• Journal of Energy Engineering
• /
• v.25 no.2
• /
• pp.94-100
• /
• 2016

ESS(Energy Storage System) is an important source that keeps power supply stable and utilizes electricity efficiently. For example, ESS contributes to resolve power supply imbalance, stabilize new renewable energy output and regulate frequency. ESS is predicted to be expanded to 55.9GWh of installed capacity by 2023, which is 30 times more than that of 2014. To raise competitiveness of domestic ESS industry in this increasing world market, we have disseminated load-shift ESS for continuous power supply imbalance with FR ESS, and also necessity to secure domestic track record is required. However in case of FR ESS, utility of installing thermal power plant is generally generated within 5% range of rated capacity, so that scalability of domestic market is low without dramatic increase of thermal power plant. Necessity of load-shift ESS dissemination is also decreasing effected by surplus backup power securement policy, raising demand for new dissemination model. New dissemination model is promising for $CO_2$ reduction effect in spite of intermittent output. By stabilizing new renewable energy output in connection with new renewable energy, and regulating system input timing of new renewable energy generation rate, it is prospected model for 'post-2020' regime and energy industry. This research presents a policy alternatives of REC multiplier calculation method to induce investment after outlining PV-connected ESS charge/discharge mode to reduce GHG emission, This alternative is projected to utilize GHG emission reduction methodology for 'Post-2020' regime, big issue of new energy policy.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1996.10a
• /
• pp.319-323
• /
• 1996

\ulcorner\ulcorner\ulcorner\ulcorner 80,000 rpm \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner(ultra-centrifuge)\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner. \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner(critical speed)\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner(separation margin)\ulcorner \ulcorner\ulcorner, \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner \ulcorner\ulcorner-\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner \ulcorner\ulcorner\ulcorner. \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner \ulcorner \ulcorner\ulcorner\ulcorner, \ulcorner\ulcorner \ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner(extra slender shaft)\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner. \ulcorner\ulcorner \ulcorner\ulcorner\ulcorner, \ulcorner\ulcorner 1\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner \ulcorner\ulcorner\ulcorner(bumper ring) \ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner(guide bearing)\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner. \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner(finite element method)\ulcorner \ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner, \ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner(damping)\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner.

• The Journal of Korean Institute of Information Technology
• /
• v.15 no.12
• /
• pp.181-188
• /
• 2017

As a population of leisure activities grows and diversifies, there is a great demand for portable and environment-friendly power generation systems. A small wind power generation system is emerging as a suitable power generation equipment to meet these needs. The most important thing when developing a small portable wind turbine is to reduce the weight of the generator and increase the efficiency. The existing 300W wind turbine generator weighs about 10kg, which is heavy to carry. Therefore, a new generator weighing less than 4kg to make it easy to carry with high efficiency has been developed. In addition, considering complicated characteristics of wind volume and topography of Korea, a small wind turbine that can be used in urban and rural areas individually was constructed. Through basic designing and optimization, the lightweight and efficient generator was manufactured. It is a 300W wind turbine designed and fabricated with reduced weight as a prototype. The average output voltage of the generator was 24.7V at 900rpm no-load test. On a load test with the average line voltage 36.8V and the average phase current 2.62A, when the mechanical input was 339.84W, an average voltage output of the generator was measured as 289.5W with efficiency of 85.18%. The generator weight was 3.84kg.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.4
• /
• pp.587-593
• /
• 2021

Since 2017, a total of 29 fire accidents have occurred in energy storage systems (ESSs) as of June 2020. The common mode voltage (CMV) is one of the electrical hazards that is assumed to be a cause of those fire accidents. Several cases of CMV that violate the allowable insulation level of a battery section are being reported in actual ESS operation sites with △-Y winding connections. Thus, this paper evaluates the characteristics of CMV. An ESS site was modeled with an AC grid, PCS, and battery sections using PSCAD/EMTDC software. As a result of a simulation based on the proposed model, it was confirmed that characteristics of CMV vary significantly and are similar to actual measurements, depending on the grounding method of the internal transformer for PCS. The insulation level of the battery section may be severely degraded as the value of CMV exceeds the rated voltage in case of a grounding connection. It was found that the value of CMV dramatically declines when the internal transformer for PCS is operated as non-grounding connection, so it meets the standard insulation level.

• Applied Chemistry for Engineering
• /
• v.30 no.1
• /
• pp.62-67
• /
• 2019

This study was focused on the design and the performance analysis of integral Hot BoP for recovering waste heat from high-temperature exhaust gas in 2 kW class solid oxide fuel cell (SOFC). The hot BoP system was consisted of a catalytic combustor, air preheater and steam generator for burning the stack exhaust gas and for recovering waste heat. In the design of the system, the maximum possible heat transfer was calculated to analyze the heat distribution processes. The detail design of the air preheater and steam generator was carried out by solving the heat transfer equation. The hot BoP was fabricated as a single unit to reduce the heat loss. The simulated stack exhaust gas which considered SOFC operation was used to the performance test. In the hot BoP performance test, the heat transfer rate and system efficiency were measured under various heat loads. The combustibility with the equivalent ratio was analyzed by measuring CO emission of the exhaust gas. As a result, the thermal efficiency of the hot BoP was about 60% based on the standard heat load of 2 kW SOFC. CO emission of the exhaust gas rapidly decreased at an equivalent ratio of 0.25 or more.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.4
• /
• pp.456-465
• /
• 2019

PHEV(Plug in Hybrid Electric Vehicle) and BEV(Battery Electric Vehicle) equip high voltage batteries to drive motor and vehicle electric system. Those vehicle require OBC(On-Board Charger) for charging batteries and LDC(Low DC/DC Converter) for converting from high voltage to low voltage. Since the charger and the converter actually separate each other in electrical vehicles, there is a margin to reduce the vehicle weight and area of installation by integration two systems. This paper studies a 1.5kW LDC converter that can be integrated into an OBC using an isolated current-fed converter by simplifying the design of LDC transformers. The proposed LDC can control the final output voltage of the LDC by using a fixed arbitrary output voltage of the bidirectional buck-boost converter, so that Compared to the existing OBC-LDC integrated system, it has the advantage of simplifying the transformer design considering the battery voltage range, converter duty ratio and OBC output turn ratio. Prototype of the proposed LDC was made to confirm normal operation at 200V ~ 400V input voltage and maximum efficiency of 91.885% was achieved at rated load condition. In addition, the OBC-LDC integrated system achieved a volume of about 6.51L and reduced the space by 15.6% compared to the existing independent system.

• Plant Journal
• /
• v.14 no.4
• /
• pp.39-47
• /
• 2018

In this research, when the output of the standard coal-fired thermal power plant operating continuously at the rated output of 500 MW is changed to operate at 300 to 500 MW, the amount of sulfur oxide produced and the amount of sulfur oxide in the absorption tower of desulfurization equipment and proposed an extra liquid to gas ratio improvement inversely proportional to the output. In order to calibrate the combustion efficiency at low power, the ratio of sulfur oxides relative to the amount of combustion gas is increased as the excess air ratio is increased. When the concentration of sulfur oxide at the inlet of the desulfurization absorber was changed from 300 to 500 ppm along with the output fluctuation. The liquid to gas ratio of limestone slurry and combustion gas was changed from 10.99 to 16.27. Therefore, if the concentration of sulfur oxides with output of 300 MW is x, The following correlation equation is recommended for the minimum required flow rate of slurry for the reduction of surplus energy due to the increase of the liquid weight at low load. $y1[m^3/sec]=0.11x+3.74$

• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.3
• /
• pp.485-492
• /
• 2021

The wind turbines with a rated capacity of 50kW or less are generally considered as small class. Small wind turbines are an attractive alternative for off-grid power system and electric home appliances, both as stand-alone application and in combination with other energy technologies such as energy storage system, photovoltaic, small hydro or diesel engines. The research objective is to develop the 50kW scale wind turbine blades in ways that resemble as closely as possible with the construction and methods of utility scale turbine blade manufacturing. The mold process based on wooden form is employed to create a hollow, multi-piece, lightweight design using carbon fiber and fiberglass with an epoxy based resin. A hand layup prototyping method is developed using high density foam molds that allows short cycle time between design iterations of aerodynamic platforms. A production process of five blades is manufactured and key components of the blade are tested by IEC 61400-23 to verify the appropriateness of the design. Also, wind system with developed blades is tested by IEC 61400-12 to verify the performance characteristics. The results of blade and turbine system test showed the available design conditions for commercial operation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.2
• /
• pp.593-601
• /
• 2021

The axial fan is an element of a blower used for ventilation in various industrial fields. Many studies on aerodynamic performance have been conducted to assess axial fans using fluid dynamics. The subject was a large axial fan size, 1800 mm in diameter with 100 horsepower. The blower's axial fan consisted of blades, hubs, hub caps, and bosses are important components. The blade design has a great influence on the aerodynamic performance. 3D point data is extracted using an aerodynamic performance prediction program, and a 3D modeling shape is generated. The blades and hubs, which are important components, can be easily modified if processed by cutting owing to the environment in which blades and hubs are manufactured through die casting or gravity casting. In this study, the structural safety of components and the analysis results of weak areas at the rated operating speed of the axial fan were verified using the maximum stress and safety factor. The tip clearance reflected in the design was the rotation of the blade. To check whether there is interference with other components, the displacement result was derived to verify the structural safety of the axial fan.

• Journal of the Society of Disaster Information
• /
• v.18 no.3
• /
• pp.646-659
• /
• 2022

Purpose: In this study, we developed a 4-way sway prevention brace that efficiently reduces the installation area and has excellent stability and seismic performance compared to the conventionl sway prevention brace used in existing firefighting facilities. The performance and reliability of the developed 4-way way prevention brace were analyzed by the tensile, compression tests and seismic tests. Method: As the static test, 4-way sway prevention braces were installed on the horizontal and vertical pipes to perform the tensile and compression tests based on the KFI certification standard and the maximum movement was measured at the rated load. As a dynamic test, 4-way sway prevention braces were installed in the pipes filled with water, and the test response spectrum to the input excitation wave were measured through the acceleration sensors. After the seismic tests, separation, failure, and local deformation of the pipes, and 4-way sway prevention braces were not observed. Result: The results of the tensile and compression tests indicated that the maximum movement of the pipe during tension and compression was 50% to 70% or less compared to the certification values, indicating that the performances of the 4-way sway prevention braces were very excellent. The results of the the seismic tests indicated that the test response spectrum of the 4-way sway prevention braces is within the required response spectrum. Conclusion: In this study, it was found that the 4-way sway prevention braces satisfied the KFI certification standard and were superior compared to the existing sway prevention brace in terms of the stability, cost, and installation area.