• Journal of IKEEE
• /
• v.24 no.4
• /
• pp.1081-1085
• /
• 2020

Instantaneous frequencies (IF) of the AM-FM signal is estimated based on the inflection point detection (IPD) method. Local maxima/minima are detected using the IPD, and they are exploited to find the IF of AM and FM components, respectively. The envelope of the maxima/minima is obtained to estimate the IF of the AM part. And the distance between neighboring maxima (or minima) is used to estimate the IF of the FM component. Computer simulation shows that the proposed method properly estimates the IF of the AM and FM when the signal has fixed frequencies for both parts. In the case of the time-varying IF of the FM part, the estimated IF shows some deviation from the true IF due to the rough sampling effect of the maximum/minimum points. Thus, the post-processing such as the lowpass filtering of the estimated IF is required to refine the resulting IF estimation.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.6
• /
• pp.1199-1206
• /
• 2018

The hybrid phase shifting device is consist of general phase shifter in sub-array and the true time delay inter sub-array. This configuration for phased shifting can efficiently improve the beam squint according to frequencies. However, when an appropriate array configuration is not selected, a gain variation of main lobe for a phased array antenna is occurred. In order to solve these problems, a simplified formula for constructing efficient array based on the system design requirements, such as the fractional bandwidth, the maximum beam steering angle, and limit criterion of the gain variation, was presented.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.1
• /
• pp.125-135
• /
• 2001

A 8$\times$4 microstrip antenna array is designed at 5.3 GHz and its characteristics are investigated with respect to the application in dual polarized synthetic aperture radars. The design is focused on the achievement of a wide bandwidth, a high polarization purity, a low loss, a good isolation and some mechanical requirements suitable for the application. The antenna is fed by a -3 dB tapered feed network, and is composed of dual polarized SSFIP (Strip-Slot-Foam-Inverted Patch) elements with honeycomb and shielding plane. Simulation results for the antenna array are presented and compared with measurements. It is observed that the antenna shows a bandwidth of 80 MHz, a polarization isolation better than 20 dB, an isolation of 40 dB, and good mechanical characteristics.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.10
• /
• pp.2409-2416
• /
• 2014

In this paper, an automatic recognition algorithm for linearly modulated signals like PSK, QAM under noncoherent asynchronous condition is proposed. Frequency, phase, and amplitude characteristics of digitally modulated signals are changed periodically. By using this characteristics, cyclic moments and higher order cumulants based features are utilized for the modulation recognition. Hierarchial decision tree method is used for high speed signal processing and totally 4 feature extraction parameters are used for modulation recognition. In the condition where the symbol number is 4,096, the recognition accuracy of the proposed algorithm is more than 95% at SNR 15dB. Also the proposed algorithm is effective to classify the signal which has carrier frequency and phase offset.

• 한국체육학회지인문사회과학편
• /
• v.58 no.6
• /
• pp.449-459
• /
• 2019

The purpose of this study is to identify how postural mechanics affects postural control on balance and stability by using frequency analysis technique from the kinematic data acquired during the one leg standing posture. For this purpose, the experimental group consisted of two groups, the normal group (n=6) and the national Gymnastics group (n=6). Displacement data of CoP were analyzed by frequency analysis of rambling (RM) and trembling (TR) by FFT signal processing. As a results, there was a significant difference in evaluating the stabilization index between the two groups with the eyes open and closed one leg stnading (p <.05). The cause of the difference was found to be the output of the maximum amplitude of RM (f1) and TR (f2) (p <.05). In particular, in the low frequency RM of 8-9 Hz, which is a natural frequency of signal wave involved in postural feedback feedback, the main frequency appeared to be performs the exercise mechanism of stable brain posture control. And in the high frequency TM of 120-135 Hz, it is considered that the adaptation of the reflective muscle response is minimized to minimize posture shaking. In conclusion, this study provides evidence for the intrinsic main frequencies according to the postural control ability which affects the CNS in one leg standing.

• Composites Research
• /
• v.14 no.1
• /
• pp.1-7
• /
• 2001

In this study, damage evaluation of glass fiber reinforced thermoplastic composites was investigated with acoustic emission method. Specimens of 1.7mm thickness laminate were made from PET and 7 layers o171ass fabrics. Notch and impact loading were added to the specimen and normal tensile test and tensile test with the dead load were carried out. AE signal was measured as the functions of notch ratio to the width0 and impact energy in order to find out the correlation between fracture mode and AE parameters. The result has shown that low amplitude of AE signal was due to the microcrack of matrix and its growth, whereas the amplitude in the mid range was the response to the delamination and interfacial separation. In the range of high amplitude above 90dB. the fracture of glass fabric was found. Tensile strength decreased with increasing notch ratio to the width and impact energy because of tile effect or delamination, the cracking of matrix and stress concentration. In proportion to the size of damaged area. AE signal showed its wider range of frequency and energy as well as increased number of hits.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.7
• /
• pp.891-897
• /
• 2013

In this study, the compressive deformation behaviors of aluminum alloy under high strain rates were investigated by means of a SHPB test. An acoustic emission (AE) technique was also employed to monitor the signals detected from the deformation during the entire impact by using an AE sensor connected to the specimen with a waveguide in real time. AE signals were analyzed in terms of AE amplitude, AE energy and peak frequency. The impacted specimen surface and side area were observed after the test to identify the particular features in the AE signal corresponding to the specific types of damage mechanisms. As the strain increased, the AE amplitude and AE energy increased whereas the AE peak frequency decreased. It was elucidated that each AE signal was closely associated with the specific damage mechanism in the material.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.42 no.2
• /
• pp.23-28
• /
• 2005

This study was to suggest the propagation path loss and predictive model of propagation path analysis in order to apply the frequency in the millimeter-wave band to the real time inter-vehicle communication system. This study was to suppose the case of inter-vehicle communication on the one-way two-lanes road in the big cites with a lot of traffic jams in order to analyze the effect by the reflected wave of multipath. As a simulation of suggested model, it found out that the propagation path by the reflected wave was about 0.1[m]$\sim$5.1[m] longer than the one by the direct wave during the transmission of 100[m] wave direct path. Also, as a result of comparing the propagation path loss, the loss would be about -0.8[dB]$\sim$-4.2[dB] larger in case of wall reflection and -0.8[dB]$\sim$-1[dB] vehicle reflection. From the result above, this researcher found out that the path loss of reflected wave produced by the walls was about -3.2[dB] larger than the path loss produced by the adjacent vehicles.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.5
• /
• pp.516-524
• /
• 1997

The propagation properties of various pulse signal types(square pulse, Gaussian pulse, trapezoid pulse, RF pulse) on coupled microstrip lines are investigated. Numerical integration technique which has its accuracy and is easily simulated, is used to obtain the time domain response of pulse signals. Frequency-dependent characteristics of coupled microstrip line is obtained using Jansen's approximate equation. The propagation properties of pulse signal on coupled microstrip lines is analyzed regarding to its geometric structure (relative permittivity ${varepsilon}_r$ substrate height h, strip width w of the microstrip line) and pulse width ${\tau}$ of signal pulse. The simulation results show that space between two lines is very significant parameter in pulse distortion in comparison of any other parameters. The results of this paper are compatible to the trade-off determination of relative permittivity, substrate height, strip width and pulse width of signal pulse when a design of MIC and MMIC is necessary.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2006.05a
• /
• pp.242-246
• /
• 2006

최근 들어 전 세계적으로 유량측정 분야의 큰 변화의 방향은 자동화이다. 전자, 전기 기술과 정보통신 기술의 발달을 유량측정 분야에 적용하여 자동적으로 유량측정을 수행하고 실시간으로 모든 유량자료를 수집하는 시스템을 구성하려는 연구가 활발하게 진행중이다. 최근에 초음파 유량계와 더불어 자동 유량측정 기법으로 각광을 받고 있는 기법이 유속지수법(index velocity method)이다. 유속지수법의 원리는 매우 간단하다. 수위 기록을 통하여 수위-면적 관계로부터 흐름 단면적을 구하고, 임의의 영역에서 측정된 유속이 단면 평균 유속으로 환산될 수 있다면, 흐름 단면적과 평균 유속에 의해 연속적으로 유량을 구할 수 있다. 유속지수법에서 가장 중요한 것이 전체 평균 유속을 대표할 수 있는 유속지수를 정확하고 효율적으로 측정하는 것이다. 유속지수법에 의한 연속 유량측정 목적으로 최근에 ADVM(Acoustic Doppler Velocity Meter)이 개발되어 이용되고 있다. ADVM은 수중에 초음파를 발사해서 산란체에서 반사되어 돌아오는 초음파의 주파수 편이, 즉 도플러 효과를 이용하여 유속을 측정하는 유속계이다. 본 연구에서는 ADVM을 괴산댐 하류에 위치한 시험하천에 설치하여, 유속지수법에 의한 유량측정기법을 적용하고 그 특성을 분석하였다. 유속지수법으로 측정된 유량을 괴산댐 방류량과 비교한 결과 평균 4.0%의 상대오차를 지니고 있어 비교적 정확한 연속 유량측정이 가능한 것으로 나타났다. 이와 같은 유속지수법을 하천 유량측정에 활용하면 보다 정확한 유량을 연속적으로 자동화하여 측정할 수 있을 것으로 기대된다.연계모형의 한계로 인하여 두 모형의 통합모형이 필요하다. 즉, 강우 혹은 월류유량으로 발생한 지표유량 중 일부분이 과부하가 발생하지 않는 유입구 지점을 통과할 때 배수시스템으로 유입되는 것을 고려할 수 있고, 유입된 유량은 배수시스템 내의 흐름에 반영되도록 배수시스템과 침수해석모형을 통합한 모형 개발이 필요하다. 그러기 위해서는 지표면과 배수시스템에 대한 수리학적 관계를 정립하여야 한다. 본 연구에서는 배수시스템 해석 모형과 도시침수해석 모형을 통합하고, 두 모형간의 유량의 전송과정을 수리학적 관계를 고려한 dual-drainage 도시침수해석모형을 개발하였다. 이를 위해 도시지역 배수시스템 해석 모형으로 널리 이용되고 있는 SWMM모형을 이용하여 지표면으로의 월류량을 산정하고 유입된 지표유량에 대해서 배수시스템에서의 흐름해석을 수행하였다. 그리고, 침수해석을 위해서는 2차원 침수해석을 위한 DEM기반 침수해석모형을 개발하였고, 건물의 영향을 고려할 수 있도록 구성하였다. 본 연구결과 지표류 유출 해석의 물리적 특성을 잘 반영하며, 도시지역의 복잡한 배수시스템 해석모형과 지표범람 모형을 통합한 모형 개발로 인해 더욱 정교한 도시지역에서의 홍수 범람 해석을 실시할 수 있을 것으로 판단된다. 본 모형의 개발로 침수상황의 시간별 진행과정을 분석함으로써 도시홍수에 대한 침수위험 지점 파악 및 주민대피지도 구축 등에 활용될 수 있을 것으로 판단된다. 있을 것으로 판단되었다.4일간의 기상변화가 자발성 기흉 발생에 영향을 미친다고 추론할 수 있었다. 향후 본 연구에서 추론된 기상변화와 기흉 발생과의 인과관계를 확인하고 좀 더 구체화하기