• Composites Research
• /
• v.35 no.6
• /
• pp.463-468
• /
• 2022

The high porosity of the infill pattern of carbon chopped fiber-reinforced Nylon composite structures fabricated by the fused filament fabrication (FFF) type 3D printers determines the mechanical performance of the printed structures. This study experimentally evaluated the mechanical performance of Onyx composite specimens fabricated with a rectangular infill structure under the hot-pressing condition to improve the mechanical properties by reducing the porosity of the infill pattern of the printed structure, and evaluated the best mechanical performance. The hot-pressing conditions (145℃, 4 MPa, 12 min) that induce the most appropriate mechanical properties were found. As a result of microscopic observation, it was confirmed that the infill porosity of the composite specimens subjected to post hot-pressing treatment was effectively reduced. In order to confirm the mechanical performance of the post-treated specimen, a tensile test and a three-point bending test were performed with a control specimen without post-treatment and a specimen printed with the same density and dimensions after post-treatment to evaluate the mechanical properties. As a result of comparison, it was confirmed that the mechanical properties were effectively improved when the post-treatment of hot-pressing was performed.

• Journal of Advanced Navigation Technology
• /
• v.11 no.2
• /
• pp.137-145
• /
• 2007

The flight test of ADS-B is to demonstrate operational benefits to air traffic controllers and pilots when other aircraft data including the aiming altitude is displayed on CDTI. Additionally, This ADS-B study is to provide first operational experience of ADS-B in ATCS environment of South Korea and provide practical information to ATCS before deployment of ADS-B in South Korea is considered. Participation in the flight test has been limited to 2 Aircraft of H University which are installed ADS-B equipment and the ground station has installed in Tae-An airport. This test have been experimented according to the pre-arranged flight procedures of Tae-An airport. As a result of the test, it has shown that the number of radio transmitting and the time of radio occupied between controller and pilot are remarkably reduced. Besides, as both pilot and air traffic controller are able to see the traffic information in the vicinity of the aircraft, the test has demonstrated that it is possible for ADS-B not only to decline the controller's workload, but also to enhance pilot situational awareness in the near future.

• Journal of the Korean Data and Information Science Society
• /
• v.20 no.4
• /
• pp.673-684
• /
• 2009

Lower Prices are offered through sales by telemarketing. This is to serve our customers by the fastest and most appropriate referral product that is most important to attract insurance. Therefore, Considering the time the customer's preferred products and preferred customer for screening and targeting, depending on what is the difference between the premiums. This study of the logistic regression model using datamining techniques, the life insurance companies in outbound telemarketing to support sales of the effect you want to validate. To join existing life insurance companies for the customer response and sales strategy based on the L segment and by age group, family-love insurance, accident insurance, and cancer insurance were in progress for the modeling. Set model based on the progress of the campaign to existing customers marketing methods and how to extract and run the model results has proven the superiority of the model. In addition, over time, depending on the aging model is set to a decline in operating profit to maximize the profits th update the model which was derived.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.7
• /
• pp.601-605
• /
• 2014

Porous conductors are known to demonstrate excellent electrical, mechanical, and chemical resistance. These porous conductors demonstrated potential applications in various fields such as electrodes for supercapacitors, flexible heaters, catalytic electrodes, and sorbents. In this study, we described a pressure sensitive device using conductive and porous sponges. With an extremely simple "dipping and drying" process using a single-walled carbon nanotube (SWCNT) solution, we produced conductive sponges with sheet resistance of < $30k{\Omega}/sq$. These carbon nanotube sponges can be deformed into any shape elastically and repeatedly compressed to large strains without collapse. The pressure sensors developed from these sponges demonstrated high resistance change under pressure of up to a half of their initial resistance.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.159-160
• /
• 2012

지난 30년 동안 플래시 메모리의 주류 역할을 하였던 부유 게이트 플래시 메모리는 40 nm 기술 노드 이하에서 셀간 간섭, 터널 산화막의 누설전류 등에 의한 오동작으로 기술적 한계를 맞게 되었다. 또한 기존의 비휘발성 메모리는 동작 시 높은 전압을 요구하므로 전력소비 측면에서도 취약한 단점이 있다. 그러나 이러한 문제점들을 기존의 Si기반의 소자기술이 아닌 새로운 재료나 공정을 통해서 해결하려는 연구가 최근 활발하게 진행되고 있다. 특히, 플래시 메모리의 중요한 구성요소의 하나인 터널 산화막은 메모리 소자의 크기가 줄어듦에 따라서 SiO2단층 구조로서는 7 nm 이하에서 stress induced leakage current (SILC), 직접 터널링 전류의 증가와 같은 많은 문제점들이 발생한다. 한편, 기존의 부유 게이트 타입의 메모리를 대신할 것으로 기대되는 전하 포획형 메모리는 쓰기/지우기 속도를 향상시킬 수 있으며 소자의 축소화에도 셀간 간섭이 일어나지 않으므로 부유 게이트 플래시 메모리를 대체할 수 있는 기술로 주목받고 있다. 특히, TBM (tunnel barrier engineered memory) 소자는 유전율이 큰 절연막을 적층하여 전계에 대한 터널 산화막의 민감도를 증가시키고, 적층된 물리적 두께의 증가에 의해 메모리의 데이터 유지 특성을 크게 개선시킬 수 있는 기술로 관심이 증가하고 있다. 본 연구에서는 Si3N4/Ta2O5를 적층시킨 staggered구조의 tunnel barrier를 제안하였고, Si기판 위에 tunnel layer로 Si3N4를 Low Pressure Chemical Vapor Deposition (LPCVD) 방법과 Ta2O5를 RF Sputtering 방법으로 각각 3/3 nm 증착한 후 e-beam evaporation을 이용하여 게이트 전극으로 Al을 150 nm 증착하여 MIS- capacitor구조의 메모리 소자를 제작하여 동작 특성을 평가하였다. 또한, Si3N4/Ta2O5 staggered tunnel barrier 형성 후의 후속 열처리에 따른 전기적 특성의 개선효과를 확인하였다.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.33 no.6
• /
• pp.919-928
• /
• 2023

Deep learning technology is used in various fields such as self-driving cars, image creation, and virtual voice implementation, and deep learning accelerators have been developed for high-speed operation in hardware devices. However, several side channel attacks that recover secret information inside the accelerator using side-channel information generated when the deep learning accelerator operates have been recently researched. In this paper, we implemented a DNN(Deep Neural Network)-based MNIST digit classifier on a microprocessor and attempted a correlation power analysis attack to confirm that the weights of deep learning accelerator could be sufficiently recovered. In addition, to counter these power analysis attacks, we proposed a Node-CUT shuffling method that applies the principle of misalignment at the time of power measurement. It was confirmed through experiments that the proposed countermeasure can effectively defend against side-channel attacks, and that the additional calculation amount is reduced by more than 1/3 compared to using the Fisher-Yates shuffling method.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.40 no.11
• /
• pp.1544-1547
• /
• 2011

Lotus (Nelumbo nucifera) leaf is known to be effective for 'overcoming body heat' and stopping bleeding. It is commonly used as a traditional curing plant for the treatment of hematemesis, epistaxis, hemoptysis, hematuria, and metrorrhagia in traditional Chinese medicine. This study investigated on the effect of oral administration of lotus (Nelumbo nucifera) leaf extract on the serum and liver lipid levels of rats fed a high fat diet. Experimental rats were divided into five different experimental groups, including the general diet group (Cont), high fat diet with lotus leaf extract groups (HL40, HL80, HL120), and high fat diet group (HFG). Body weight significantly decreased in the HL120 sample compared to that of Cont. The weights of the livers and kidneys of rats corresponded to the increase in body weight. Total cholesterol and triglyceride contents in liver tissues of rats were lowest in the sample HL120 sample. The levels of total lipids, total cholesterol, and triglycerides in serum were lower in the HL120 sample compared to the HFG.

• Korean Journal of Optics and Photonics
• /
• v.9 no.5
• /
• pp.333-341
• /
• 1998

The novel integrated device, 1.55 ${\mu}{\textrm}{m}$ DR-LD(distrbuted reflector laser diode) integrated EA-MOD (electro-absorption modulator) as light source, is proposed to improve the device yield and its operational performances. This device can be easily fabricated by the selective MOVPE technique and its fabrication processes are almost the same as the reported 1.55 ${\mu}{\textrm}{m}$ DFB-LD(distributed feedback laser diode) integrated EA-MOD except the asymmetric gratings. The static and dynamic properties are investigated simultaneously by solving the transfer matrix method for light propagation, the time-dependent rate equation for carrier change and schr$\"{o}$dinger equation for QCSE (Quantum-Confined Stark Effect). The performances of the proposed device such as output power, chirp, and extinction ratio are compared with those of DFB-LD integrated EA-MOD. Under 10Gb/s NRZ modulation, we obtain that DR-LD integrated EA-MOD. is 30% higher in output power on the on-state, about 50% lower in chirp, and slightly larger in extinction ratio than DFB-LD integrated EA-MOD.-MOD.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.456-456
• /
• 2010

CMOS 소자가 서브마이크론($0.1\;{\mu}m$) 이하로 스케일다운 되면서 단채널 효과(short channel effect), 게이트 산화막(gate oxide)의 누설전류(leakage current)의 증가와 높은 직렬저항(series resistance) 등의 문제가 발생한다. CMOS 소자의 구동전류(drive current)를 높이고, 단채널 효과를 줄이기 위한 가장 효율적인 방법은 소스 및 드레인의 얕은 접합(shallow junction) 형성과 직렬 저항을 줄이는 것이다. 플라즈마 도핑 방법은 플라즈마 밀도 컨트롤, 주입 바이어스 전압 조절 등을 통해 저 에너지 이온주입법보다 기판 손상 및 표면 결함의 생성을 억제하면서 고농도로 얕은 접합을 형성할 수 있다. 그리고 얕은 접합을 형성하기 위해 주입된 불순물의 활성화와 확산을 위해 후속 열처리 공정은 높은 온도에서 짧은 시간 열처리하여 불순물 물질의 활성화를 높여주면서 열처리로 인한 접합 깊이를 얕게 해야 한다. 그러나 접합의 깊이가 줄어듦에 따라서 소스 및 드레인의 표면 저항(sheet resistance)과 접촉저항(contact resistance)이 급격하게 증가하는 문제점이 있다. 이러한 표면저항과 접촉저항을 줄이기 위한 방안으로 실리사이드 박막(silicide thin film)을 형성하는 방법이 사용되고 있다. 본 논문에서는 (100) p-type 웨이퍼 He(90 %) 가스로 희석된 $PH_3$(10 %) 가스를 사용하여 플라즈마 도핑을 실시하였다. 10 mTorr의 압력에서 200 W RF 파워를 인가하여 플라즈마를 생성하였고 도핑은 바이어스 전압 -1 kV에서 60 초 동안 실시하였다. 얕은 접합을 형성하기 위한 불순물의 활성화는 ArF(193 nm) excimer laser를 통해 $460\;mJ/cm^2$의 에니지로 열처리를 실시하였다. 그리고 낮은 접촉비저항과 표면저항을 얻기 위해 metal sputter를 통해 TiN/Ti를 $800/400\;{\AA}$ 증착하고 metal RTP를 사용하여 실리사이드 형성 온도를 $650{\sim}800^{\circ}C$까지 60 초 동안 열처리를 실시하여 $TiSi_2$ 박막을 형성하였다. 그리고 $TiSi_2$의 두께를 측정하기 위해 TEM(Transmission Electron Microscopy)을 측정하였다. 화학적 결합상태를 분석하기 위해 XPS(X-ray photoelectronic)와 XRD(X-ray diffraction)를 측정하였다. 접촉비저항, 접촉저항과 표면저항을 분석하기 위해 TLM(Transfer Length Method) 패턴을 제작하여 I-V 특성을 측정하였다. TEM 측정결과 $TiSi_2$의 두께는 약 $580{\AA}$ 정도이고 morphology는 안정적이고 실리사이드 집괴 현상은 발견되지 않았다. XPS와 XRD 분석결과 실리사이드 형성 온도가 $700^{\circ}C$에서 C54 형태의 $TiSi_2$ 박막이 형성되었고 가장 낮은 접촉비저항과 접촉저항 값을 가진다.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.38 no.2
• /
• pp.129-137
• /
• 2001

Matching pursuit algorithm was successfully demonstrated useful in low bit-rate video coding, However, one of the practical concerns related to applying the matching pursuit algorithm to application is its massive computation required for finding bases whose weighted sum best approximates the given input image. The main contribution of this paper is that we provide a new method that can drastically reduce the computational load without any degradation of image quality. Its main idea is based on reducing the number of inner product calculation required for finding best bases because the complexity of matching pursuit algorithm is due to the exhaustive local inner product calculation. As the first step, we compute a matrix which is the 1-D inner product of the given motion-compensated error input image with the 1-D vertical Gabor functions using the separable property of Gabor bases. In the second step, we calculate length of each vector in the matrix that corresponds to 1-D horizontal Gabor function, and compare the length with the current maximum absolute inner product value so far. According to the result of this comparison, one can decide whether or not to calculate the inner product. Since most of them do not need to calculate the inner product value, one can significantly reduce the computational load. Experimental results show that proposed method reduces about 70% of inner product calculation compared to the Neff's fast algorithm without any degradation of image quality.