• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.16 no.2
• /
• pp.149-158
• /
• 1998

The aim of this paper is to propose the technique of the two dimensional geodetic coordinates conversion between WGS84 and Bessel spheroids by the two-dimensional affine transformation modeling based on the UTM plane coordinates without the local geoid model which is essential to three dimensional coordinates conversion. Area of approximately $25\times{11}$ square km in the city of Inchon was selected as the test area. The transformation parameters were determined using the eleven triangulation control points in test area. And then, those paraneters were applied to the fifteen cadastral control points which selected as checking points for precision checking of transformation parameters. The average and standard deviations of the absolute values of the conversion residuals of checking points in latitude/longitude and N/E(UTM) and/or x/y(TM) are $\pm0.006"$$\pm0.013"$ and $\pm{17cm/}\pm{30cm}$ respectively. Also, coefficients for 7-parameters, 3-parameters and UTM model transformation computed according as sizes of transformed area, and then the transformed characteristics of checking points according to transformation methods analyzed synthetically.hetically.

• Journal of Cadastre & Land InformatiX
• /
• v.45 no.2
• /
• pp.45-56
• /
• 2015

The main purpose of this investigation is to make up for the limitations of parcel addressing and to seek the application plan of cadastral triangulation point to effective installation of national index numbers. The test-bed has been constructed at the mountainous area located in Nowon-gu, seven cadastral triangulation points within the test-bed was directly applied to this investigation. Each points have been firstly converted from a plane rectangular coordinates to a single plane rectangular coordinates (UTM-K). To verify positioning results achieved from these points, a single plane rectangular coordinates through the Network-RTK was considered. With regards to verification result, maximum coordinate shift was revealed by 6 cm, this level of difference can be satisfied to Article 7, paragraph 2 "the regulation for National Index Number". This means that coordinate transformation applied with cadastral triangulation points can achieve the sastisfied result without local surveying. And also, remarkable effects have been created in terms of financial effectiveness and safe preservation of cadastral triangulation points due to the omission of local surveying.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2018.05a
• /
• pp.137-137
• /
• 2018

표면영상유속계는 매우 간편하고 신속하게 하천의 유속장을 측정하는 기법이지만 하천의 넓은 구역을 카메라로 촬영하기 때문에 영상왜곡이 필연적으로 발생한다. 이러한 왜곡을 보정하기위해 많이 사용되고 있는 2차원 투영좌표변환법을 이용하여 유속을 분석하였다. 하지만 2차원 투영좌표변환법의 경우 표정점이 수표면의 높이와 같은 위치에 존재하지 않으면 유속 분석 결과에 큰 오차를 유발시킨다. 홍수 시 하천의 수위가 급변할 경우 표정점을 수위 변화에 맞추어 이동시키면서 영상을 촬영한다는 것은 현실적으로 불가능하다. 이러한 문제점을 극복하기위해 하천의 수위 변화에 대응하는 영상왜곡 보정 기법 개발이 필요하다. 이에 본 연구에서는 기존의 2차원 투영좌표변환법을 개선하기 위해 제방근처의 표정점 4개와 카메라의 좌표와 카메라와 수표면까지의 연직거리를 이용한 영상왜곡 보정식을 개발하였다. 그리고 표정점과 수표면의 높이를 다양하게 변화시키면서 개발한 보정식을 적용하였다. 표정점이 수위에 맞게 설정된 경우를 기준으로 수위보다 높게 설정된 표정점에 대하여 보정식을 적용한 경우의 유속은 표정점이 수위보다 높게 설정된 경우의 유속과 비교한 결과 오차가 크게 개선되었음을 확인하였다. 따라서 하천에 CCTV를 고정적으로 설치하여 유량을 산정할 경우 본 연구에서 제시한 표정점 보정식을 활용한다면 수위가 급변하는 상황에서도 정확한 표면유속을 산정할 수 있을 것으로 기대한다.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.27 no.2
• /
• pp.281-288
• /
• 2009

In the paper, we try to develop the methodology for updating road networks of large-scale digital maps by using construction drawing data. For the purpose, it is pre-requite step to merge road networks detached in CAD drawing data. As such, tie points are identified in neighboring drawings and used for solving the parameters of 2D conformal transformation between drawings. Then, the merged road network in CAD data is transformed to the coordinate system of digital maps. In the process, IPs in the drawings are considered as control information and 2D affine transformation is selected for coordinate transformation. Through the experiments with real dataset, we can identify that the developed method is valid and generally applicable.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.11 no.4
• /
• pp.163-170
• /
• 1991

The 3 dimensional point positioning from SPOT imagery is performed by bundle adjustment methods of analytical and digital photogrammetry, and need the precise determination of image coordinates and accurate coordinates of ground control points. In this study, the authors analysed the digitized planimetric accuarcy and height accuracy of topographic maps in comparison with accurate coordinates by coordinates resulted by bundle adjustment in each cases between different acquisition method of ground control point coordinates and formats of SPOT imagery.

• Journal of Cadastre & Land InformatiX
• /
• v.46 no.2
• /
• pp.183-196
• /
• 2016

Ground control points are needed for precision geometric correction of satellite images, and the coordinates of a high-quality ground control point can be obtained from the GPS measurement. However, considering the GPS measurement requires an excessive amount o f t ime a nd e fforts, there is a need for coming up with an alternative solution to replace it. Therefore, we examined the possibility of replacing the existing GPS measurement with coordinates available at online maps to acquire the coordinates of ground control points. To this end, we examined error amounts between the coordinates of ground control points obtained through Daum Map API, and them compared the accuracies between three types of coordinate transformation equations which were used for geometric correction of satellite images. In addition, we used the coordinate transformation equation with the highest accuracy, the coordinates of ground control point obtained through the GPS measurement and those acquired through D aum M ap A PI, and conducted geometric correction on them to compare their accuracy and evaluate their effectiveness. According to the results, the 3rd order polynomial transformation equation showed the highest accuracy among three types of coordinates transformation equations. In the case of using mid-resolution satellite images such as those taken by Landsat-8, it seems that it is possible to use geometrically corrected images that have been obtained after acquiring the coordinates of ground control points through Daum Map API.

• The Korean Journal of Applied Statistics
• /
• v.28 no.3
• /
• pp.485-494
• /
• 2015

Canonical correspondence analysis is an ordination method used to visualize the relationships among sites, species and environmental variables. However, projection results are fluctuations if the samples slightly change and consistent interpretation on ecological similarity among species tends to be difficult. We use the bootstrap methods for canonical correspondence analysis to solve this problem. The bootstrap method results show that the variations of coordinate points are inversely proportional to the number of observations and coverage rates with bootstrap confidence interval approximates to nominal probabilities.

• 한국지형공간정보학회:학술대회논문집
• /
• 1997.12a
• /
• pp.17-25
• /
• 1997

스트립 방식으로 촬영된 위성영상의 기하학적 모델링시에는 일반적으로 단위모델별로 위성영상에서 식별이 용이한 지점을 지상기준점으로 선정하여 영상에서의 좌표를 해석도화기나 컴퓨터 화면상에서 획득하고, 그에 대응하는 지상좌표는 현지측량이나 기본지도로부터 얻는다. 현지측량방법의 경우에는 정확하고 신뢰성있는 좌표를 제공해 줄 수 있는 반면에 현지로의 접근이 용이해야 하고 비용과 시간이 많이 소요되며, 소축척의 기본지도상에서 직접 독취하는 경우에는 지도자체에 내재된 오차의 정도가 불명확하고 지상기준점으로 선정한 지점이 명확히 표기되어 있지 않은 경우가 있으므로 영상좌표 측정시에 오차의 유발 가능성이 크다. 특히 영상 해상도 $5{\sim}10m$의 연속된 화상을 3차원 기하학적 모델링을 수행하기 위하여 현지측량에 의해 지상기준점을 획득하는 방법은 경제성 및 효율성 측면에서 불리하다. 따라서 본 연구에서는 삼각점 조서를 이용하여 연속촬영된 SPOT 위성영상을 스트립 단위로 모델링하여 영상해상도 수준의 위치정확도를 얻을 수 있는 연속화상 모델링기법을 제시하였다.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.25 no.4
• /
• pp.299-307
• /
• 2007

This study is about the calculation of practical orthometric height for permanent GPS station. We presented the method to determine the orthometric height precisely by combining leveling data, GPS data and gravimetry data, and determined the orthometric heights of thirty GPS stations. To test the result we developed the expected error model fur the determined orthometric heights regarding the accuracy of Korean national benchmarks and the precision of surveying methods used at this project. The reliability of the results was presented by comparing it with expected error model statistically.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.25 no.6_2
• /
• pp.613-623
• /
• 2007

The main purpose of this study is to investigate the coordinate transformation based on two different systems between local geodetic datum(tokyo datum) and international geocentric datum(new Korea geodetic datum). For this purpose, three methods were used to determine seven parameters as follows: Bursa-Wolf model, Molodensky-Badekas model, and Veis model. Also, we adopted multiple regression equation method to convert from Tokyo datum to KTRF. We used 935 control points as a common points and applied gross error analysis for detecting the outlier among those control points. The coordinate transformation was carried out using similarity transformation applied the obtained seven parameters and the precision of transformed coordinate was evaluated about 9,917 third or forth order control points. From these results, it was found that Bursa-Wolf model and Molodensky-Badekas model are more suitable than other for the determination of transformation parameters in Korea. And, transforming accuracy using MRE is lower than other similarity transformation model.