• The Journal of Korean society of community based occupational therapy
• /
• v.8 no.2
• /
• pp.29-37
• /
• 2018

Objective : Sleep disorder caused by stress or disease to elderly currently. We tried to make clear constant exercise according to exercise intensity would have effect on sleep disorder in elderly using EEG and melatonin. Methods : Thirty subjects were over 65 years old who lived a senior facility in some parts. They were able to communicate and understand the purpose of the study. They also expressed their intension to participate actively in experiment. They should have alert consciousness and orientation about time, place, and people. Sleep disorder was assessed via below 6 hr total sleep time and Pittsburge Sleep Quality Index, which was satisfied with both of criterion at the same time. Exercises composed of low intensity walking, moderate aerobic exercise, and high intensity resistance strength. We used QEEG 8-System (LAXTHA Inc. KOREA) to check wave type and Polysomnograpy (Compumedics, Australia) to test quality of sleep. and Histologic features were observed by TTC (triphenyltetrazolium chloride) staining and H & E (Hematoxylin & Eosin) staining. Results : There was a significant sleep index and change of melatonin after aerobic exercise. There was a significant SOL, S1, S2, and SWS in aerobic exercise, but there was a significant SWS in walking and resistance strength. There was a significant change of delta wave especially in frontal and temporal region between exercises. Conclusion : They had different effects according to type of exercise, when elderly who have chemical, behavioral change of circadian rhythms did exercise consistently. Aerobic exercise had more effect on sleep disorder than other exercise. Therefore, we may supply proper exercise to elderly and high quality of life.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.965-968
• /
• 2008

The KS F 2403 method used on domestic sites for checking the compressive strength of a structure, sets the compressive strength of the concrete used in structural specimens as the compressive strength of testing specimens. Under this regulation, the curing method used for testing the specimens must be the standard ponding curing method (20$\pm$2$^{\circ}$C). However, because in-placed concrete is exposed to open air and cured under the seasonal temperature changes, the compressive strength of a real structure is different from the tested compressive strength. (Therefore,) This thesis first identifies the distinct characteristics of the strength development by applying the curing method listed under the KS and used for testing specimens on compressive strength tests; the atmospheric curing method, the sealed curing method, and the structural specimen core strength testing methods used for the in-sites quality checks including reckoning of the compressive strength of the structural specimens and form-demolding period; and the curing method suggested in this research, which sets the internal conditions of the structural specimens as the conditions of the applied curing method. Then, the thesis suggests the specimen curing method that most closely reenacts the compressive strength of the concrete used on the structural specimens

• Magazine of the Korea Concrete Institute
• /
• v.8 no.5
• /
• pp.156-162
• /
• 1996

The purpose of this study is to find experimentally bond properties of deformed bars in high strength concwtc. Bond properties of deformed bars in high strength concrete are tested i n tensile stress state. Eighty beam-end specimens are used for this experiment. Concrete compressive strength is used as main experimental variable, in addition a few variables affecting bond properties are used : bond length, cover thickness and bar diameter. The principal results obtained from this study are as follows ; - Bond strength is not proportionate to bond length in high strength concrete. The rate of bond strength increase followed by bond length rapidly diminish according to concrete strength increase. The reason is analyzed in FEM analysis that bond stress is not uniformly distributed in high strength concrete and concentrate on loading area. - Bond strength is linearly proportionate to cover thickness without regard to concrete strength. Especially the rate of strength increase is gradually increased by concrete strength.

• Journal of the Korean Society for Railway
• /
• v.12 no.1
• /
• pp.104-109
• /
• 2009

In order to apply FBG(Fiber Bragg Grating) sensor as one of reliable sensors in the commercial railway structure, the reliability of FBG sensor in the mechanical strength viewpoint have to be confirmed and the maximum strain should surpass the fracture strain of the host structure to measure the measurands until the host structures fail. In this paper, several factors that influence the mechanical failure strength of fiber Bragg grating sensors were analyzed. A set-up for dynamic tensile testing of optical glass fibers with fiber Bragg gratings was made. To increase the FBG failure strength, techniques relying on the H2 loading treatment and stripping methods were established and testified as a result of the tensile strength test of optical fibers.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05c
• /
• pp.176-181
• /
• 1996

중수로 원자로에서 핵심 구조물인 압력관은 합금이 사용되고 있는데, 고온, 고압의 방사선 분위기에서 사용되기 때문에 가동중 변형을 받는다. 따라서 본 연구에서는 압력관의 건전성 평가기술을 확보하기 위하여 Zr-2.5wt.% Nb 압력관의 집합조직과 온도 변화에 따른 강도 특성을 조사하였다. 집합조직의 변화는 시편의 채취방향을 달리하여 네 가지의 집합조직 변화를 주었으며, 이들 시편에 대해 상온에서 부터 45$0^{\circ}C$까지 온도를 변화시가면서 인장시험을 실시하였다. 온도가 증가함에 따라 시편의 집합조직과 관계없이 네 종류의 시편 모두가 30$0^{\circ}C$까지는 강도가 직선적으로 감소하는 현상을 보이며, 30$0^{\circ}C$에서 37$0^{\circ}C$ 사이의 온도에서 강도가 약간 증가하는 현상을 보였다. 또한 37$0^{\circ}C$이상의 온도에서는 강도가 다시 직선적으로 감소하는 경향을 나타냈다. 이 같은 현상은 30$0^{\circ}C$ 까지는 프리즘 슬림(-slip)으로 전위가 움직이다가 30$0^{\circ}C$ 이상의 온도에서부터 37$0^{\circ}C$까지는 피라미드 슬림(-slip)계의 경쟁 상호작용에 의한 추가적인 응력이 필요하여 나타난 현상이라 사료된다. 온도의 변화에 따른 강도와 연신율의 curve에서 30$0^{\circ}C$와 37$0^{\circ}C$의 범위에서 plateaus region과 연신율이 최소값을 갖는 것은 동적변형시효(dynamic strain ageing)현상과 관련이 있는 것으로 생각되나 추가적인 연구가 필요하다. 집합도가 변함에 따라 인장강도는 T(transverse)>L(longitudinal)> 30。> 45 。순으로 나타났으며 이는 slip과 twin의 복합적인 작용에 의한 것으로 해석된다.

• Journal of the Society of Naval Architects of Korea
• /
• v.30 no.4
• /
• pp.127-135
• /
• 1993

The ultimate strength formulas of ship panels are suggested in a simple and suitable form. Firstly, these formulas are derived from a full description of the variables that govern plate strength by using statistical data of actual ships. Secondly, under the assumption of plate mid-edge collapse using the Von-Mises' yield criterion and the new buckling formula, a general equation for the ultimate strength estimation is also derived. The existing test data are compared with these new formulas and a good correlation is shown.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.8 no.6 s.40
• /
• pp.67-72
• /
• 2004

In this study the overstrength factors of medium to low-rise bucking restrained braced frames (BRBF) were evaluated. Various design variables, such as number of stories, span length, yield strength of the brace, level of earthquake load, and the response modification factors. The overstrength factors were obtained using the nonlinear static analysis following the procedure proposed by ATC-19. According to the analysis results, the overstrength factors obtained from this study were generally larger than those proposed in 'AISC/SEAOC Recommended Provisions for BRBF'.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.368-368
• /
• 2021

기후 변화로 인한 극한사상의 크기와 빈도 변화를 예측하는 것은 수공 인프라 설계에 있어 주된 관심사 중 하나이다. 보통 극한사상에 대한 강도, 빈도, 지속시간에 대한 정보가 필요하며, 이는 일반적으로 IDF(Intensity-Duration-Frequency) 곡선으로부터 추출된다. 최근 CMIP(Coupled Model Intercomparison Project) 6단계에서 새로운 이산화탄소 배출 시나리오와 업데이트된 기후모델을 이용하여 미래의 기후에 대한 예측 시계열을 발표했으므로, 미래 기후 변화 시나리오를 기반으로 IDF 곡선을 새로 추정하고 미래 기간의 변화를 평가할 필요가 있다. 본 연구에서는 한국의 40개 지역에 대해 일단위 자료를 시단위로 축소(downscaling)한 후, 확률론적 일기생성기(stochastic weather generator)를 이용하여 30년 시단위 시계열을 100개의 앙상블로 생성하였다. 생성된 시계열로부터 연최대강수량 시계열을 재구성하여 GEV 분포와 gumbel 분포에 적용하였다. 적합도 검정(Anderson-Darling(AD) 검정 및 Kolmogorov-Smirnov(KS) 검정)을 수행하였으며, 과거 자료를 기반으로 생성된 IDF 곡선과 비교 검증하였다. CMIP5의 기후변화 자료를 사용한 결과와 CMIP6 기후변화의 결과를 비교하였으며, 본 연구의 주요 결과는 다음과 같다. (1) 향후 강우 강도는 증가할 것이며 강우 강도의 증가는 말기에 현저하게 관찰될 것이다. (2) 시간별 강우 강도의 미래 변화가 일단위 강우 강도보다 더 크다. (3) 강우 강도의 불확실성을 정량화하기 위해 앙상블을 사용해야 한다. (4) 강우 강도의 미래 변화에 대한 공간적인 경향이 확인된다. 시단위 시계열 앙상블을 생성하여 추정된 IDF 곡선에 대한 정보는 기후 변화의 영향을 평가하고 적절한 적응 및 대응 전략을 개발하는 데 도움이 될 것이다.

• Journal of Oral Medicine and Pain
• /
• v.31 no.3
• /
• pp.211-221
• /
• 2006

Purpose The aims of this study were to evaluate micro-tensile bond strength of composite resin bonded to dentin following high-speed rotary handpiece preparation or Er:YAG laser preparation with two different adhesive systems and to assess the influence of different Er:YAG laser energies on the micro-tensile bond strength. Materials and Methods In this study, 40 third morlars were used. Flat dentin specimans were obtained and randomly assigned to eight groups. Dentin surfaces were prepared with one of four cutting types: carbide bur, Er:YAG laser (2 W, 3 W and 4 W) and conditioned with two bonding systems, Scotchbond Multipurpose Plus (SM), Clearfil SE bond (SE) and composite resin-build ups were created. After storage for 24 hours, each specimen was serially sectioned perpendicular to the bonded surface to produce more than thirty slabs in each group. Micro-tensile bond strength test was performed at a crosshead speed of 1.0 mm/min. Micro-tensile bond strengths (${\mu}TBS$) were expressed as means$\pm$SD. Data were submitted to statistical analysis using two-way ANOVA, one-way ANOVA, Student-Newman-Keuls' multiple comparison test and t-test. Results and Conclusion 1. Regardless of bonding systems, the ${\mu}TBS$ according to cutting types were from highest to lowest : 3 W, 2 W, Bur, and 4 W. In addition, there was no significant difference between Bur and 4 W (p<0.001). 2. Regardless of cutting types, SM showed significantly higher ${\mu}TBS$ than SE (p<0.001). 3. Bonding to dentin conditioned with SM resulted in higher ${\mu}TBS$ for 3 W compared to Bur, 2 W, and 4 W. There was no significant difference between 2 W and Bur (p<0.001). 4. Bonding to dentin conditioned with SE resulted in higher ${\mu}TBS$ for 3 W compared to 2 W, 4 W, and Bur. Bur exhibited significant lower ${\mu}TBS$ than all other cutting types. There were no significant differences between 3 W, 2 W and between 4 W and Bur (p<0.001). 5. The ${\mu}TBS$ of laser cutting groups were shown in order from highest to lowest: 3 W, 2 W and 4 W in two bonding systems. There was no significant difference between 2 W and 3 W in SE (p<0.001). : The ${\mu}TBS$ of composite resin bonded dentin was significantly affected by interaction between the cutting type and bonding system. In the range of 2 W-3 W, cavity preparation of the Er:YAG laser seems to supply good adhesion of composite resin restoration no less than bur preparation. In particular, if you want to use the self-etching system, including Clearfil SE bond for the purpose of a simplification of the bonding procedures and prevention of adverse effects by excessive etching, an Er:YAG laser may offer better adhesion than a bur.

• Journal of the Korea Concrete Institute
• /
• v.25 no.3
• /
• pp.347-354
• /
• 2013

Recently, crushed fine aggregates are being widely used due to the shortage of natural sand. In Korea, the amount of fine particles under 0.08 mm contained in crushed fine aggregates is restricted to be less than 7%, which is similar to the regulations of ASTM but is still very strict compared to the regulations of the other nations. In addition, the crushed aggregates already have in them about 20% of fine particles under 0.08 mm which occurs while they are crushed. The fine particles are not easy to wash out, and also to maximize the use of resources it is deemed necessary to review the possibility of enhancing the limit of the amount of fine particles. Therefore, this study conducted experiments to analyze the characteristics of fine particles under 0.08mm and their influence on the properties of concrete. Experiments using silt and cohesive soil were also done for comparison. In the experiments on fine particles, the methylene blue value was more in the soil dust contained in silt and cohesive soil than in the stone powder contained in crushed fine aggregates. Also, the methylene blue value had a close correlation with packing density and liquid & plastic limit. In the experiments done with concrete, the quantity of high range water reducing agent demanded to obtain the same slump increased as the fine particle substitution rate heightened. However, in the experiment which used stone powder testing the compressive strength and tensile strength of concrete in the same water-cement ratio, there was little change in strength with less than 20% addition of fine particles among the fine aggregates, and no meaningful difference in the amount of drying shrinkage of concrete.