• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2012.06a
• /
• pp.419-421
• /
• 2012

높이 2.5m의 콘크리트 플로팅 함체에 3층 규모의 상부골조가 있는 예제에 대해 동적 유체 해석과 정적 구조 해석을 수행하고 그 결과에 따라 종방향설계, 함체의 상부 및 하부 슬래브, 외벽 및 격벽에 대한 설계를 수행하였다. 환경 하중은 새만금 방파제 내부 정수역을 기준으로 파도주기 3.7초, 유의파고 1.0m와 풍속 40m/s를 적용하였으며, 하중조합은 ASCE/SEI 7-10을 기준으로 설계 하였다. 예제 구조물에 대한 설계 결과 고정하중에 의한 영향이 활하중 및 파랑하중에 비해 크게 나타났으며, 이로 인해 중앙부의 철근비가 높아지므로 고정하중을 감소시키는 방안을 검토하여야 함을 확인하였다. 또한 보의 지속하중에 의한 장기처짐과 추가적인 활하중에 의한 순간 처짐의 값이 허용 처짐값보다 크므로 보에서의 프리스트레싱을 고려해야 할 것으로 판단된다.

• Journal of Aerospace System Engineering
• /
• v.16 no.1
• /
• pp.97-103
• /
• 2022

An aircraft component can only be mounted on an aircraft if it has been certified to have a structural robustness under flight load conditions. Among the major components of the aircraft, a pylon is a structure that connects external equipment such as an engine, and external attachments with the main wing of an aircraft and transmits the loads acting on it to the main structure of the aircraft. In civil aircraft, when there is an incident of fire in the engine area, the pylon prevents the fire from spreading to the wings. This study presents the results of structural static tests performed to verify the structural robustness of a fuel pylon used to mount external fuel tank in an aircraft. In the main text, we present the test set-up diagram consisting of test fixture, hydraulic pressure unit, load control system, and data acquisition equipment used in the structure static test of the fuel pylon. In addition, we introduce the software that controls the load actuator, and provide a test profile for each test load condition. As a result of the structural static test, it was found that the load actuator was properly controlled within the allowable error range in each test, and the reliability of the numerical analysis was verified by comparing the numerical analysis results and the strain obtained from the structural test at the main positions of the test specimen. In conclusion, it was proved that the fuel pylon covered in this study has sufficient structural strength for the required load conditions through structural static tests.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.4 no.3
• /
• pp.1-10
• /
• 2000

우리 나라의 주거 건물의 많은 부분을 차지하는 조적조 건물은 저층이므로 내진 설계에 대한 지침이 마련되어 있지 않다. 그러나 조적조 건물의 경우 저층이라 하더라도 구조특성상 수평하중에 대한 저항능력이 매우 약하므로 내진 설계에 대한 기준이 요구된다. 일반적으로 내진설계 시 동적 해석을 수행하면 많은 시간이 소모되므로 실무자들에게 등가정적해석법을 제시하여 내진설계 시 편의를 제공하고 있다. 그러나 저층 조적조 건물은 일반적인 건물과는 거동 특성이 다르므로 저층 조적조 건물에 적용할 수 있는 해석법을 제시하고자 한다. 본 논문에서는 개구부의 비율에 따른 조적벽의 연성도, 강도 및 고유주기를 구하여 반응수정계수와 고유주기를 비교하여 우리 나라의 조적조 건물에 적합한 반응수정계수와 고유주기 산정식을 제안하였다.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.6 no.3 s.22
• /
• pp.29-35
• /
• 2006

Fiber element method in earthquake response analysis of bridges is used to represents a realistic flexural deformation according to nonlinear behavior of beam-column section. Nonlinear pseudo-static analysis of two column bent using fiber element is accomplished and failure mechanism of the plastic hinge region is studied. Load-displacement curve obtained by nonlinear pseudo-static analysis can be applicable to earthquake response analysis by capacity spectrum method. The nonlinear time history analysis of a full bridge model using fiber element experienced by the ground motion corresponding to the target response spectrum is accomplished. The result of time history analysis is similar to that of capacity spectrum method.

• Journal of the Korea Concrete Institute
• /
• v.23 no.5
• /
• pp.657-665
• /
• 2011

LB-DECK, a precast concrete panel type, is a permanent concrete deck form used as a formwork for cast-in-place concrete pouring at bridge construction site. LB-DECK consists of 60 mm thick concrete slab and 125 mm height Lattice-girders partly embedded in the concrete slab. These decks have been applied to the bridges, which girder spacings are short enough to resist longitudinal cracking caused by construction loads. This paper presents experimental research work conducted to evaluate the cracking load of LB-DECKs designed for long span bridge decks. Twenty four non-composite beams and four composite beams are fabricated considering three design variables of thickness of concrete slab, height of lattice-girder, and diameter of top-bar. Static loads controlled by displacements are applied to test beams to obtain cracking and ultimate loads. Vertical displacements at the center of beams, strains of top-bar, crack propagation in concrete slab, and final failure modes are carefully monitored. The obtained cracking loads are compared to the analytical results obtained by elastic analyses. Long-term analyses using age-adjusted effective modulus method (AEMM) are also conducted to investigate the effects of concrete shrinkage on the cracking loads. Based on the test results, the tensile strength and the design details of LB-DECKs are discussed to prevent longitudinal cracking of long span bridge decks.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.9 no.4
• /
• pp.9-14
• /
• 1989

A strain rate-dependent element model was used to study the loading rate-sensitivity of R/C beams and columns with different design factors. Conclusions were derived regarding the differences between the element axial/flexural performance under impulsive and quasi-static loads. Practical design formalas for predicting the loading rate-dependent axial and flexural strengths of R/C elements were also suggested.

• Journal of Korean Association for Spatial Structures
• /
• v.6 no.1 s.19
• /
• pp.83-90
• /
• 2006

The GF(Gust Factor) method is usually used as a method to evaluate equivalent static wind loads for general structures. The GF method is performed on the assumption that the shape of the equivalent static wind load profile is typically similar to that of mean wind loads. The shape of fluctuating wind loads could be quite different with that of the mean wind loads in case of large-span structures. So, the effect of higher modes as well as first mode must be considered to evaluate the wind loads. In this study, the ACS (Advanced Conditional Sampling) method is suggested to evaluate of equivalent static wind loads after investigating about GF and LRC method. The An method ran derive effective static wind loads by combining wind pressures and inertia forces of a structure chosen at a maximum load effect. The maximum load effect is assessed with the time history analysis using pressure data measured in wind tunnel tests. Equivalent static wind loads evaluated using ACS, GF, and LRC methods are compared to verify the effectiveness of ACS method.

• The tire
• /
• s.111
• /
• pp.20-29
• /
• 1984

유한요소법에 의하여 축대칭 정적하중을 받는 승용차용 래디알 타이어의 변형을 해석하였다. 요소는 8절점 parabolic-isoparametric 요소를 사용하였으며 타이어를 구성하는 cord-rubber복합체를 선형직교성을 갖는다고 가정하고, 그 복합체의 물성치를 간단한 식으로 표시하여 적용하였다. 공기압으로 인해 변형된 모양 및 cord에 작용하는 장력을 계산해 냈으며 이 변형된 모양을 plaster cast를 이용하여 측정한 실험치와 비교하였다. 또 타이어를 구성하는 구조가 달라지면 공기압으로 인하여 변형형태가 어떻게 변화하는가를 계산해 보았다. 이 결과로 belt의 cord수가 감소하거나 belt cord angle이 증가하면 타이어 외경이 증가함을 알 수 있다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.8 no.3
• /
• pp.264-273
• /
• 1984

초기경향이 있는 보강평판의 비선형 운동 방정식을 Galerkin method에 의하여 유도하였다. Runge Kutta method를 사용하여 step-load를 받고 있는 보강평판의 동적 좌굴문제의 수치해를 구하였다. 정적 좌굴실험에 의하여 좌굴하중을 결정함에 있어 동적 해석법을 응용할 수 있음을 입증하였으며, step-load를 받는 보강평판의 동적 좌굴해석으로 정적좌굴의 초기결함 민감성을 해 석하였다. 보강평판의 초기결함민강성은 평판보다 훨씬 낮으며 보강재의 편심비가 높을수록 민감 성은 둔화된다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.19 no.3 s.73
• /
• pp.303-312
• /
• 2006

This paper presents the equivalent nodal load for the element stiffness which represents the influence of the stiffness change such as the addition of elements, the deletion of elements, and/or the partial change of element stiffness. The reanalysis of structure using the equivalent load improves the efficiency very much because the inverse of the structural stiffness matrix, which needs a large amount of computation to calculate, is reused in the reanalysis. In this paper, the concept of the equivalent load for the element stiffness is described and some numerical examples are provided to verify it.