• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.2
• /
• pp.237-246
• /
• 1999

A miniaturized waveguide bandpass filter is designed by combining a corrugated lowpass structure and a highpass configuration based on the cut-off effect of waveguides. It is smaller than the conventional waveguide bandpass filter composed of half-wavelength resonators and has wider spurious free characteristics. Optimized design data for a seven-order waveguide bandpass filter with the symmetrical structure are given at the center frequency of 10 GHz with 800 MHz bandwidth. Measured bandwidth of the center frequency of 9.97 GHz is 840 MHz and measured insertion loss is 0.97dB, The length of the bandpass filter is 64.38mm. The first spurious response is produced at 26.1 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.7
• /
• pp.709-715
• /
• 2002

In this paper, a novel low profile dual feeding microstrip antennas with microstrip and H-shaped aperture feeding are proposed to achieve high isolation and easy feeding, and the validity of the proposed antennas is demonstrated experimentally. In the proposed single and 1$\times$4 array antenna, the measured isolations are less than -49 dB and -48 dB, impedance bandwidths are 4 % at 12.5 GHz and 2.1 % at 14.25 GHz for the VSWR<1.5 in both antennas and maximum gains are 8.25 dBi and 14.2 dBi.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.11
• /
• pp.47-53
• /
• 2014

We propose a parameter estimation algorithm for radar signal active cancellation based on the Pade approximation that requires much less samples than the conventional MLE scheme. We also verify that the radar signal with time-variant center frequency can be estimated with proposed algorithm by renovating the center frequency. We present simulation results for radar signal active cancellation to show the accuracy of estimated signal using proposed algorithm by calculating the ratio of RMSE of estimated signal to amplitude of hostile radar signal.

• Current Industrial and Technological Trends in Aerospace
• /
• v.9 no.1
• /
• pp.77-89
• /
• 2011

The vibration and noise reduction issue is very important in helicopter since the thrust and flight control force of helicopter are generated by rotating drive system. In past, there was a passive method to reduce vibration and noise to focus on specified frequency. Now, there are various active method to reduce vibration and noise due to technology development. This paper describes the worldwide technology trend of vibration and noise active control in helicopter. At introduction, generalmethod of vibration and noise reduction.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.1
• /
• pp.125-135
• /
• 2001

A 8$\times$4 microstrip antenna array is designed at 5.3 GHz and its characteristics are investigated with respect to the application in dual polarized synthetic aperture radars. The design is focused on the achievement of a wide bandwidth, a high polarization purity, a low loss, a good isolation and some mechanical requirements suitable for the application. The antenna is fed by a -3 dB tapered feed network, and is composed of dual polarized SSFIP (Strip-Slot-Foam-Inverted Patch) elements with honeycomb and shielding plane. Simulation results for the antenna array are presented and compared with measurements. It is observed that the antenna shows a bandwidth of 80 MHz, a polarization isolation better than 20 dB, an isolation of 40 dB, and good mechanical characteristics.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.5
• /
• pp.965-970
• /
• 2018

In this paper, the transition of the folded substrate integrated waveguide (FSIW) using two substrates is suggested and applied to the bandpass filter. The FSIW has similar characteristics with the SIW and can be reduced the width of the SIW. The transition between the FSIW to the microstrip is designed by using shorted quarter wavelength line. Also, the bandpass filter is designed by using the FSIW and the elliptic lowpass filter of 5 section. Fabricated bandpass filter has the center frequency of 5.75 GHz and the bandwidth of 33.2%. Also, the insertion loss and return loss at the center frequency are 0.63dB and 19.1dB, respectively.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.4
• /
• pp.787-792
• /
• 2004

This paper shows the design, fabrication and performance of oscillator appled to 5.5GHz RF module for local wireless communication system. Super low noise HJ FET of NE3210S01 is used to obtain a good phase noise Performance. The design Parameters for the optimum operating performance are simulated with ADS simulation. The measured out Power is 10 dBm at 5.5GHz, the second harmonic suppression -31 dBc, and the phase noise characteristics -98.83 dBc at 100kHz offset frequency, respectively. This implemented oscillator is available to local wireless Communication system.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2004.05b
• /
• pp.96-100
• /
• 2004

This paper shows the design, fabrication and performance of oscillator appled to 5.5GHz RF module for local wireless communication system. Super low noise HJ FET of NE3210S01 is used to obtain a good phase noise Performance. The design Parameters for the optimum operating performance are simulated with ADS simulation. The measured out Power is 10 ㏈m at 5.5GHz, the second harmonic suppression -31 ㏈c, and the phase noise characteristics -98.83 ㏈c at 100KHz offset frequency, respectively. This implemented oscillator is available to local wireless Communication system.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.3
• /
• pp.541-546
• /
• 2010

The push-push DRO(dielectric resonator oscillator) using a multi-layer structure of LTCC(low temperature co-fired ceramic) fabrication is designed. After the single DRO of series feedback type in the center frequency of 8GHz is designed, the push-push DRO in the center frequency of 16GHz including the Wilkinson power combiner is designed. The bias circuit affecting the size of oscillator are embedded in the intermediate layer of the LTCC multi-layer substrate. As a result, the large reduction in the size of VCO is obtained compared to the general oscillator on the single layer substrate. Experimental results show that the fundamental and third harmonics suppression are above 15dBc and 25dBc, respectively, and phase noise characteristics of the push-push DRO presents performance of -102dBc/Hz@100KHz and -128dBc/Hz@1MHz offset frequencies from carrier.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.04a
• /
• pp.423-423
• /
• 2009

미진동 제어라는 분야에 대한 연구는 반도체 산업이 초고도화 및 초정밀화가 진전되고 있는 최근에 들어와 학계보다는 전문 반도체와 TFT-LCD의 미진동제어 관련 엔지니어 그룹과 정밀 장비 제작사를 중심으로 이루어져왔다. 고집적 생산 제품을 가공 및 검사하기 위해서는 가공 선폭 이상의 분해 성능을 가진 고정밀도의 생산 및 검사 장비가 필요하다. 이런 고정밀도 생산 및 검사장비는 내외부로부터 입력되는 진동에 민감한 영향을 받는다. 초기 반도체 산업을 주도한 미국을 중심으로 일부 학자와 반도체 진동 제어를 수행하는 전문연구소에서 작성한 BBN-Criteria는 정밀장비의 용도나 분해능 별로 정리된 진동허용규제치를 지침서로 사용하여 왔다. 그러나 장비의 엄밀한 주파수 특성 및 정밀도 측면에서 불확실한 영역부분을 가지고 있기 때문에 미소한 진동을 제어하는 구조 설계자 관점에서는 불충분한 자료이다. 그리고 주파수 분해능을 가진 진동허용규제치를 제시하는 것이 바람직하지만 대부분의 제작사에서는 그렇지 못하고 있다. 그런 이유에는 장비 개개의 진동허용규제치가 다른 고가의 장비 전량에 대하여 시험을 수행해야 하는 점, 가진(加振)특성, 중량, 크기 등의 진동실험 자체에 어려움 때문이다. 또한 진동실험시 가진주파수의 분해능의 결려에 따른 장비의 동적 특성이 고려되지 않은 불확실한 영역 부분을 포함한 진동허용규제치를 제시함으로서 불확실한 영역부분의 진동 하한치를 진동허용규제치의 상한치로 결정하는 문제로 인하여 진동허용규제치가 더욱 가혹하게 제시되어 건물 구조 설계와 방진의 어려움을 가중시킬 여지가 있다. 본 논문에서는 이런 어려움 등을 회피하는 방법으로 주파수응답함수(Frequency Response Function, FRF)를 이용하여 정밀장비의 진동허용규제치를 결정하는 간편하면서도 더욱 정밀한 새로운 방법을 모색하였다.