기 고출력, 증폭단, 텔레비젼 CRT관의 전력 구동단등의 고출력 회로와, 텔레비젼 또는 산엽용 전자 장치의 VHF, UHF, 회로 구성에 많이 이용된다. 국내에서는 전자시계 제작에 수개 업체에서 HIC 기술을 이용하고 있다. 더 높은 주파수대인 마이크로-웨이브대 (파장이 cm대에서 mm대에 이른다)장치의 소형화는 박막 HIC에 의하여 실현되고 있다.

• 대한방사선방어학회:학술대회논문집
• /
• 2011.11a
• /
• pp.262-263
• /
• 2011

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.1301-1304
• /
• 2005

In this paper, we used class D amplification circuit proposed to improve the decline of error rate caused by rapidly variable impedance in the Power Line Communication. We manufactured voltage drive circuit and current drive circuit that are driven circuit of power line modem on the present. And with the same power line modem, we made a comparison experiment applying the driver circuit that used class D amplifier proposed in this paper. As a result of Experiment, We showed that it has more superior than other existing drive circuits at the impedance change in the power line communication.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.3
• /
• pp.569-577
• /
• 1999

A wideband RF receiver for satellite mobile communications system was fabricated and evaluated of performance in low noise amplifier and high gain amplifier. The low noise amplifier used to the resistive decoupling and self-bias circuits. The low noise amplifier is fabricated with both the RF circuits and the self-bias circuits. Using a INA-03184, the high gain amplifier consists of matched amplifier type. The active bias circuitry can be used to provide temperature stability without requiring the large voltage drop or relatively high-dissipated power needed with a bias stabilized resistor. The bandpass filter was used to reduce a spurious level. As a result, the characteristics of the receiver implemented here show more than 55 dB in gain, 50.83 dBc in a spurious level and less than 1.8 : 1 in input and output voltage standing wave ratio(VSWR), especially the carrier to noise ratio is a 43.15 dB/Hz at a 1 KHz from 1537.5 MHz.

• Geophysics and Geophysical Exploration
• /
• v.14 no.1
• /
• pp.69-79
• /
• 2011

In this study, empirical site amplifications and S-wave velocity profiles for shallow and deep soils are estimated using earthquake ground motion records in metropolitan Manila, the Philippines. We first apply a spectral inversion technique to the earthquake records to estimate effects of source, path, and local site amplification. The earthquake data used were obtained during 36 moderate earthquakes at 10 strong-motion stations of an earthquake observation network in Manila. The estimated Q value of the propagation path is modelled as $54.6f^{1.1}$. Most of the source spectra can be approximated with the omega-square model. The site amplifications show characteristic features according to surface geological conditions. The amplifications at the sites in the coastal lowland and Marikina Valley shows predominant peaks at frequencies from 1 to 5 Hz, while those in the central plateau are characterised by no dominant peaks. These site amplifications are inverted to subsurface S-wave velocity. We, next, discuss the relationship between the amplifications and average S-wave velocity in the top 30m of the S-wave velocity profiles. The amplifications at low frequencies are well correlated with the averaged S-wave velocity. However, high-frequency amplifications cannot be sufficiently explained by the averaged S-wave velocity in the top 30 m. They are correlated more with the average of S-wave velocity over depths less than 30 m.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.9
• /
• pp.714-723
• /
• 2003

An effective technique to increase the signal swing and reduce noise is to use fully-differential -circuits. However, design of a common-mode feedback (CMFB) circuit that stabilizes the common-mode output level is essential. In this paper, a general description is given to fully-differential amplifiers with their CMFB loops, then a new error amplifier that is just composed of transistors and stabilizes the DC output level is proposed. We designed a simple and efficient bias circuit that allows the stability and maximum input swing. Simulation result shows the enhanced phase margin and increased differential-mode input swing with a proposed error amplifier.

• Proceedings of the IEEK Conference
• /
• 2003.07c
• /
• pp.2485-2488
• /
• 2003

본 논문에서는 DSP를 이용하여 운동하는 물체의 회전량을 측정하는 실린더형 진동 자이로스코프(이하 자이로) 제어기를 개발하였다. 진동 자이로를 구동하기 위해서는 정밀 진동제어와 신호 처리와 같은 고급 제어 기술이 필요하다. 정밀진동제어는 진동 자이로를 구동하기 위해 필요한 핵심기술로써 기존의 PLL(phase-locked loop)방식은 외부환경에 민감하여 구현이 까다로울 뿐만 아니라 자이로 개개의 고유 진동수가 다르기 때문에 대량 생산에 어려움이 있었다. 또한 자이로 출력 신호로부터 회전량을 검출하기 위해서는 진폭과 당향성 검출의 본 회로뿐만 아니라 잡음 제거와 신호 증폭, 온도 보상과 같은 전처리 과정도 필요하다. 본 논문에서는 DSP를 통해 정밀 진동제어와 잡음 제거, 방향성 검출 등의 기능들을 구현하였으며 증폭과 진폭(회전량) 검출은 아날로그 회로를 이용하였다. 또 한 외부와의 인터페이스를 위해 D/A 회로를 설계하였고 이들을 실험을 통해 검증하였다.