• Membrane Journal
• /
• v.25 no.2
• /
• pp.99-106
• /
• 2015

Polysulfone (PSF) hollow fiber membrane was prepared to separate $CO_2$ from the flaring gas. Fabricated PSF membrane system was fulfilled under 1 stage, 2 stage membrane process and simulation in order to confirm the operating condition for 99% of $CH_4$ and 1% of $CO_2$ concentration. Also, $25Nm^3/h$ bench scale $CO_2$ separation membrane system was operated under 1% of $CO_2$ concentration during 100 hr, and $CH_4$ recovery ratio was 98%.

• Polymer(Korea)
• /
• v.35 no.5
• /
• pp.390-394
• /
• 2011

Effects of silver nanoparticles on the polymerization rate and morphology of poly(vinyl acetate) (PVAc)/silver microspheres prepared by suspension polymerization of VAc were investigated. Scanning electron microscopy, transmission electron microscopy, X-ray diffraction and atomic absorption spectrometry were used to characterize the morphology and properties of the PVAc/silver microspheres. Due to the change of hydrophilicity of silver nanoparticles, appearance of the microspheres having golf ball-like convave surfaces was observed. Under controlled concentration of surfactant, PVAc/silver microspheres with various hollow structures were synthesized. In the case of silver nanoparticles modified by surfactant, the polymerization rate increased slightly. PVAc/silver microspheres with a conversion up to 80% were prepared via suspension polymerization.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1552-1557
• /
• 2004

This paper introduced about characteristics on the non-steady heat transfer of STS 304 hollow cylinder, In the non-steady state, the specific heat and conductivity are depended on the temperature variations, and these properties affect to the governing equation on heat conduction. But the most of numerical analysis on heat conduction is assumed to constant properties which is conductivity and specific heat. Assuming that conduction is assumed to constant properties which is conductivity and specific heat. Assuming that the properties are reacted sensitively, the numerical results can have the difference of between constant properties with non-constant properties. The main parameters are specific heat and conductivity. The temperature distributions of the STS 304 hollow cylinder became in steady state after 4 minutes in case of the constant properties. As the conductivity in varied with temperature, the temperature distributions became in steady state after 15 minutes. Therefore, a numerical analysis of the non steady state heat transfer will has to apply that conductivity varied with temperature.

• Membrane Journal
• /
• v.11 no.1
• /
• pp.14-21
• /
• 2001

Rapid backpulsing to reduce membrane fouling of hollow fiber ultrafiltration module (polyacrylonitrile with 50000 l'vlWCO, 1.4 rom OD and 0,9 mm ID) was studied with latex solutions. Values estimated by a theoretical model were compared with the ones obtained from the systems with or without backpulsing, Specific Cake resistance, time consUmt for cake growth, diffusion coefficient, and the rate constants of fnur fouling models; the complete, intermediate. standard blocking and cake filtration were calculated to obtain the theoretical values. High frequency backpulsing gave net increase of fluxes by 40~120%. Fluxes predicted by the model were in good agreement with experimental ones within 14% error bound, The optimum backpulsing strength was acquired at 20% in the ranges of 20~40% strength and the optimum frequcncv was acquired at 2 Hz in the ranges of 0.67~3 Hz.

• Membrane Journal
• /
• v.13 no.1
• /
• pp.20-28
• /
• 2003

In this study, we try to formularize simultaneous equations to make a prediction about pressure drop for designing intravascular artificial lung assist device. Designing parameters to predict the effect of pressure drop and designed modules under various conditions were studied through an experimental modeling before inserting the artificial lung assist device into as venous. We measured pressure drop in various number of hollow fiber membranes, when the inside diameter of shell is fixed in 3 cm, and tried to develope the prediction equations by curve fitting based on the correlation between the experimental pressure drop and the device frontal area or packing density. The results showed that pressure drop increased with 2nd order functional formula as the liquid flow rate, the frontal area, and the packing density increased. Also, we can estimate the pressure drop as a function of the frontal area or packing density. The pressure drop obtained from the experiment was similar to that from the equation, confirming the usefulness of the equation.

• Membrane Journal
• /
• v.28 no.5
• /
• pp.361-367
• /
• 2018

In this study, the nanofiltration (NF) composite membranes for the low pressure use were prepared using polyvinylidene fluoride (PVDF) hollow fiber membrane as a supporter. Poly styrene sulfonic acid (PSSA) and polyethyleneimine (PEI) were coated onto the PVDF membrane by both layer-by-layer and salting-out methods. To characterize the prepared NF membranes in terms of the flux and salt rejection, 100 mg/L feed solutions of NaCl, $MgCl_2$, and $CaSO_4$ were used at the flow rate of 1 L/min and the operating pressure of 2 bar at room temperature. The NF membranes coated with 20,000 ppm PSSA (ionic strength 1.0) solution for 3 minutes and then 30,000 ppm (ionic strength 0.1) solution for 1 minute were observed the best performance. The permeability and salt rejection were 38.5 LMH, 57.1% for NaCl, 37.9 LMH and 90.2% for $MgCl_2$ and 32.4 LMH and 54.6% for $CaSO_4$, respectively.

• Membrane Journal
• /
• v.26 no.5
• /
• pp.365-371
• /
• 2016

A numerical analysis was performed for a separation of carbon dioxide and methane using 2-staged, membrane process where two polysulfone hollow fiber membrane modules were connected to provide both the methane concentration richer than 95% and the recovery higher than 90% using the recycled flows. The Compaq Visual Fortran 6.6 software was utilized for the numerical simulation. Both the methane concentration and the recovery % of methane could be successfully predicted as the function of the operating conditions. As the feed pressure, the methane concentration, and the flow rate increase, the methane concentration in a product is also found to increase and the recovery of methane is found to decrease.

• Membrane Journal
• /
• v.29 no.3
• /
• pp.140-146
• /
• 2019

In this study, a selective layer of poly styrene sulfonic acid (PSSA) and polyethyleneimine (PEI) was formed by layer-by-layer method onto a porous polyacrylonitrile (PAN) hollow fiber membrane as the suppoter membrane. The salting out method was used by adding Mg salt to the coating solution. Several experimental conditions of the ionic strength, polymer concentration, and coating time were investigated, and the flux and rejection were measured at the operating pressure of 2 atm for 100 mg/L of NaCl, $MgCl_2$, and $CaSO_4$ as the feed solution. The membranes coated with PSSA 20,000 ppm, coating time 3 minutes, ionic strength 1.0, PEI 30,000 ppm, coating time 1 minute, and ionic strength 0.1 were observed the best. In the 100 ppm NaCl, $MgCl_2$, and $CaSO_4$ feed solutions, the flux of 20.4, 19.4, and 18.7 LMH, and the rejection of 67, 90, and 66.6%, respectively.

• Membrane Journal
• /
• v.23 no.1
• /
• pp.1-11
• /
• 2013

Poly(ether imide) (PEI)-poly(dimethylsioxane) (PDMS) composite membranes and their modules were prepared, which are capable of selective $CO_2$ separation from the mixture gas. The gas flow rate, concentration, recovery ratio of $H_2$ and removal ratio of $CO_2$ outflowing by stage-cut were characterized at $25^{\circ}C$ and the constant pressure. In addition, to increase the recovery ratio of $H_2$, one stage, two stage series connection, and three stages series + parallel connection tests were carried out. When the stage-cut was 0.32 for the three stages connection operation, the concentration $H_2$ of the produced gas and the recovery ratio of $H_2$ was 97% and 85%, respectively. And also the removal ratio of $CO_2$ was 90% was obtained and the recycled gas concentration was similar with that of the feed gases.

• The Journal of the Acoustical Society of Korea
• /
• v.17 no.4
• /
• pp.23-29
• /
• 1998

본 논문은 foraming층이 음파의 전달 특성에 미치는 영향 및 멘드릴형 광섬유 하이 드로폰의 광음향 감도 특성에 미치는 영향을 분석한 것이다. 유한 요소법을 이용하여 foaming층의 내부 구조에 따른 음파의 전달 특성을 분석하였고, AL(Aluminium)/foaming 및 Nylon/foaming 멘드릴(mandrel) 각각에 대하여 foaming층의 재질 및 두께 변화에 따른 광음향감도 변화를 분석하였다. 그 결과, foaming층 내의 구조변화의 영향을 무시할 수 있 었다. 또한 AL al cNylon층상 복합체인 멘드릴에서 foaming층의 탄성율이 낮을수록, 두께 가 증가할수록 공음향 감도는 증가하였다. 그러므로 1GPa 이하의 탄성율을 지닌 두꺼운 Foaming층을 사용하여 층상 복합체 멘드릴을 구성하는 것이 광음향 감도의 향상을 위하여 효율적이다.