• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.8 no.2
• /
• pp.135-145
• /
• 1988

This study deals with the prediction of crack propagation in concrete mortar subjected to static and dynamic load. Total 54 CLWL-DCB(Crack-line-loaded-double-cantilever beam) concrete mortar specimens were tested to measure crack growth using ASTM 561-80. Main variables were sand to cement ratio and water to cement ratio. The resulting load(P)-COD(Crack Opening Displacement; $2V_1$) curves and COD-CTOD (Crack Tip Opening Displacement; $2V_2$) curves were analyzed to calculate effective crack length and physical crack length by way of ASTM 561-80 proposed. Replica crack length were also obtained directly during the test. The differences in crack propagation between under static load and under dynamic load were investigated.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.1
• /
• pp.48-58
• /
• 2014

In this study, quasi-static according to the displacement-controlled (strain control) method tests on RC columns for seismic reinforcement performance in accordance with the provisions of the seismic design and construction before 1992 design code for highway bridges in korea. Used reinforcement that improves the performance of Inorganic Helical Bar, a kind of alloy steel, circular columns were tested outside the seismic reinforcing. In the experiment, fracture behavior, lateral load-displacement relation, ductility and energy assessment evaluation was performed through tests. The variables in experimental are section force of reinforcement, spiral reinforcement spacing, reinforcement method. Improved seismic performance and effect were confirmed through quasi-static test experiments. The results of study confirmed determination the appropriate size of reinforcement, reinforcement forces, spacing and selection of the type required, furthermore, not only mechanical reinforcement but also substitution of high-strength concrete reinforced with concrete cover improved seismic performance.

• Geotechnical Engineering
• /
• v.6 no.3
• /
• pp.13-30
• /
• 1990

In this paper, response of pile foundations under seismic loading is studied for use in aseismic design of deep foundations. Both the pseudostatic methods such as subgrade reaction theory by Reese, and elastic analysis by Poulos, and the dynamic methods proposed by, respectively, Prakash and Gazetas, are used for this study. The top displacements and maximum bending moments of example piles are obtained by each method mentioned above, and the results by each method are compared among others. The group pile effects are also considered approximately. The calculated results are compared with experimental results obtained by Novak in 1984. The pseudostatic methods, combined with dynamic group interaction factors, and the dynamic method proposed by Gazetas which considers both kinematic interaction and inertial interaction, separately, estimate the top displacements reasonably well : the method by Prakah or the pseudostatic methods combined with static group interaction factors may overestimate the top displacements and bending moments as well. Therefore, it is recommended to the the simple elastic analysis combined with dynamic group interaction factors for aseismic design of pile foundatins and to confirm the results by the Gaz etas' dynamic methods.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.10a
• /
• pp.131-136
• /
• 2003

Five expensive sensors are necessary to control a magnetic bearing system. The sensor price rate of magnetic bearing system is high. So it is necessary that cheap and good sensor is developed. The optical fiber displacement sensor is adaptive to satisfy this condition. We can design magnetically suspended spindle based on static characteristic of optical fiber displacement sensor developed. The controller can be designed by decoupled feedback PD. Therefore, it is simpler than any other controller comparatively.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2011.06a
• /
• pp.192-194
• /
• 2011

육상의 자원고갈로 인한 해양자원의 관심 증가로 플랜트 사업의 수요가 증가함에 따라 플로팅 구조물의 안전성 확보를 위한 구조해석이 필요하다. 이 연구에서는 범용 유한요소 프로그램인 ABAQUS를 사용하여 3차원 플로팅 구조물의 상부구조물에 정적하중과 진폭의 크기가 다른 파랑하중을 적용하여 모멘트 및 변위를 비교한다.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1992.04a
• /
• pp.89-94
• /
• 1992

구조물의 비탄성 지진응답을 예측하기 위하여 수행되는 진동대 실험(Shaking Table Test)과 준정적 실험(Quasic-Static Test)의 각 장점을 조합한 유사동적 실험(Pseudodynamic Test)은 실물 크기 구조물의 비탄성 거동온 파악하는 데 널리 사용되고 있다. 이러한 유사동적 실험에서는 구조물에 변위이력의 정확한 가력 및 측정이 가장 중요하다. 측정된 변위와 계산된 변위의 차를 조절오차(Control Error)라고 하며, 임의의 단계에서 측정된 변위를 조정하므로서 그 다음 단계의 조절오차 및 측정오차(Measurement Error)를 감소시킬 수 있다. 따라서 개선된 유사동적 실험의 알고리즘을 얻을 수 있다.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.4
• /
• pp.211-221
• /
• 2003

The response displacement method is the most frequently used method for seismic design of underground structures. This method is pseudo-static method, and the evaluations of velocity response spectrum of seismic base and response displacement of surrounding soil are the most important steps. In this study, the evaluation of velocity response spectrum of seismic base according to the Korean seismic design guide and the simple method of calculating the response displacement were studied. It was found that velocity response spectrum of seismic base can be estimated by directly integrating the ground-surface acceleration response spectrum of soil type S$_A$, and the evaluation of the response displacement using double cosine method assuming two layers of soil profile shows the advantages in the seismic design.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.5
• /
• pp.376-385
• /
• 2017

In this paper, a method for the estimation of structural displacements using structure's mode shapes and accelerations is suggested to reduce the disadvantages of acceleration time integration method. Acceleration time integration method requires accurate information on initial conditions, and errors caused by noise can be accumulated during time integration. To avoid these problems, the method for the estimation of structural displacements based on mode superposition method is developed and two vibration experiments for cantilever beam are conducted to verify this method. Static displacements and dynamic displacements of beam structure are estimated using measured accelerations from experiments and mode shapes of cantilever beam, and they are compared with measured displacements using laser displacement sensor. From these results, the validity and usefulness of this method are verified.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.4
• /
• pp.53-60
• /
• 2019

In this study, a method for updating the finite element model of bridges with genetic algorithm using static displacement were presented, and verified this method using field test data for PSC girder bridge. As a field test, static load test and pseudo-static load test were conducted, and updated the finite element model of test bridge using each test data. Finally, evaluated the bridge load carrying capacity with updated model using pseudo-static load test's displacement data. To evaluate the bridge load carrying capacity, KHBDC-LSD, KHBDC and AASHTO LRFD's live load model were used, and compared the each results.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.6
• /
• pp.153-160
• /
• 2002

A new system identification method based on tunnel deformation data is proposed to find the damage in the lining structure. For this, an inverse problem in which the deformation data and dead load of concrete lining are known a priori is introduced to estimate the degree and location of the damages. Models based on uniform reduction of stiffness and homogenized crack concept are individually employed to compare the applicability and relative advantages of the models. Numerical analyses are peformed for the idealized tunnel structure and the effect of white noise, common in most measurement data, is also included to better understand the suitability of the proposed models. As a result, model 1 based on uniform stiffness reduction method is shown to be relatively insensitive to the noise, while model 2 with the homogenized crack concept is proven to be easily applied to the field situation since the effect of stiffness reduction is rather small.