• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.3
• /
• pp.367-372
• /
• 1985

본 연구에서는 Heuer는 원추형 애자의 해석을 ANSYS프그램을 사용하여 시도하 였으나 시멘트와 자기간의 접촉문제를 다루지 않았고, Iwama와 Kito는 이에 대한 언급 이 없이 유한요소법에 의한 자기내부의 응력분포 결과와 실험식과를 개략적으로 비교 하였다. Fig. 1은 현수애자의 외관과 단면도이다. 철재의 핀(Pin)과 캡(cap), 자 기, 철재와 자기를 접착시키는 시멘트(cement), 접촉면의 불균일 상태를 보상시키는 역청(bituminous layer), 그리고 시멘트와 자기간의 사층(sand band)으로 구성되어 있 는 현수애자의 핀의 하단에서 송전선 무게의 하중이 가해지고 캡의 홈으로 다른 애자 가 연결되어 송전탑에 부착된다. 본 해석에서는 핀의 하단에 정적으로 사용하중이 가해진다고 가정하였다.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.8
• /
• pp.84-91
• /
• 2002

This paper analyzes the subsurface stress at the spherical contact using Hamilton equation, and with that data, calculates the fatigue limit under the variations of friction coefficient using fatigue theory. After rough surface being made, this paper figures out the random load generated by contacting to the rough surface, analyzes the stress of its subsurface, and calculates the fatigue limit of the rough surface using fatigue theory. The three parts of the fatigue theory are applied, which are critical plane theory, stress invariant theory and mesoscopic theory.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1997.04a
• /
• pp.41-46
• /
• 1997

TiN 코팅은 마모에 대한 저항성 및 고체 윤활 효과가 매우 우수하여 내마모성 및 저마찰이 요구되는 절삭공구나 피스톤 베어링 및 각종 축계의 코팅막으로 사용이 증가되고 있다. 일반적으로 재료의 경도와 인성은 서로 상반 관계를 갖고 있어 공학적으로 경도와 인성을 모두 요구하는 표면을 얻기 위해 연질 모재 위의 세라믹 코팅은 그 요구를 만족시킬 수 있는 가장 각광받는 표면처리 방법중의 하나이다. 그러나, TiN과 같은 경질 박막의 공학적 적용시 가장 요구되는 마모수명은 모재의 조도나 경도, 증착 방법, 접촉 상태, 코팅막의 두께 및 마모의 발생 기구 등에 따라 마찰 및 마모 메커니즘의 현저한 차이를 나타내기 때문에 예측이 거의 불가능한 실정이고, 아직까지 이러한 마모수명 비교 평가방법에 대한 기준 설정 및 정량적 정립이 이루어지지 않고 있다. 본 연구에서는 모재의 경도, 조도, 코팅 두께가 다른 TiN 경질 박막에 압입시험과 스크래치시험시 발생되는 균열 발생 메커니즘과 미끄럼 시험시 발생되는 마모 메커니즘의 연계성을 밝히고 압입 및 스크래치 시험시 코팅막이 손상되는 임계하중과 미끄럼 시험시 접촉하중 변화에 따른 마모수명의 정량적 연관성을 찾아보고자 한다.

• Tribology and Lubricants
• /
• v.25 no.6
• /
• pp.367-373
• /
• 2009

Many research of elastohydrodynamic lubrication (EHL) has been performed under the condition of steady state loading. However, mechanical elements undergo severe high loads that are in the fluctuating modes of frequency and amplitude. Conventional numerical method for the circular contact of EHL study has the difficulty in making the film thickness and pressure of EHL converged in high loads of steady state as well as fluctuating loading conditions. In this work, multigrid multilevel method are used for the stable convergence of film pressure and thickness under the conditions of high as well as varying loads, and very stable solutions of film behaviors with elastic deformation are obtained. Several results of dynamic loading condition are shown and compared with those of steady state condition in the aspects of circular EHL film thickness and pressure.

• Tribology and Lubricants
• /
• v.29 no.1
• /
• pp.33-38
• /
• 2013

This study is aimed to predict the fatigue life for pitch bearings under combined radial, thrust load and moment. In order to do this, a series of simulation such as bearing load distribution, initial surface stress, subsurface stress and fatigue analysis is needd. Fatigue life for pitch bearing can be predicted by using a bearing's material fatigue property.

• Korean Journal of Materials Research
• /
• v.8 no.4
• /
• pp.293-298
• /
• 1998

The fracture behavior of $Si_3N_4N$, coated $Si_3N_4N$-BN composite was studied by the Hertzian indentation technique. New types of contact-induced cracks were found, and it was confirmed that these cracks have cone crack geometry. Contact damage was distributed in the substrate layer, which can absorb energy, as well as in the coating layer, so the propagation of initiated cracks in the coating layer were suppressed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.502-505
• /
• 2005

To overcome some of the limitations in the conventional photolithography technique, MC-SPL which has advantages such as flexibility and high speed was developed in the past. To make a fine pattern using MC-SPL, there are many variables to control, for example, applied load, scribing speed, chemical etching condition, and etc. In this work, the effect of contact load on the width of the pattern was investigated. The load not only influences the width of the pattern but it also affects the wear of the probe tip. It was found that it is beneficial to load the tip in two stages. Futhermore, the experimental results showed that the pattern width was more sensitive to the initial contact force.

• Journal of the Korea Convergence Society
• /
• v.11 no.11
• /
• pp.239-247
• /
• 2020

This study is about design and verification of stress reduction of bearings for wind turbines. In a slewing bearing having a typical four-contact structure, the contact point moves to the end of the raceway due to a large moment load, resulting in a stress concentration. A bearing was designed to reduce such contact point movement. The deformation behavior of typical ball bearings and newly designed bearings was calculated through finite element analysis under ultimate load by replacing the ball with a spring element. The contact stress between the ball and the raceway was calculated by finite element analysis by inputting the deformation behavior analysis result as a boundary condition. The effectiveness of the bearing stress analysis method using spring elements was verified through comparison of the contact stress according to the bearing structure.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.29 no.1
• /
• pp.45-58
• /
• 2013

The purpose of this study was to analyze the area of occlusal contact points using visual method. One subject was selected who had Angle Class I, normal dentition, without dental caries, periodontal disease and temporomandibular disorders. Forty times PVS impressions were taken and 10 pairs casts were fabricated using dental super hard stone. After mounting the casts with customized loading apparatus, 78.9kg/f force was loaded as a maximum biting force. In T-Scan method, occlusal contact points measurement was repeated twice. Then, using Photoshop program (Adobe photoshop CS3, Adobe. San Jose, USA), the pixels which indicated occlusal contact points by color was recognized, and the distribution of recognized pixels were calculated to area. In Add picture method, polyether bite material applied to the occlusal surface of the casts. Then, the image of the translucent areas was recorded and classified $0{\sim}10{\mu}m$, $0{\sim}30{\mu}m$, $0{\sim}60{\mu}m$ area by the amount of transmitted light. To acquire occlusal surface, the numbers of pixels from the photograph of the contact area indicated cast converted to $mm^2$. The mean occlusal contact area by two methods was statistically analyzed (paired t-test). Part of the red and pink area in T-Scan image were almost equivalent to the $0{\sim}10{\mu}m$, $0{\sim}30{\mu}m$, $0{\sim}60{\mu}m$ area in Add picture image. The distribution of occlusal contact points were similar, but the average area of occlusal contact points was wider in T-scan image (P<.05). Pink and red area in T-scan image was wider than $0{\sim}10{\mu}m$, $0{\sim}30{\mu}m$ area in Add picture image (P<.05), but similar to $0{\sim}60{\mu}m$area in Add picture image (P>.05). Occlusal contact points in T-scan image did not indicate real occlusal contact points. Occlusal contact areas in T-scan method were enlarged results comparing with those in Add picture method.

• Tunnel and Underground Space
• /
• v.19 no.6
• /
• pp.545-557
• /
• 2009

In order to investigate dynamic damage mechanism of brittle materials, Split Hopkinson Pressure Bar (SHPB) have been adapted to apply different impact levels to rocks in South Korea. High resolution X-ray Computed Tomography (CT) was used to estimate the damage in tested rock samples nondestructively. The cracks which are parallel to the loading axis are visible on the contact surface with the incident bar under lower level of impact. The surface cracks disappeared with increment of impact level due to confined effect between the incident bar and sample, while axial splitting are happened near the outer surface.