• Journal of Welding and Joining
• /
• v.28 no.4
• /
• pp.73-80
• /
• 2010

In this work, the effect of welding variables on weldability of gas tungsten arc(GTA) welding was investigated with experimental analysis for a commercial pure(CP) titanium (Grade.1). The GTA welding tests on sheet samples with 0.5mm in thick were carried out at different process variables such as arc length, welding speed and electrode shape. In order to search an optimum arc length with full penetration, bead- on-plate welding before butt-welding were performed with different arc length conditions. From the bead- on-plate welding results, the optimum condition considering arc stability and electrode loss was obtained in the arc length of 0.8mm. Butt-welding tests based on the arc length of 0.8mm were carried out to achieve the optimum conditions of welding speed and electrode shape. Optimum conditions of welding speed and electrode shape were suggested as 10 mm/s and truncated electrode shape, respectively. It was successfully validated by the microstructural observation, tensile tests, micro-hardness tests and formability tests.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.10
• /
• pp.1195-1203
• /
• 2012

Welding is a well-developed, widely used process for permanently joining metal components. However, the mechanical reliability of welded parts still offers room for improvement. A weld region consists of a fusion zone, a partially melted zone, and a heat-affected zone, and each zone has different material properties. In addition, the geometrical shape of a weld bead or fillet influences the mechanical reliability. A precise structural analysis must consider how a local welded region influences the mechanical behavior of the entire structure. This study focuses on an effective modeling scheme for the weld region. It relies on experimental and numerical methods to determine the proper correlation based on experimental results and to propose a modeling scheme for welded parts.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.10
• /
• pp.1347-1353
• /
• 2011

Friction stir welding (FSW) method has extensively been used in manufacturing methods because of the several advantages over conventional welding methods, such as better mechanical properties, reduced occurrence of joining defects, high material saving, and low production time, etc. The aim of this paper is to review the optimal FSW conditions using the previous experimental results and is to investigate the fatigue crack growth rate in three different zones, WM, HAZ and BM for FSWed Al7075-T651 aluminum plates. As far as our experiments are concerned, the optimal conditions are obtained as rotation speed, 800rpm and travelling speed, 0.5mm/sec. The fatigue crack growth rate showed strong dependency on three different zones WM, HAZ and BM, and crack driving force.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.88.1-88.1
• /
• 2011

SOFC는 사용되는 셀의 디자인에 따라 튜브형, 평판형으로 구분되어진다. 평판형의 경우에는 전해질 지지형(ESC), Anode 지지형(ASC) 및 금속 지지형(MSC)로 크게 나눌 수 있다. SOFC 스택은 이와 같은 셀과 밀봉재, 집전체, 분리판의 구성요소를 여러 장으로 적층하여 이루어진다. SOFC 발전시스템은 SOFC 스택과 EBOP, MBOP로 구성되는데, SOFC 발전시스템의 상용화를 위해 선행되어야 할 것은 스택의 안정적 출력 및 신뢰성 확보이다. 즉, 셀, 밀봉재, 분리판 및 집전체로 대변되는 구성요소들이 스택에 장착되었을 때 그 기능을 최대한 발휘하면서도 점진적 또는 급격한 품질저하가 발생되지 말아야 한다. 특히, 밀봉재의 경우 SOFC에 사용되는 연료와 공기의 혼합(Cross-over)을 방지하는 중요한 기능을 담당하고 있으며 여러 장 적층된 분리판의 전기적 단락을 방지해야 한다. 또한 SOFC의 특성상 $700^{\circ}C$ 이상의 고온에서 다른 구성요소와 화학적 반응이 없어야하고 열싸이클(Thermal cycle)을 견딜 수 있도록 충분한 기계적 강도가 보장되어야 하는 등 요구되는 품질기준이 엄격하다. SOFC의 밀봉재는 접합형(Brazing), 압착형(Compressive), 용융-고정형(Glass-ceramic)이 대표적으로 적용되고 있다. 이 중에서 Brazing 물질과 방법은 현재 활발히 연구가 수행 중에 있지만 범용적으로 사용되고 있지는 않은 상태이고 Compressive 밀봉재와 Glass-ceramic 밀봉재가 대면적 SOFC 스택에 사용되어 적용 가능성을 평가받고 있다. 본 연구에서는 SOFC 구성요소의 국산화를 추진하는 지경부과제의 결과물 중 (주)써모텍에서 개발한 Glass-ceramic 밀봉재(RC1) 단품에 대한 특성평가와 실제 단전지 평가를 통해 SOFC 스택 적용 가능성을 평가하였다. 밀봉재 단품에 대한 특성평가는 용융특성, 상분석, 열팽창계수 등의 물리적, 화학적 평가 외에 가스 누설 정도를 평가하는 기밀도 평가와 SOFC의 작동 온도인 $700^{\circ}C$와 상온 분위기를 주기적으로 인가하는 Thermal cycle 특성을 평가하였다. 셀을 한 장 사용하는 단전지(Unit cell) 평가는 RIST에서 자체 제작한 $100{\times}100mm^2$ 평판형 ASC 셀을 사용하여 수행하였으며, 밀봉재는 Dispensing 공정을 통해 구성되었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.387-387
• /
• 2012

결정 Si 및 비정질 Si 태양전지는 환경친화적이며 안정적인 물질로 전력변환 및 에너지 저장 장치에 중요하기 때문에 연구가 활발하게 진행되고 있다. 고효율 Si 태양전지를 제작하여 상용화하기에는 여러 가지 문제점이 있다. 공기와 비교하여 높은 굴절률을 갖고 있기 때문에 발생하는 반사를 줄이기 위해서 필요한 무반사 코팅층(Anti-reflective coating; ARC)은 주로 SiO2 와 SiNx 와 같은 유전체를 이용하여 사용하지만 이들 ARC 증착은 PECVD와 같은 진공장비를 사용하므로 제작 비용이 높아지는 단점이 있다. 나노선 또는 나노 팁과 같은 sub-wavelength 구조를 표면에 만들어 반사율을 줄이는 작업을 통해 ARC 공정비용을 감소하고 효율을 증진하는 연구가 활발히 진행되고 있다. CdS 양자점을 태양전지 표면에 형성함으로 ARC로 해결할 수 없는 단파장영역에 해당하는 부분을 줄이는 연구가 진행되었으며, 비정질의 경우 원기둥 형태의 태양전지 형태와 더불어 지름 방향으로의 PN 접합 나노로드 배열을 만들어 흡수면을 증가하여 효율을 증가한 연구도 진행되었다. 태양전지 표면의 형태를 V-groove 형태로 형성하여 입사하는 태양전지의 광밀도를 증가하는 이론적 결과도 발표되었다. 본 연구에서는 Si 태양전지의 표면변형에 따른 태양전지의 전력변환효율의 변화를 관찰하기 위하여 태양전지 표면의 texture 지름을 $3{\sim}15{\mu}m$, 간격을 $5{\sim}20{\mu}m$로 변화하고, 태양전지 표면의 나노 패턴을 2~10 nm 로 변화하여 반사율과 전력변환효율을 비교하였다. 나노와 마이크로 패턴은 각각 polystyrene nanosphere 와 photo mask를 이용하여 제작하였으며 PN junction Si 태양전지는 spin on dopant 방식으로 제작하여 성능을 조사하였다.

• Journal of the Semiconductor & Display Technology
• /
• v.13 no.3
• /
• pp.45-50
• /
• 2014

In this paper, we propose a super-junction MOSFET (SJ MOSFET) fabricated through a simple pillar forming process by varying the Si epilayer thickness and doping concentration of pillars using SILVACO TCAD simulation. The design of the SJ MOSFET structure is presented, and the doping concentration of pillar, breakdown voltage ($V_{BR}$) and drain current are analyzed. The device performance of conventional Si planar metal-oxide semiconductor field-effect transistor(MOSFET), Si SJ MOSFET, and SiGe SJ MOSFET was investigated. The p- and n-pillars in Si SJ MOSFET suppressed the punch-through effect caused by drain bias. This lead to the higher $V_{BR}$ and reduced on resistance of Si SJ MOSFET. An increase in the thickness of Si epilayer and decrease in the former is most effective than the latter. The implementation of SiGe epilayer to SJ MOSFET resulted in the improvement of $V_{BR}$ as well as drain current in saturation region, when compared to Si SJ MOSFET. Such a superior device performance of SiGe SJ MOSFET could be associated with smaller bandgap of SiGe which facilitated the drift of carriers through lower built-in potential barrier.

• Journal of Welding and Joining
• /
• v.32 no.1
• /
• pp.15-21
• /
• 2014

FCAW(Flux Cored Arc Welding), SAW(Submerged Arc Welding), EGW(Electro Gas Welding), and three-pole SAW are applicable in manufacturing the offshore wind tower. In this paper, mechanical properties of these welded-joints for TMCP steels were evaluated in all above welding processes. The tensile strength of welded-joints for all the welding methods satisfied the standard guideline (KS D 3515). No cracking on weldment was found after the bending test. Changes of weldedments hardness with welding processes were observed. In a weld HAZ (heat-affected zone), a softened HAZ-zone was formed with high heat input welding processes (SAW and EGW). However, the welded-joint fractures were found in the base metal for all cases and small decrease in welded-joint strength was caused by a softened zone. The multi-pole SAW welds exhibited similar mechanical properties comparing to the one with one-pole SAW process.

• Journal of Welding and Joining
• /
• v.32 no.1
• /
• pp.6-14
• /
• 2014

This paper has an aim to evaluate microstructure and fracture toughness of TMCP steel weldment applied for off-shore wind tower with the focus on the effect of heat input on the weldment with various welding processes; FCAW(13kJ/cm and 30kJ/cm), SAW(62kJ/cm), and EGW(177kJ/cm). Based on experimental results developed from this study, it was found that the impact toughness of top side for TMCP steel weldments with heat input up to 62 kJ/cm satisfied the required minimum value except the EGW(177kJ/cm). The heat input and microstructure are the main factors of impact toughness. The heat input of 13kJ/cm on back side with low heat input increased the amount of grain boundary ferrite which has low impact toughness, and heat input of 177kJ/cm on top side is significant enough to produce the austenite grain growth. The compositions and sizes of inclusions which are the dominant factors for the formation of acicular ferrite were analyzed by OM and EDS. As the heat input increased, the inclusions also grew and a nucleation site decreased. The size of nonmetallic inclusions and the crack width was nearly similar, therefore the inclusions were related with the crack propagation.

• Journal of Welding and Joining
• /
• v.32 no.2
• /
• pp.22-28
• /
• 2014

To enhance productivity and provide high quality production material in a GMA welding process, weld quality, productivity and cost reduction affects the number of process variables. In addition, a reliable welding process and conditions must be implemented to reduce weld structure failure. In various industries the welding process mathematical model is not fully formulated for the process parameter and on the welding conditions, therefore only partial variables can be predicted. The research investigates the interaction between the welding parameters (welding speed, distance between electrodes, and flow rate of shielding gas) and bead geometry for predicting the weld bead geometry (bead width, bead height). Taguchi techniques are applied to bead shape to develope curve equation for predicting the optimized process parameters and quality characteristics by analyzing the S/N ratio. The experimental results and measured error is within the range of 10% presenting satisfactory accuracy. The curve equation was developed in such a way that you can predict the bead geometry of constructed machinery that can be used for making tandem welding process.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.3
• /
• pp.581-593
• /
• 1990

A semi-solid alloy in which solid and liquid phase are co-existing is obtained by strirring of Al7075 molten metal. A semi-solid alloy is dependent on the corresponding temperature within the solid-liquid range, and the process parameters should be controlled accurately to obtain the homogeneous semi-solid alloy. The possibility o homogeneous fiber-reinforce aluminum alloy by addition of $Al_{2}$O$_{3}$ short fibers with vigorous agitation was investigated. The billet of composite materials was fabricated by squeeze casting, and homogeneous dipersion state of fibers in billet of fabricated metal matrix composites was observed. A slurry of semi-solid short fiber metal matrix composites is used in the direct rolling process, and this process showed the fabrication possibility of metal matrix composite sheets. The fabricated sheet was tested regarding vickers hardness, elongation and micro-structure. It has become clear that mashy state processing and working are very useful to obtain parts of composites material closed to near net shape.