• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.3
• /
• pp.300-310
• /
• 1999

A constant-volume combustion chamber is developed to measure the burnt gas temperature over the wide ranges of equivalence ratio from 1.5 to 2.7 and pressure from 0.1 to 2.7 and pressure from 0.1 to 6 MPa by two-color method. The combustion temperature is also calculated by the conventional two-region model. The premixed fuel rich propane-oxygen-inert gas mixtures under high pressures are simultaneously ignited by eight spark plugs located on the circumference of combustion chamber with 45 degree intervals. The eight converging flames compress the end gases to high pressures. The transmissiv-ity in the chamber center during the final stage of combustion at the highest pressure is measured by in situ laser extinction method. Comparisons are made with the combustion temperatures between two-color method and two-region model. It is found that the burnt gas temperature mea-sured by two-color method is higher than that calculated by two-region model because of being the negative temperature gradient on the calculation and the temperature distribution of light path-length on the measurement and the burnt gas temperature for the turbulent combustion is higher than that of the laminar combustion under the same conditions because the heat loss for turbulent combustion is lower due to the shorter combustion period.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.2
• /
• pp.135-146
• /
• 2015

This paper is the fourth on the combustion characteristics of the landfill gas in a constant volume combustion chamber for a large displacement volume commercial engine and the second dealing with torch ignition. It discusses the combustion characteristics of torch ignition on the basis of the heat release and visualization. The results show that the jet and/or spout from the torch promote combustion by accelerating the flame front in the main combustion chamber. In addition, a hot gas jet exists when the orifice diameter is 4 mm, whereas the flame passes directly through the orifice if the diameter is 6 mm or greater. In addition, the effect of torch ignition differs according to the combination of the methane fraction, torch volume, and orifice size because various combustion processes occur as a result of the interaction of these parameters. Finally, it was found that the most suitable torch should have an orifice diameter of not less than 6 mm and an area ratio of not more than 0.15 to secure a consistent combustion process in a real engine.

• Journal of the Korean Society of Visualization
• /
• v.9 no.1
• /
• pp.42-48
• /
• 2011

Six different size of torch-ignition device were applied in a constant volume combustion chamber for evaluating the effects of torch-ignition on combustion. The torch-ignition device was designed for six different volumes and same orifice size. The combustion pressures were measured to calculate the mass burn fraction and combustion enhancement rate. In addition, the flame propagations were visualized by shadowgraph method for the qualitative comparison. The result showed that the combustion pressure and mass burn fraction were increased when using the torch ignition device. And the combustion duration were decreased. The combustion enhancement rates of torch-ignition cases were improved in comparison with conventional spark ignition. Finally, the visualization results showed that the torch-ignition induced faster burn than conventional spark ignition due to the earlier transition to turbulent flame and larger flame surface, during the initial stage. Finally, the initial flame propagation was affected by torch-ignition volume.

• Journal of the Korean Society of Visualization
• /
• v.8 no.1
• /
• pp.19-24
• /
• 2010

Five different size of orifice were applied in a constant volume combustion chamber for evaluating the effects of torch-ignition on combustion. The initial flame development and flame propagation were analyzed by the mass burned fraction and combustion enhancement rate. The combustion pressures were measured to calculate the mass burned fractions and the combustion enhancement rates. In addition, the flame propagations were visualized by the shadowgraph method for the qualitative comparison. The result showed that the combustion pressure and mass burned fraction were increased when using the torch-ignition device. The combustion enhancement rates of torch-ignition cases were improved in comparison with conventional spark ignition. Finally, the visualization results showed that the torch-ignition induced faster burn than conventional spark ignition due to the earlier transition to turbulent flame and larger flame surface, during the initial stage.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.10
• /
• pp.858-869
• /
• 2014

Most of the aerospace propulsion is based on the Brayton cycle, in which the combustion is held through the constant pressure process, but further improvement of performance by increasing compression ratio is challenged by mechanical limits. Detonation propulsions, regarded promising for high-speed propulsion for a lase decade, is more rigorously studied in these days as a game-changer for the improvement of thermodynamic efficiency of propulsion and power generation systems. Since, the additional compression by the strong shock of the detonation wave is considered increasing thermodynamics efficiency that is hardly achievable by the conventional compression systems. Present paper will give an introduction the latest technical trends on the Pulse Detonation Engines(PDEs) and the activities on the Pressure Gain Combustion (PGC) based on Constant Volume Combustion (CVC).

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.913-914
• /
• 2017

Structural analyses of a engine system is required in development stage for increasing structural reliability and reducing weight. Attitude of a launch vehicle during flight is controlled by combustion chamber rotation varying with TVC (thrust vector control) actuator displacements. In this study nonlinear static analysis is performed for a 75 tonf-class liquid rocket engine using before and after the TVC actuation.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.04a
• /
• pp.13-13
• /
• 2000

일반적으로 고체추진 로켓 모타의 개발단계 때 공통적으로 수행되는 주시험(main test)으로는 추력, 압력, 회전률 등의 성능측정을 하기 위한 정적연소시험(static firing test), 내부 정수압(hydrostatic pressure)에 의한 폭발 압력 시험, 연소중이나 연소 후 케이스에 대한 굽힘 강성 시험, 이외에 노화 시험, 환경시험 등이 요구된다. 그러나 신궁과 같은 휴대용 대공 시스템의 추진기관 개발의 경우에는 사수를 보호하기 위해 여러 가지 안전장치들이 설계되고, 이러한 장치들의 성능에 대한 요구 조건들을 확인하기 위한 특수시험(specific test)들이 필요하게 된다. 이러한 특수시험을 위한 각종 시험대들을, 위에서 언급한 주시험을 위해 사용되는 정적시험대(static test bench)들과 구분하기 위해 동적 시험대(DTB : Dynamic Test Bench)라고 한다. 본 연구에서는 신궁 추진기관의 사출모타 점화에서 비행모타 점화에 이르는 일련의 비행절차를 확인하기 위한 동적 시험대 설계 및 제작, 계측장치 구성 및 데이터 획득 방법 등에 관한 내용을 소개하며, 동적 시험대에서 수회에 걸쳐 수행된 동적 시험 결과를 분석/정리하였다.

• Journal of the Korean Society of Combustion
• /
• v.17 no.2
• /
• pp.1-8
• /
• 2012

Laminar flame speeds of Methane at elevated temperatures and pressures were investigated using constant volume spherical chamber. Pressure trace during combustion was measured in each test and this was used in calculating laminar flame speed of Methane. To have large amount of data, experimental apparatus was fabricated with fully automatically controlled feature. A calculating code which calculates laminar flame speeds at various temperatures and pressures with one experimental result was used to calculate laminar flame speeds. The experimental and calculating methods were verified using the calculated laminar flame speed result with PREMIX code.

• Journal of ILASS-Korea
• /
• v.15 no.3
• /
• pp.150-156
• /
• 2010

Ethanol has properties of a lower setting point, higher oxygen contents, lower cetane numbers, and also higher volatility compared to biodiesel. Thus, biodiesel fuel can be improved in the fluidity of blending fuel and exhaust emissions by blended ethanol fuel. This research aims to understand combustion characteristics of biodiesel-ethanol blending fuel inside a constant volume chamber. High speed camera was applied to visualize the physics of development of combustion processes, and combustion pressure and exhaust emissions were measured at several blending ratios of ethanol and biodiesel fuel. This information may contribute to improve the performance of biodiesel engine and reduce emissions in future.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.2
• /
• pp.136-145
• /
• 1995

The aim of this study is to gain a better understanding of the effect of a flow motion on the flame development by means of an optically-accessible constant-volume combustion chamber and the visualization technique of a combustion flame. At first, the characteristics of a flame propagation are investigated in the combustion field of the two kinds of flow conditions such as a quiescent and a flowing condition, and methane-air mixture is used as fuel. Then the same investigation is performed in two flow configurations : bulk flow motion type and turbulence generating type. In this study, the combustion phenomena are analyzed by measuring the combustion pressure, flame propagation speed, mean velocity, turbulent intensity, and mass fraction burned.