• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.4
• /
• pp.13-25
• /
• 1994

In order to design and improve a new machine tool, there is a need for a better understanding of the cutting force. In this paper, the computer programs were developed to predict not only the mean specific cutting pressure but also the cutting force. The simulated cutting forces in X, Y, Z directions resulted form the developed cutting force model were compared with the measured cutting forces in the time and frequency domains. The simulated cutting forces resulted from the new cutting force model have a good agreement with the measured force in comparison with these resulted from the existing cutting force model.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.5
• /
• pp.46-54
• /
• 2004

A cutting force model predicting the dynamic force induced by the axial vibration of it plate in face milling is introduced. When a plate face is milled, deformation in tool axial direction is considerable. Therefore, cutting forces are affected by not only inner-outer modulation in feed direction but also by axial deformation. A PTP (peak-to-peak) diagram made by the simulated dynamic force model is evaluated. The stability of the face milling process such as the chatter outset, and the stable cutting region can be simply estimated. Simulation results are compared with that of experiment.

• Journal of the Korean Society for Precision Engineering
• /
• v.8 no.1
• /
• pp.116-129
• /
• 1991

A cutting force model for face milling operation using 3-directional specific cutting force coefficients is developed. The model is taken into consideration factors such as cutter geometry, machining conditions, spindle eccentricity, insert initial postion errors, etc. The simulated force in X, Y, Z directions from the model are subsequently compared with measured forces in the time and frequency domains. The simulated forces have a good agreement with measured forces.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.9
• /
• pp.4149-4155
• /
• 2013

High speed machining for higher cutting speed and feedrate lead to a increase of surface quality and material removal rate. This paper presents a study of the influence of cutting conditions on the vibration characteristics obtained by machining with face milling cutter for high speed machining. In this paper, Taguchi experimental design method which is based on orthogonal array table was applied to study vibration characteristics with high speed face milling cutter. The experimental conditions used orthogonal array of $L_{27}(3^{13})$. In this work, design and analysis of experiments is conducted to study the effects of these parameters on the vibration by using the S/N ratio, analysis of variance. Four cutting parameters namely, feed rate, champer length, cutting speed, and depth of cut were optimized with consideration of vibration characteristics.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.20-25
• /
• 1994

절삭공정의 자동화의 무인화를 달성하기 위해서는 경험을 가진 작업자의 역활이 컴퓨터에 의한 자동적인 감시 및 제어시스템으로 대체되어야 한다. 특히 공작기계에서 발생할 수 있는 자체의 고장이나 절삭과정중에 발생하는 이상상태를 실시간으로 검출하여 원인을 자동적으로 진달 할 수 있어야 한다. 절삭가공 공작기계의 이상상태 감시 및 진단의 현황을 살펴보면 주로 공구상태의 감시와 채터 감시가 연구의 대상 이 되고 있다. 공구상태의 감시는 공구의 마모와 파단을 검출하고 있다. 이 중에서 공구의 파단은 발생 즉시 실시간으로 감시되어야 한다. 밀링작업에서는 1회전 이내의 공구회전에 파단을 검출하고 기계를 정지시켜야 한다. 최근의 절삭가공에서는 절삭공구로 강력절삭을 위해 고경도 재료를 사용함에 따라 공구의 파단이 빈번하게 발생하고 있다. 정면밀링과 같은 단속절상에서는 절삭날이 큰 충격을 받으므로 더욱 파단에 대한 감시가 필요하다.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.4
• /
• pp.91-98
• /
• 2000

In this paper , presented is a method of on-line estimation of the radial immersion ratio and cutting force ratio using cutting force. When a tooth finishes sweeping, sudden drop of cutting forces occurs. These force drops are equal to the cutting forces that act on a single tooth at the swept angle of cut and can be obtained from cutting force signals in feed and crossfeed directions. The ratio of cutting forces in feed and cross-feed directions acting on the single tooth at the swept angle of cut is a function of the swept angle of cut and the ratio of radial to tangential cutting force. In the research, it is found that the ratio of radial to tangential cutting force is not affected by cutting conditions and axial rake angle. Therefore, the ratio of radial to tangential cutting force determined by just one preliminary experiment can be used regardless of the cutting conditions. Using the measured cutting forces, the radial immersion ratio is estimated along with the cutting force ratio at that immersion angle. Various experiments show that the radial immersion ratio and instantaneous ratio of the radial to tangential direction cutting force can be estimated by the proposed method very well.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.8
• /
• pp.178-185
• /
• 1999

In tool condition monitoring systems, parameters should be set to a certain threshold. In many cases, however, the threshold is dependent on cutting conditions, especially the radial immersion ratio. In this presented is a method of on-line estimation of the radial immersion ratio in face milling. When a tooth finishes sweeping, a sudden drop of cutting force occurs. The force drop is equal to the cutting force that acting on a tooth at the swept angle of cut and can be acquired from cutting force signals in feed and cross-feed directions. Average cutting force per tooth period can also be calculated from cutting force signals in two directions. The ratio to cutting forces in two directions acting on a tooth at a certain swept angle of cut and the ratio of average cutting forces in two directions per tooth period are functions of the swept angle of cut and the ratio of radial to tangential cutting forces. Using these parameters, the radial immersion ratio is estimated. Various experiments are performed to verify the proposed method. The results show that the radial immersion ratio can be estimated by this method regardless of other cutting conditions.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.6
• /
• pp.972-979
• /
• 2001

Tool fracture index(TFI) was developed in order not only to detect tool fracture but also to predict the amount of tool fracture in face milling. TFI is calculated by using peak-to-valley values of cutting force acting on teeth and their ratio between the adjacent teeth. When the tool fractures, a large value of TFI proportional to the amount of tool fracture was obtained periodically and decreased gradually. It was found that TFI is independent of cutter runout and it almost does not vary during transient cutting such as cutting condition change during machining. The threshold of tool fracture can be analytically determined by TFI developed in this paper, because the magnitude of TFI was shown to be dependent on the ratio of the amount of tool fracture to feed per tooth and immersion ratio. It was possible to predict the amount of tool fracture in experiments by using the proposed TFI.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.4
• /
• pp.19-27
• /
• 1995

Face milling is required to study cutting process with a view of multipoint cutter. This experimental study mainly deals with the single and multi-insert cutting characteristics using coated tool. Because metal cutting of the single and multi-insert has a large relation to the improvement of productivity, the economic cutting process can be achieved by the analysis of proper metal cutting mechanism. Therefore, machining characteristics of face molling in this paper has been studied by investigating the role of different insert number which is concerned with mean cutting force, the RMS values of AE(acoustic emission) signal, tool life and surface roughness in milling SS 41 and SUS 304. The cutting force and AE signal are monitored to make an analysis of cutting process. The surface roughness of the specimens machined by inserts of different numbers is measured at different speeds, feeds and depth of cut. The width of flank wear is also observed.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.8
• /
• pp.39-52
• /
• 1995

In order to design and improve a new machine tool, there is a need for a better understanding of the dynamic cutting force. In this paper, the computer programs were developed to predict the dynamic cutting force by the mean specific cutting pressure in the face milling process. The simulated cutiing forces in X, Y, Z directions resulted from the developed dynamic cutting force model are compared with the measured cutiing forces in the time and frequency domains. The simulated cutting force model have a good agreement with the measured forces in comparison with those resulted from the existing cutting force model.