• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.8
• /
• pp.4707-4712
• /
• 2014

Considerable fuel in cars is consumed by air resistance. The flow resistance against the air stream was analyzed by flow analysis near the passenger car body. In this study, the models were used were cars available on the real market. Two velocities entered into inlet plane of flow were 80 km/h and 110 km/h using the flow analysis of CFX. As the study method, the velocity of air flow near the car and the pressure on the rear part of car body were investigated at the driving of car. The shapes of the study models were models 1 and 2, and the flow streams were four cases of 1, 2, 3, and 4. In case 1 among the four cases, the maximum pressure ($1.017{\times}10^5Pa$) on the rear part was highest and the maximum velocity (43.81m/s) of air flow near car body was fastest. The air drag force in the case of high speed (110km/h) driving a passenger car was higher than that of a normal driving speed (80km/h). The drag force at wide section area of the car body becomes higher than the narrow section area. The shape of the car body can be effectively designed to reduce the air resistance using the study results of this analysis.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.13 no.4
• /
• pp.9-15
• /
• 2009

The flow of combustor in scramjet engine has supersonic speed so that the residence time and mixing ratio are very important factors for the efficient combustion. This study used open cavity(L/D=4.8) as a fuel/air mixing model. Laser schlieren visualization and pressure measurement were carried out to observe the flow characteristics around a jet orifice and a cavity at the time of fuel injection. As a result of 10ns laser schlieren, unsteady flow which was around the cavity could be observed effectively. Pressure was measured that momentum flux ratio(J) was changed. And the change of critical ignition point could be observed by the momentum flux ratio changed.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.72.1-72.1
• /
• 2010

지금까지 연료전지 시스템의 효율을 극대화시키기 위한 기술들이 개발되어 왔는데, 대표적인 방법은 CHP(Combined Heat & power)와 FCT(Fuel cell & Turbine) Hybrid 시스템이다. 그러나 본 연구의 기술은 연료전지 배열을 이용한 Coanda 공기증폭기를 장착한 새로운 개념의 고효율 연료전지 시스템이다. 원래 공기 증폭기는 완만한 곡면 주위를 흐르는 유체가 곡면의 표면을 따라 흐름의 방향이 바뀌는 원리(Coanda Effect)를 이용한 장치로서, 소량의 고압유체를 구동 에너지원으로 사용하여 최고 20배에 해당하는 많은 양의 주변 유체를 빠른 속도로 이송시키는 역할을 한다. 문제는 고압의 유체원을 만드는 것인데, 본 연구에서는 발전용 연료전지 시스템의 배기가스를 활용하여 먼저 고압의 수증기를 발생시키고, 다음으로 고압의 수증기를 공기 증폭기의 구동원으로 사용함으로써 연료전지 시스템의 Air blower를 대체하는 것이다. 이러한 개념을 검증하기 위해서 고압의 스팀작동 Coanda 공기증폭기를 제작하여 선행실험을 진행하였다. 먼저 공기증폭기의 Gap 및 스팀압력에 따른 공기유량, 압력 등의 기본특성을 조사하였고, 출력 공기의 특성을 개선하기 공기증폭기의 형상 및 재료를 새롭게 설계하였다. 그리고 실제 시스템의 적용가능성을 알아보기 위해서, 예로 300kW급 용융탄산염 연료전지 발전시스템의 Air blower 대체가능성을 확인하였고, 배열이용 Coanda 공기증폭기를 활용한 고효율 연료전지 시스템의 개념설계를 수립하였다. 결론적으로 본 기술을 활용하면 연료전지 시스템의 최종 전기효율을 향상시킬 뿐 아니라는 시스템의 장기 신뢰성을 증대시키는 효과를 기대할 수 있다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.6
• /
• pp.649-654
• /
• 2010

A three-dimensional numerical study of the WIG-effect vehicle with a direct-underside-pressurization (DUP) system and a propeller is performed to analyze the aerodynamic forces and moments acting on the vehicle. The computational model includes all the compartments of a WIG-effect vehicle, including a propeller in the middle of the fuselage and an air chamber under the fuselage. The DUP system and propeller help considerably reduce the take-off speed and minimize the effect of the hump drag when the vehicle accelerates to take off on water. The airflow is accelerated by a propeller, and the air then enters the air chamber through a channel in the middle of the fuselage, this air helps increase the lift since the dynamic pressure of air is converted to static pressure. However, the air accelerated by the propeller produces excessive drag and creates yawing moment. It is found that the effect of yawing and rolling moments on static stability is negligible.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.281-284
• /
• 2008

The flow of combustor in scramjet engine is supersonic speed. So residence time and mixing ratio are very important factors for efficient combustion. This study used open cavity on fuel/air mixing model and laser schlieren was carried out to investigate flow characteristics around a jet orifice and a cavity. A source of illumination has 10 ns endurance time so it can observe unsteady flow characteristics efficiently. Pressure was measured by varying momentum flux ratio. And the change of critical ignition point was observed to change of momentum flux ratio.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.2
• /
• pp.60-68
• /
• 1996

디젤 엔진의 분사연료를 연소실 내부에 마련된 작은 돌출부에 충돌시켜 액적을 작게 부수고 연료가 연소실 내부에 고루 분포할 수 있도록 하여 여러 가 지 엔진성능향상을 도모한 새로운 디젤 연소실 시스템이 최근 제시되고 있다. 이들 시스템은 피스톤 내부 혹은 엔진헤드 부위에 분사연료 충돌부를 두고 있는데, 여기에서는 이 새로운 시스템 개발에 있어 고려되어야 할 몇 가지 중요 요인들에 중점을 두어 분석하였다. 결과로서 분사압력, 사노즐크기, 주위공기 온도와 압력의 변화가 분무 평균입경과 분무연료의 분포에 미치는 영향을 제시하였다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.650-654
• /
• 1997

This paper presents the experimental results of air pressure analysis around a high speed and large package pirn. The experimental system is constructed to measure around air pressure of a rotating pirn in highspeed. The experiment is carred out for the varios speeds. The results that, air pressure around rotating pirn increases as the speed increase, air prissure on the midle of the prin is larger than that on the both ends, and the force direction is opposite to the rotation dirction. The present results a useful to design the high speed, large package pirn winder.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.04a
• /
• pp.8-8
• /
• 1999

2-유체 인젝터의 분무연소에 대한 통찰 및 구조에 대한 이해와 연료-공기 혼합과 연소반응의 물리적 이해에 필요한 수치적 모델의 개발 및 검증을 위해서는 2유체 시스템에서 액체 및 기체 각각의 기본적 특성인 액적크기, 액적속도, 액적의 질량플럭스(flux), 가스상의 속도측정 등이 필요하다. 특히, 액체분무에서는 액적의 크기를 예측하는 것이 매우 중요한 과제이며, 액적의 크기에 영향을 주는 인자들로는 노즐의 형태, 분사액체의 물성치(점도, 표면장력, 밀도), 주위기체의 조건(온도, 압력, 응축과 증발현상), 분사압력 등이 있다. 그러나, 실제 분무액적의 크기는 분포를 가지므로 같은 SMD를 가지더라도 그 분포의 정도는 크게 다를 수 있어 결과적으로 분무액적의 크기를 평균값만으로 표현하는 것은 불충분할 뿐만 아니라 그 적용에도 한계를 가지게 된다. 따라서 분무액적의 평균크기와 함께 그 분포의 정도 등을 함께 나타내려는 시도가 많은 과학자들에 의하여 연구되었다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.7
• /
• pp.85-93
• /
• 2003

Droplet vaporization at various ambient pressures is studied numerically by formulating one dimensional evaporation model in the mixture of hydrocarbon fuel and air. The ambient pressure ranged from atmospheric conditions to the supercritical conditions. The modified Soave-Redlich-Kwong state equation is used to account for the real gas effects in the high pressure condition. Non-ideal thermodynamic and transport properties at near critical and supercritical conditions are considered. Some computational results are compared with Sato's experimental data for the validation of calculations. The comparison between predictions and experiments showed quite a good agreement. The droplet lifetime increases with increasing pressure at temperature lower than the critical temperature, however, it decreases with increasing pressure at temperature higher than the critical temperature. The solubility of nitrogen can not be neglected in the high pressure and it becomes higher as the temperature and the pressure go up.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.7
• /
• pp.97-104
• /
• 2006

The spray and breakup characteristics of swirling liquid sheet were investigated by measuring the spray angle and breakup length as the axial Weber number Wel was increased up to 1554 and the ambient gas pressure up to 4.0MPa. As Wel and ambient gas density increased, the disturbances on the annular liquid sheet surface were amplified by the increase of the aerodynamic forces, and thus the liquid sheet disintegrated near from the injector exit. The measured spray angles according to the ambient gas density were different before and after the sheet breaks. Before the liquid sheet breaks, the spray angle was almost constant, but once the liquid sheet started to breakup, the spray angle decreased. And the breakup length decreased because of the increase of the aerodynamic force as the ambient gas density and Wel increased. Lastly, the measured breakup length according to the ambient gas density and Wel was compared with the result by the linear instability theory. We found that the corrected linear instability theory considering the attenuation of sheet thickness agrees well with our experimental results.