• Korean Journal of Materials Research
• /
• v.10 no.7
• /
• pp.515-521
• /
• 2000

The effect of precipitates on the high temperature tensile properties of cast alloy 718 was investigated by phase extraction method and microstructural observation. The value of tensile strength and elongation gradually decreased with increasing testing temperature up to $760^{\circ}C$. Elongation of the alloy increased, while tensile strength decreased above 76$0^{\circ}C$. The amount of precipitates in the specimen that tensile tested at $760^{\circ}C$ showed maximum owing to stress assisted precipitation. Therefore, the alloy exhibited the lowest value of the elongation and the degree of decrease in yield strength at this temperature due to high flow stress of precipitates. Little amount of precipitate, especially $\gamma$' and $\gamma$＂, resulted in softening of the alloy at the temperature above $760^{\circ}C$.

• The Journal of Korean Academy of Prosthodontics
• /
• v.50 no.2
• /
• pp.85-91
• /
• 2012

Purpose: The object of this study was to determine if the low-priced alloy and metal UCLA abutment could be available for manufacturing bar-retained framework of implant prosthesis. Materials and methods: Bar structure was classified into 4 groups, The specimen of group 1 and 2 were based on casting high noble metal alloys and noble metal alloys with gold UCLA abutment. The specimen of group 3 and 4 were based on casting noble metal alloys and base metal alloys with metal UCLA abutment. Cast bar structure was installed in an acrylic resin model and only the screw on the hexed abutment side was tightened to 20 Ncm. On the opposite side, vertical discrepancy was measured with stereo microscope from front, back, and lateral side of the implant-abutment interface. One-way ANOVA was performed to analyze the marginal fit discrepancy. Results: One-way ANOVA test showed significant differences among all groups ($P$<.05) except for Group 1 and 3. Among them, difference between Group 1 and 2 was noticeable. Measured vertical discrepancies were all below $70{\mu}m$ except to Group 2. Conclusion: Base metal alloy and metal UCLA abutment could be used as an alternative to high-priced gold alloy for implant bar-retained framework.

• The Journal of the Korea Contents Association
• /
• v.19 no.10
• /
• pp.353-363
• /
• 2019

This study is for the use of color recommendation system for the color combination of mobile application. For this study, color combination methods of a material design color system that recommends harmonized colors automatically and of a mobile web application were applied to a mobile application design and a color combination experiment was carried out. Then for a survey on the experiment using the two methods, color combinations, selected colors and satisfaction with outputs were investigated on a 7-point Likert scale. And color combination characteristics of outputs were compared. It was found that the material design color palette made it easy to select colors by systematizing the regular coloring stages of fixed colors automatically, but there were differences in color compositions and color scopes of dominant color, assort color and accent colors, which are three-color combinations of mobile web application and accent color selection function was required for each design, since only primary colors and secondary colors could be selected. Moreover, chromatic colors were used a lot in the material system because of the fixed color scopes and color combination scopes and images of color combination outcomes varied depending on the color combination scopes, even when tones with a big contrast or complementary colors were selected. The role of color composition was important according to the color combination scopes.

• The Journal of Korean Academy of Prosthodontics
• /
• v.50 no.1
• /
• pp.29-35
• /
• 2012

Purpose: The purpose of this study was to analyze temperature change along the implant-bone interface induced by grinding the occlusal surface of implant gold prosthesis and to compare the temperature generated by grinding of prosthesis with different cooling methods. Materials and methods: The experimental gold prostheses were fabricated with dental gold alloy and castable abutment. The prostheses had 3 cylindrical protrusions on the occlusal surface with 1mm in height. Temperature was measured using 16 thermocouple wires attached to the implant fixture surface and the fixture was embedded in an acrylic resin block inside the $37^{\circ}C$ water bath. Cylinders were grinded for a period of 30 second with a low-speed handpiece with green stone point. One cylindrical protrusion was grinded without cooling, the second one was grinded with air blow, and the third one was grinded with water-spray. Results: The mean maximum temperature was measured more than $47^{\circ}C$ of the implant and the maximum temperature was measured at the cervical portion of the implant in the group without cooling. There was statistically significant difference between the group without cooling and the groups with cooling (P<.05). However, there was no significant difference at all portion of implant in the groups with cooling (P>.05). Conclusion: The results of this study support that the grinding of implant gold prosthesis without cooling may damage the peri-implant tissue. The continuous use of air blow and water-spray adjacent to prosthesis during the grinding of implant gold prosthesis may prove to be beneficial for cooling of the implant.

• Journal of Conservation Science
• /
• v.25 no.4
• /
• pp.411-420
• /
• 2009

A series of scientific analyses, including ICP-AES, microstructure, and TIMS, were carried out on 5 bronze spoons among 14 bronze artifacts excavated from the Ok-dong site in Andong, North Gyeongsang Province. The results of analysis showed that the bronze spoons were formed from an alloy of no more than 75% Cu and 21~23% Sn, placing it in the category of brassware, with trace elements such as Pb, Fe, and Zn. In particular, plumbum Pb contents of which traces of 0.04% were found, appears to have been added as an impurity during smelting. The microstructure of the bronze spoons suggests that the casting process involved using a spoon-shaped hollow mold, followed by an ropid-cooling process after the shape was perfected at approximately $586^{\circ}C$. After comparison of data measured from thermal ionization mass spectrometry (TIMS) of galena from Korea, China, and Japan, it appears that the raw materials for the bronze spoons included galena (lead sulfide) produced from the southern part of China.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.3
• /
• pp.246-252
• /
• 2014

This study is on the development of 150PS inboard type of compact water jet propulsion system. The water jet is composed of intake, impeller, diffuser, reverse bucket and main shaft. Components of water jet have been manufactured through precision processing after sand casting. Development of water jet propelled engine has been finally completed by processes which are design, production and inspection on each component. The water jet performance characteristics show that 0.29 m3/s of maximum flow rate and 37 m/s of flow velocity have been secured in the ground test pool. Field test was performed by 21ft test ship that water jet propulsion equipment developed in this study was installed. As a result, the weight of hull, engine and other parts of the ship has been almost 1.2 ton and 45 km/h of maximum sailing speed has been recorded with 3700 rpm of engine in the domestic coast test.

• Resources Recycling
• /
• v.27 no.3
• /
• pp.48-57
• /
• 2018

In this study, we developed a method for manufacturing high strength gray cast irons by adding a rare earth element (R.E.) included in a spent permanent magnet scrap to gray cast irons. The improvement of the mechanical properties of gray cast irons is attributed to A-type graphite formation promoted by complex sulfide, which was formed by R.E. in the spent magnets during a solidification process. The cast specimen inoculated by R.E. in the spent magnet scrap showed excellent tensile strength up to 306 MPa, and is similar to that of the specimen inoculated by expensive misch-metal. In this regards, we concluded that the cheap spent magnets scrap is a very efficient inoculation agent in fabrication of high performance gray cast irons.

• Journal of Conservation Science
• /
• v.30 no.1
• /
• pp.81-93
• /
• 2014

As the Seated Iron Buddha Statues, Vairocana Buddha of Dopiansa Temple in Cheolwon, Nosana Buddha of Samhwasa Temple in Donghae and Sakyamuni of Mangisa Temple in Pyeongtaek were made during Unified Silla to Koryo Dynasty. These are damaged degradation which are crack, break-out, peel off and various pollutant. As a result of deterioration evaluation using radiography, crack, gap, break-out, pore space and restoration material are confirmed inside in the Buddha Statues. Based on iron strength, the Buddha Statues will be maintain current state as long as a high external impact is not applied. Also, iron core and nails used for fixing of internal and external framework were observed in the Buddha Statues. According to prominent line of surface, embossed inscription, hands cast separately and combined, the Buddha Statues were made by using division casting.

• Korean Journal of Food Science and Technology
• /
• v.15 no.4
• /
• pp.326-332
• /
• 1983

Acorn wine was manufactured experimentally with koji inoculated the strain producing acorn tannin hydrolyzing enzyme in order to apply fungal tannase to food processing. Starch value of several Korean acorns was found to be 72.84 and the acorns were worthy of use as a carbohydrate food. Mixed koji was prepared by combination of rice and acorn powder at a ratio of 50to 50 and inoculation of Aspergillus oryzae producing amylase and Aspergillus sp. AN-11 producing tannase into the mixture in order to hydrolyze efficiently acorn tannin inhibiting alcohol fermentation in the medium, and then the mixed koji was used as a suitable koji to manufacture acorn wine. Acorn wine brewed with medium of the acorn powder treated with water and cooked and the mixed koji prepared was superior about two times to that brewed with medium of untreated acorn powder and general koji with respect to the rate of alcohol production and sugar fermentation during the 1st and 2nd brewing.

• The Journal of Korean Academy of Prosthodontics
• /
• v.40 no.2
• /
• pp.156-171
• /
• 2002

The purpose of this study was to measure and compare the strains produced by screw-tightening implant frameworks fabricated by aye different fabrication methods; (1) one-piece cast using plastic sleeve, (2) one-piece cast using gold cylinder, (3) laser welding, (4) soldering, and (5) electrical discharge machining, and also to measure and compare the strains produced when the order of screw tightening was changed A research model incorporating eighteen strain gages was made to measure the fit of implant frameworks in three dimensions. Three implants aligned in an arc were fixed on the top ends of the L-shape aluminum bars of the research model, and standard abutments were joined to the implants with abutment screws. Five types of implant framework were placed on the abutments and screwed by a torque wrench using 10 Ncm. Under the conditions of this study, the following conclusions were drawn: 1. The electrical discharge machining group showed the smallest magnitude of strain, followed by the soldering group, the laser welding group, the one-piece cast group using gold cylinder, and the one-piece cast group using plastic sleeve. However, among the magnitude of strain for the remaining groups except the electrical discharge machining group, there were not significant differences. 2. When the order of screw tightening was changed, there were not significant differences in the magnitude of strain. 3. In comparison with the electrical discharge machining group, the laser welding group and the one-piece cast groups showed greater horizontal distortion and the soldering group showed greater horizontal and vertical distortion.