• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.656-659
• /
• 2009

직접메탄올형 연료전지(Direct Methanol Fuel Cell)는 휴대용으로 사용할 수 있는 소형 전원용으로 주로 개발되고 있으며, 다양한 용도로 사용이 가능하다. 하지만 직접메탄올연료전지에서 전해질로 많이 쓰이는 Nafion막은 이를 통한 메탄올 크로스오버(Crossover) 때문에 연료전지의 성능을 제한시키고 있다. 본 연구에서는 Nafion 117를 사용하여 전극 면적 100cm2 의 DFMC용 MEA를 제작하고, 공기 유량을 3ml/mim으로 고정하고, 메탄올 유량을 2,3 ml/min로 각각 공기극와 연료극에 공급하여 온도변화(50, 60, 70, $80^{\circ}C$)에 따른 성능을 확인하였다. DMFC의 적당 반응 온도는 $70^{\circ}C$로 생각되고, 유량은 메탄올 2ml/min, 공기 3ml/min유량 공급시가 성능이 높게 나오는 결과를 얻으나 일정시간 지나면 성능이 메탄올 3ml/min, 공기 3ml/min유량 공급시 보다 성능이 떨어지는 현상이 일어나기 때문에 $70^{\circ}C$ 반응온도에 메탄올 3ml/min, 공기 3ml/min의 유량 공급이 본 논문에서 최적화된 성능을 내는 조건으로 사료된다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.117-118
• /
• 2011

초경합금 위에 RF Magnetron Sputter를 이용하여 Ti 중간층을 증착 후 MPECVD(Microwave Plasma Enhanced Chemical Vapor Deposition) 시스템을 이용하여 나노결정 다이아몬드 박막을 증착 하였다. 공정압력, 마이크로웨이브 전력, Ar/$CH_4$ 조성비, 기판온도를 일정하게 놓고 직류 bias의 인가 여부를 변수로 하고 증착시간을 0.5, 1, 2시간으로 변화시켜 박막을 제작하였다. 제작된 시편은 FE-SEM과 AFM을 이용하여 다이아몬드 박막의 표면과 다이아몬드 박막의 표면 거칠기 등을 측정하였고, Raman spectroscopy와 XRD를 이용하여 다이아몬드 결정성을 확인하였다. Automatic Scratch �岵謙�ter를 이용하여 복합박막의 층별 접합력을 측정하였다. 바이어스를 인가하지 않고 다이아몬드 박막을 증착할 경우 증착 시간이 증가할수록 다이아몬드 입자의 평균 크기가 증가하며 입자들이 차지하는 면적이 증가하는 것을 확인하였다. 그러나 1시간이 경과해도 아직 완전한 박막은 형성되지 못하고 2시간 이상 증착 시 완전한 박막을 이루는 것이 확인되었다. 이에 비해서 바이어스 전압을 인가할 경우 1시간 내에 완전한 박막을 이루었다. 표면 거칠기는 바이어스를 인가한 경우가 그렇지 않은 경우에 비해서 조금 높은 것으로 나타났다. 이러한 바이어스 효과는 표면에서의 핵생성 밀도 증가와 재핵생성 속도 증가에 기인하는 것으로 해석된다.

• Journal of Conservation Science
• /
• v.26 no.1
• /
• pp.61-67
• /
• 2010

After selecting five types of adhesive epoxy resin for metallic cultural assets such as $Araldite^{(R)}$ rapid type, $Devcon^{(R)}$, $Araldite^{(R)}$ SV427+HV427, $CDK^{(R)}$520, $Araldite^{(R)}$ AW106+HV953 which had already been studied, this paper approached more closely the problem of yellowing and the signal of aging with time passing by connecting the problems with the safety of metallic cultural assets. The change of physical properties according to the change of state of epoxy adhesives was investigated through the change of flexural strength and the change of surface hardness by artificially providing the possible environmental change factors such as ultra-violet ray, and acid base, and how the epoxy chemically changes in its ingredients by the environment was analyzed through FT-IR. As a result of the experiment, for the most part of adhesives brought about the physical change of flexural strength, the change of surface hardness, and the chemical change of chemical ingredients as the product of alcohol, which were respectively different according to the time of ultraviolet irradiation, and acid base change. Under most of the conditions, SV427+HV427 and $CDK^{(R)}$520 were fairly stabilized under each condition of weatherability, but it seems that they should be refrained from being applied in case that the area to restore is thin and wide because the degree of flexural strength of themselves is low. Also, it is found that the preservation environment is very important not only for artifacts but also for the preservation of resins sused for preservation treatment.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.13 no.2
• /
• pp.129-136
• /
• 1991

The fibrin sealant was first designed as an alternative to surgical suture for the purpose of surface-to-surface union especially in parenchymal organs like the liver, spleen and kidney. The clinical application of currently used fibrin sealant was first introduced in 1972. The fibrin sealant consists of principal two components; lyophilized human fibrinogen and bovine thrombin. The fibrinogen component also contains coagulation factor XIII. A solution of aprotinin, an inhibitor of fibrinolysis is used to dissolve the fibrinogen and to provide the first component, and a solution of calcium chloride is also used to provide the second component. From July to December in 1990, during 6 months, we used fibrin sealant in the 28 patients of 33 various cases, in the following ways; supportive application of fibrin sealant after free autogenouse nerve graft for the repair of inferior alveolar nerve, facial nerve or accessory nerve, treament of hemangioma or lymphangioma to thrombosize and lead to the tumor shrinking, skin grafting to stimulate the adhesion and tissue repair, bone grafting in the patients of cleft alveolus, mandibular reconstruction or orthognathic surgery to facilitate the knitting of bone chips, tissue adhesion after tumor resection, radical neck dissection or flap reconstructions, and supportive adhesion of external auditory cannal after TMJ surgery via postauricular approach. No adverse effects were observed, none of the patients developed hepatitis or other blood transmitted disease, and the wound healing were acceptable.

• Journal of Korean Society of Steel Construction
• /
• v.9 no.3 s.32
• /
• pp.421-430
• /
• 1997

In this study, the static and the fatigue tests were performed with high tension bolted joints, of which the surfaces were spread with inorganic zinc-primer after shot-blast, and milling surface, and steel-natural surface, difference of friction surface condition were examined by comparing the esults of tests. From the result of synthetical investigation of this study. it is proper that using the torque management method in order to introduce design axial force to blots, and the provision of specifications that initial axial forces must be 110% of design axial forces is proper. Decreasing ratio of axial forces to initial force is proportional to common lorgarithms of time progress, it converge constant value after 20 hours, and decreasing ratio is little related to the roughness of friction surface. Sliding coefficient of milling, spreading inorganic zinc-primer, just producting is great in order and sliding forces are dependent on the applied axial forces, but if the applied axial forces are great, sliding coefficient become small by a loss of roughness. So it is confirmed that relation between the applied axial forces and the sliding forces are not proportional linearly. From the result of estimation on fatigue strength, all specimens satisfy the specifications with B-grade and milling surface is lower than the others about 14% in fatigue strength because in milling surface lose the function of friction-types joints at lower number of cycles. From the result of eximination for the distribution area of compressive force, friction area near to inside bolt is wider in the direction of stress than near to outside. It is guessed that this situation occurs because outside bolts firstly change from the friction connection to the bearing connection.

• Journal of the Korean Electrochemical Society
• /
• v.12 no.2
• /
• pp.148-154
• /
• 2009

With respect to the durability of large scale ($150cm^2$) membrane electrode assembly (MEA) of direct methanol fuel cell (DMFC), degradation phenomena at cathode is monitored and analyzed according to the position on the cathode surface. After constant current mode operation of large scale MEA for 500 hr, the MEA is divided into three parts along the cathode channel; (close to) inlet, middle, and (close to) outlet. The performance of each MEA is tested and it is revealed that the MEA from the cathode outlet of large MEA shows the worst performance. This is due to the catalyst degradation and GDL delamination caused by flooding at cathode outlet of large MEA during the 500 hr operation. Particularly on the catalyst degradation, the loss of electrochemically active surface area (ECSA) of catalyst gets worse along the cathode channel from inlet to outlet, of which the reason is believed to be loss of catalysts by dissolution and migration rather than their agglomeration. The extent of loss in the performance and catalyst degradation has strong relation to the cathode flooding and it is required to develop proper water management techniques and separator channel design to control the flooding.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.5 s.72
• /
• pp.609-619
• /
• 2004

An investigation was conducted on the activities around Europe in order to solve the problem of the thermal bridging of steel studs, which had caused a significant disadvantage. This study included the following: diminishing the contact area between the studs and the sheathing, lengthening the heat transfer route, replacing the steel web with a less conductive material, and placing foam insulation in locations where the thermal shorts are most critical. Although energy efficiency is usually the focus of such foreign cases because their stud application is mostly limited to low-rise residential buildings, both structural and thermal performance are taken into consideration in this study because these target middle-story buildings. A hybrid stud composed of steel and polymer was also developed. This hybrid stud, which is 150 SL in size, is made of a galvanized steel sheet (SGC58) and a glass fiber reinforced polymer (GFRP) withepoxy bonding. A total of 32 specimens were manufactured. Its parameters comprise two types of connection detail,s: the thickness of steel (1.0mm and 1.2mm) and of the GFRP (4mm-4ply and 6mm-6ply), and the ratio of the length to the depth (L/D = 3, 6, 9, 12). Steel stud specimens with the same conditions were compared to the hybrid stud. The test revealed that in the case of the steel specimen with a thickness of 1.0mm, the maximum load of hybrid studs increased an average of 1.62 times comparedto that of the steel stud. In the case of the steel specimen with a thickness of 1.2mm, on the other hand, the average increase was 1.46times. All specimens showed full composite action until the collapse.

• Journal of the Korean Magnetics Society
• /
• v.10 no.4
• /
• pp.159-163
• /
• 2000

MR characteristics in magnetic tunnel junction using CoO as the oxide barrier were investigated. Spin-dependent tunnel junctions were fabricated on 4$\^$o/ tilt-cut (111)Si substrates in 3-gun magnetron sputtering system. The top and bottom ferromagnetic electrodes were Ni$\_$80/Fe$\_$20/(300 $\AA$) and Co(300 $\AA$), respectively. The oxide barriers (CoO) were formed by the thermal oxidation at room temperature in an O$_2$ atmosphere and the plasma oxidation. The increase of coercive field due to antiferromagnetic-ferromagnetic coupling has been observed in O$_2$plasma-oxidized CoO based junctions at room temperature. At a sensing current of 1 mA, MR ratios of O$_2$plasma-oxidized CoO based junction and thermal-oxidized CoO based junction at room temperature were 1% and 5%, respectively. Larger MR ratios are observed in magnetic tunnel juctions with thermal oxidized CoO when sensing current more than applied 1.5 mA. At a sensing current of 1.5 mA, we have observed MR value of 28 % and specific resistance (RA=R$\times$A) value of 10.9 ㏀$\times$㎛$^2$. When specific resistance values reached 2.28 ㏀$\times$㎛$^2$, we have observed that MR ratios become as high as 120%.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 1998.05a
• /
• pp.60-60
• /
• 1998

아연도금강판은 내식성이 우수하여 자동차용 강판으로 널리 쓰이고 있다. 자동차용 강판은 spot 용접에 의해서 각 부분들이 접합되는데 도금층으로 사용되는 아연은 강판보다 융점이 낮아서 용접작업을 저하시킨다. 현재 사용되는 작업조건에서 용접 타 접수가 평균 2000회를 넘게되면 용접되는 부위의 면적이 감소되어 접합강도가 떨어지게된다. 따라서, 아연이 도금된 강판을 용접하게되면 작업성이 저하되므로 도금층의 성분에 대한 변화를 주므로서 이에 대한 개선을 할 필요가 있다.. Cole, Dickenson 및 Kimchi 등은 도금충내의 알루미늄을 0.1~0.5%(중량비) 함유하는 아연도금강판은 저항용접시 도금충내의 알루미늄 함량에 따라 용접성이 영향을 받는다고 보고하였다. 전극수명은 도금층내의 알루미늄 함량이 증가할수록 떨어지는데 알루미늄이 0.5% 이 하로 함유된 아연도금강판의 경우는 용접타접수가 2000~6000회에 이르르나 알루미늄 이 50%이상 함유된 합금도금강판은 200-600회에 불과한 것으로 나타난다. H. M Matsuda 등은 도금층의 알루미늄이 용접성에 영향을 미치는 이유로서 도금층의 용융 온도 변화를 지적하였다. 도금충내에 알루미늄의 함량이 높게되면 철과 아연의 확산에 의한 합금화 반응이 저하되어 도금층의 용융온도가 높아지지 못하므로 용접성이 나빠지게 된다. 본 연구에서는 아연도금욕의 조성은 기존의 상태로 유지하고 제3의 원소를 첨가하여 도금층에 함유되는 알루미늄의 양에 미치는 효과를 조사하였다. 도금층의 불성변화 및 그에 따른 내식성을 조사하였으며 도금층의 조직변화도 함께 관찰하였다. 아울러 첨가원소에 의한 도금욕의 특성도 평가하였다. 첨가원소에 의해서 도금충내의 알루미늄 함량은 감소하는 경향을 나타내었으며 도금층의 물성은 주어진 조성범위 내에서 별다른 변화를 나타내지 않았다.brittlement)기구도 제안되고 었다. 원전의 냉각수는 고 순도의 물이지만 수 처리 과정과 웅축기 배관의 누수로 인한 산소, $Cu^{2+},{\;}S_xO_6{\;}^{2-}(x=3~6)$ 등이 유입되어 오염되는데 이려한 오염물질들이 수 ppm정도 소량 포함된 경우 응 력부식민감도는 상당히 증가된다. 산성분위기 흑은 산소, $Cu^{2+}$, 등이 소량 포합된 산화성 분위기 그리고 sufur oxyanion 에 오염된 고온의 물에서 600 의 IGSCC 민감도는 예민화도가 증가할 수록 민감하여 304 의 IGSCC 와 매우 유사한 거동을 보인다. 본 강연에서는 304 와 600 의 고온 물에서 일어나는 IGSCC 민감도에 미치는 환경, 예민화처리, 합금원소의 영향을 고찰하고 이에 대한 최근의 연구 동향과 방식 방법을 다룬다.다.의 목적과 지식)보다 미학적 경험에 주는 영향이 큰 것으로 나타났으며, 모든 사람들에게 비슷한 미학적 경험을 발생시키는 것 이 밝혀졌다. 다시 말하면 모든 사람들은 그들의 문화적인 국적과 사회적 인 직업의 차이, 목적의 차이, 또한 환경의 의미의 차이에 상관없이 아름다 운 경관(High-beauty landscape)을 주거지나 나들이 장소로서 선호했으며, 아름답다고 평가했다. 반면에, 사람들이 갖고 있는 문화의 차이, 직업의 차 이, 목적의 차이, 그리고 환경의 의미의 차이에 따라 경관의 미학적 평가가 달라진 것으로 나타났다.corner$적 의도에 의한 경관구성의 일면을 확인할수 있지만 엄밀히 생각하여 보면 이러한 예의 경우도 최락의 총체적인 외형은 마찬가지로 $\ulcorner$순응$\lrcorner$의 범위를 벗어나지 않는다. 그렇기 때문에도 $\ulcorner$

• Journal of Korean Society of Forest Science
• /
• v.105 no.3
• /
• pp.309-314
• /
• 2016

A locally adapted plant population under harsh environmental changes might survive for a long generation through maintaining proper level of genetic diversity. When it happens losing the genetic diversity too much fast, the population could be declining and probably become extinct. An isolated small population of Populus davidiana was investigated to study out the genetic diversity and the fine-scale spatial genetic structure. The estimated number of adult trees in the population of Mt. Worak, South Korea, was 350 in the total area of $14,000m^2$. The number of adults in a study plot ($70m{\times}70m$) was 123. The average age was 16-year-old and a 32-year-old tree was the oldest. The distribution of individuals was slightly aggregated in the plot. Sixty-one among the 123 individuals were randomly sampled to estimate genetic variation using AFLP markers. One hundred fifty-one (77%) of total 196 amplicons were polymorphic from six AFLP primer combinations. The average number of loci per primer combination was 32.7 (S.D.=7.2). Expected heterozygosity ($H_e$) and Shannon's diversity index (S.I.) were 0.154 and 0.254, respectively. These values were extremely lower than those of other P. davidiana populations in South Korea. Genetic patchiness was showed within 21 meters by spatial autocorrelation analysis and the isolated small size of population might be mainly attributed to the formation of such small patch size.