• Journal of Korean Society of Steel Construction
• /
• v.29 no.2
• /
• pp.111-122
• /
• 2017

In this paper, the applicability of a 1900mm-deep concrete-filled U-shaped composite beam to composite ordinary moment frames (C-OMFs) was investigated based on existing test results from smaller-sized specimens and supplemental numerical studies since full-scale seismic testing of such a huge sized beam is practically impossible. The key issue was the web local buckling of concrete-filled U section under negative bending. Based on 13 existing test results compiled, the relationship between web slenderness and story drift capacity was obtained. From this relationship, a 1900mm-deep mega beam, fabricated with 25mm-thick plate was expected to experience the web local buckling at 2% story drift and eventually reach a story drift over 3%, thus much exceeding the requirements of C-OMFs. The limiting width to thickness ratio according to the 2010 AISC Specification was shown to be conservative for U section webs of this study. The test-validated supplemental nonlinear finite element analysis was also conducted to further investigate the effects of the horizontal stiffeners (used to tie two webs of a U section) on web local buckling and flexural strength. First, it is shown that the nominal plastic moment under negative bending can be developed without using the horizontal stiffeners, although the presence of the stiffeners can delay the occurrence of web local buckling and restrain its propagation. Considering all these, it is concluded that the 1900mm-deep concrete-filled U-shaped composite beam investigated can be conservatively applied to C-OMFs. Finally, some useful recommendations for the arrangement and design of the horizontal stiffeners are also recommended based on the numerical results.

• Journal of the Korean earth science society
• /
• v.28 no.1
• /
• pp.64-74
• /
• 2007

The marine seismic prospecting using a research vessel in the shallow sea near the coastal area has certain limits according to the water depth and survey environment. Also, for the electrical resistivity survey at seashore area, one may need a specially designed high-voltage source to penetrate the very conductive surface layer. Therefore, we have conducted a feasibility study on the application of magnetotelluric method (MT), a passive geophysical method, on investigating of shallow marine environment geology. Our study involves both theoretical modeling and field survey at the tidal flat area which represent the very shallow marine environment. We have applied the audio-frequency magnetotelluric (AMT) method to the intertidal deposits of Gunhung Bay, west coast of Korea, and analysed the field data both qualitatively and quantitatively to investigate the morphology and sedimentary stratigraphy of the tidal flat. The inversion of AMT data well reveals the upper sedimentary layer of Holocene intertidal sediments having a range of 13-20 m thickness and the erosional patterns at the unconformable contact boundary. However, the AMT inversion results tend to overestimate the depth of basement (30-50 m) when compared with the seismic section (27-33 m). Since MT responses are not significantly sensitive to the resistivity of middle layer or the depth of basement, the AMT inversion result for basement may have to be adjusted using the comparison with other geophysical information like seismic section or logging data if possible. But, the AMT method can be an effective alternative choice for investigating the seashore area to get important basic informations such as the depositional environment of the tidal flat, sea-water intrusion and the basement structure near the sea shore.

• Archives of design research
• /
• v.16 no.1
• /
• pp.181-198
• /
• 2003

The purpose of this study is to develop a on-line design tool for effectively coping with e-Business environment, or product design process into a Cyber model for traditional manufacturers which attempts new product development under such environment. It was finally developed as a model named $\ulcorner$Design Vortal Site; e-BVDS) that was based on the structure and style of internet web site. Results of the study can be described as follows ; \circled1 e-Business is based on the Internet. All processes in the context of e-Business require models whose structure and method of use are on-line styles. \circled2 In case that a traditional manufacturing business is converted into e-Business, it is better to first consider Hybrid Model that combines resources and advantages of both such traditional and digital businesses. \circled3 The product design process appropriate for e-Business environment has to have a structure and style that ensure utilization of the process as an Internet web site, active participation by product developers and interactive communication between participants in designing and designers. \circled4 $\ulcorner$e-BDVS) makes possible the use of designers around the wend like in-house designers, overcoming lack in creativity, ideas and human resources traditional business organizations face. However, the operation of $\ulcorner$e-BDVS$\lrcorner$ requires time and budget investments in securing related elements and conditions. \circled5 Cyber designers under $\ulcorner$e-BDVS$\lrcorner$ can easily perform all design projects in cyber space. But they have some limits in playing a role as designers and they have difficulty in getting rewards if such projects completed by them are not finally accepted. \circled6 $\ulcorner$e-BDVS) ensures the rapid use of a wide range of design information and data, reception of a variety of solutions and ideas and effective design development, all of which are not possible through traditional processes. However, this process may not be suitable to be used routine process or tool. \circled7 $\ulcorner$e-BDVS$\lrcorner$ makes it possible for out-sourcing or partners businesses to overcome restrictions in time and space and improve productivity and effectiveness. But such they may have to continue off-line works that can not be treated on-line.

• The korean journal of orthodontics
• /
• v.26 no.2 s.55
• /
• pp.163-174
• /
• 1996

The purpose of this study was to examine the effects of bisphosphonate and indomethacin, blockers of bone resorption with different mechanisms, on alveolar bone remodeling. Male rats were divided into control, bisphosphonate and indomethacin groups, and then each group was divided info an experimental side and a control side according to the force application. Bisphosphonate(6.3mg/kg,$2.52x10^{-2}mol/L$) and indomethacin (9mg/kg, $2.52x10^{-2}mol/L$) were injected 6 hours and 1 hour before or 24 hours after the force application. The rats were killed 72 hours after the force application and histologic examination was perfomed. The values of serum acid phosphatase and lactate dehydrogenase were also measured in the control md experimental groups treated with bisphosphonate or indomethacin 1 hour before the force application. In the experimental side, the least number of osteoclasts was noted in the groups treated 1 hour before the force application with indomethacin or bisphosphonate, while there were no differences between the control and the groups treated with drugs 6 hours before or 24 hours after the force application. In the control side, the number of osteoclasts was not inecreased with no differences among the groups. Histologic examination revealed a severe alveolar bone resorption in the control group and the groups treated with indomethacin 6 hours before or 24 hours after the force application. Indomethacin treatment 1 hour before the force application and bisphosphonate treatment at any time significantly attenuated the bone resorption. Electron microscopically, ruffled border and clear zone of osteoclasts were observed in the control and indomethacin groups, while some osteoclasts were detached from the bone surface and exhibited dull cellular projections in the bisphosphonate groups. The bisphosphonate and indomethacin groups showed lower values of acid phosphatase and lactate dehydrogenase than the control group. The acid phosphatase value in the bisphosphonate group was lower than that in the indomethacin group, whereas there was no difference in the lactate dehydrogenase value between the groups. These results suggest that bisphosphonate reduces the activity of osteoclasts as well as the number of osteoclasts and that indomethacin reduces the number of osteoclasts without affecting the activity of osteoclasts. Bisphosphonate has a larger inhibitory effect on bone resorption md thus less limitation in the application time than indomethacin.

• Radiation Oncology Journal
• /
• v.16 no.1
• /
• pp.71-79
• /
• 1998

Purpose : The objective of this study is to introduce our installation of a non-commercial 3D Planning system, Plunc and confirm it's clinical applicability in various treatment situations. Materials and Methods : We obtained source codes of Plunc, offered by University of North Carolina and installed them on a Pentium Pro 200MHz (128MB RAM, Millenium VGA) with Linux operating system. To examine accuracy of dose distributions calculated by Plunc, we input beam data of 6MV Photon of our linear accelerator(Siemens MXE 6740) including tissue-maximum ratio, scatter-maximum ratio, attenuation coefficients and shapes of wedge filters. After then, we compared values of dose distributions(Percent depth dose; PDD, dose profiles with and without wedge filters, oblique incident beam, and dose distributions under air-gap) calculated by Plunc with measured values. Results : Plunc operated in almost real time except spending about 10 seconds in full volume dose distribution and dose-volume histogram(DVH) on the PC described above. As compared with measurements for irradiations of 90-cm 550 and 10-cm depth isocenter, the PDD curves calculated by Plunc did not exceed $1\%$ of inaccuracies except buildup region. For dose profiles with and without wedge filter, the calculated ones are accurate within $2\%$ except low-dose region outside irradiations where Plunc showed $5\%$ of dose reduction. For the oblique incident beam, it showed a good agreement except low dose region below $30\%$ of isocenter dose. In the case of dose distribution under air-gap, there was $5\%$ errors of the central-axis dose. Conclusion : By comparing photon dose calculations using the Plunc with measurements, we confirmed that Plunc showed acceptable accuracies about $2-5\%$ in typical treatment situations which was comparable to commercial planning systems using correction-based a1gorithms. Plunc does not have a function for electron beam planning up to the present. However, it is possible to implement electron dose calculation modules or more accurate photon dose calculation into the Plunc system. Plunc is shown to be useful to clear many limitations of 2D planning systems in clinics where a commercial 3D planning system is not available.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.47 no.2
• /
• pp.117-132
• /
• 2019

The study examines the significance and limits of modern park planning by analyzing major planning documents of Gyeongseong in the Japanese colonial era. Among seven selected documents from 1925 to 1940, which show the contents related with park planning, documents of 1930 and 1940 presented the official park plan of Gyeongseong. By the 1920s, the park plan was not a major concern in urban planning of Gyeongseong; however, as the planning law as enacted in 1934, the park plan legally became a part of the official master planning process in the 1930s. In 1940, the most comprehensive park plan for Gyeongseong was published. In the beginning of modern urban planning, a park was mainly perceived as a sanitation utility. From the 1920s to the 1930s, the park planning system was significantly improved including systemic classification of parks, guideline development considering spatial planning, and introduction of a concept of infra-structural green space. Despite of the improvement in the park planning, the actual quantity of the overall green spaces barely changed and there was a huge discrepancy between the planning ideal and the reality. The Gyeongseong stadium was the only facility newly built in the 1920s, and only two parks were constructed in the 1930s. The plan to build 38 new parks in the 1930, and 140 in the 1940 was barely realized. However, there were efforts to improve parks and green spaces of Gyeongseong: Such as appropriating natural forest as parks, designating royal palaces as parks, and focusing on constructing smaller scale children's parks. Even though the ideal plan could not be fully implemented due to the war time situation and tight budget, the park system of Gyeongseong provided the framework of park planning of Seoul after the independence.

• The Korean Journal of Archival Studies
• /
• no.24
• /
• pp.215-274
• /
• 2010

Iron-making industries of the country, regardless of age has been the focus. This makes the iron production technology and production techniques that result in increased economic activity and because of the central charge. Therefore, the social development of ancient iron-making technology is based on phase-sensitive. Modern steel making up the monopoly of the country's target under the strict control of production, distribution was. It is essential to produce iron weapons was a threat is because you can keep the throne in the hands of the forces that can cause side effects when I went was to block. This study created a rail Cholbi(iron monument) and the regional distribution pattern of the production, construction background, looked on. Cholbi(iron monument) for the production and recording "the Annals of the Joseon Dynasty" often appear in history books and many academic interests, but was off target. Compared to a stone monument that was not generally as well as the Japanese colonial period and over the course of modernization destroyed, damaged a lot of cases the cause may be found in front. Cholbi(iron monument), except for the gravestones of the Joseon Dynasty monument erected in honor of virtue, as an example of content that dominated a packman business, founding of the school and confirmed that a few were built as a special purpose. Cholbi(iron monument) compared to the production technology or the cost of the monument's difficulty in financing follows. Therefore Cholbi(iron monument) the establishment of the Joseon Dynasty through the background of the economic situation and the local government can look. And iron technology began complaining about the object of history, economic conditions, with the change of season has been a change in people's consciousness tells you. Important data of ancient history as an epigraph that has been as important, the Middle Ages to modern times ranging from newly born to the time Cholbi(iron monument) in the development of the country's documentary subject to change should have been brought. Based on these discussions changes the identity of the hero monument and production inspector, review of production through the Joseon Dynasty period Cholbi (iron monument) contemplated the significance is reflected in production.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.21 no.1
• /
• pp.167-175
• /
• 2019

To effectively deal with the fire in tunnel which is mostly the vehicle fire, it's more important to suppress the fire at early stage. In urban tunnel, however, accessibility to the scene of fire by the fire fighter is very limited due to severe traffic congestion which causes the difficulty with firefighting activity in timely manner and such a problem would be further worsened in underground road (double-deck tunnel) which has been increasingly extended and deepened. In preparation for the disaster in Korea, the range of life safety facilities for installation is defined based on category of the extension and fire protection referring to risk hazard index which is determined depending on tunnel length and conditions, and particularly to directly deal with the tunnel fire, fire extinguisher, indoor hydrant and sprinkler are designated as the mandatory facilities depending on category. But such fire extinguishing installations are found inappropriate functionally and technically and thus the measure to improve the system needs to be taken. Particularly in a double-deck tunnel which accommodates the traffic in both directions within a single tunnel of which section is divided by intermediate slab, the facility or the system which functions more rapidly and effectively is more than important. This study, thus, is intended to supplement the problems with existing tunnel life safety system (fire extinguishing) and develop the remote-controlled automatic fire extinguishing system which is optimized for a double-deck tunnel. Consequently, the system considering low floor height and extended length as well as indoor hydrant for a wide range of use have been developed together with the performance verification and the process for commercialization before applying to the tunnel is underway now.

• Economic and Environmental Geology
• /
• v.54 no.2
• /
• pp.177-186
• /
• 2021

For disaster management and mitigation of earthquakes in Korea Peninsula, active fault investigation has been conducted for the past 5 years. In particular, investigation of sediment-covered active faults integrates geomorphological analysis on airborne LiDAR data, surface geological survey, and geophysical exploration, and unearths subsurface active faults by trench survey. However, the fault traces revealed by trench surveys are only available for investigation during a limited time and restored to the previous condition. Thus, the geological data describing the fault trench sites remain as the qualitative data in terms of research articles and reports. To extend the limitations due to temporal nature of geological studies, we utilized a terrestrial LiDAR to produce 3D point clouds for the fault trench sites and restored them in a digital space. The terrestrial LiDAR scanning was conducted at two trench sites located near the Yangsan Fault and acquired amplitude and reflectance from the surveyed area as well as color information by combining photogrammetry with the LiDAR system. The scanned data were merged to form the 3D point clouds having the average geometric error of 0.003 m, which exhibited the sufficient accuracy to restore the details of the surveyed trench sites. However, we found more post-processing on the scanned data would be necessary because the amplitudes and reflectances of the point clouds varied depending on the scan positions and the colors of the trench surfaces were captured differently depending on the light exposures available at the time. Such point clouds are pretty large in size and visualized through a limited set of softwares, which limits data sharing among researchers. As an alternative, we suggested Potree, an open-source web-based platform, to visualize the point clouds of the trench sites. In this study, as a result, we identified that terrestrial LiDAR data can be practical to increase reproducibility of geological field studies and easily accessible by researchers and students in Earth Sciences.

• Journal of Life Science
• /
• v.31 no.3
• /
• pp.287-297
• /
• 2021

Cornus officinalis Siebold & Zucc. is traditionally used as an edible and medicinal plant in many countries in East Asia. Previous studies have shown the pharmacological potential of extracts and components of C. officinalis, but comparative analysis of the composition of the leaf, stem, and fruit extracts has been insufficient to date. In the present study, the content of active antioxidant and anti-inflammatory ingredients was verified in different C. officinalis parts (under-ripe sansuyu, ripe sansuyu, seed, leaf, stem, and dried sansuyu). One active component, morroniside, was high in fruit (under-ripe and ripe sansuyu), while loganin was high in fruit (under-ripe sansuyu) and cornin was high in seeds. Total polyphenol contents were highest in fruit (ripe sansuyu) and flavonoids were highest in leaves. DPPH radical scavenging activity was highest in leaves, followed by seeds and then ripe sansuyu extract. The anti-inflammatory efficacy of leaf extracts of C. officinalis (LCO) was further investigated by measuring their effects on levels of nitric oxide (NO) and the pro-inflammatory cytokines interleukin (IL)-1β and IL-6 in RAW 264.7 macrophages. Non-cytotoxic concentrations of LCO effectively decreased the lipopolysaccharide (LPS)-induced expression of inducible NO synthase, resulting in decreased NO production. LCO also significantly suppressed LPS-induced production and expression of IL-1β and IL-6. Taken together, the present findings suggest that C. officinalis leaves have potential as natural materials for the development of antioxidant and anti-inflammatory agents.