• Composites Research
• /
• v.33 no.5
• /
• pp.275-281
• /
• 2020

The mechanical property related to lap shear strength of the joint structure between carbon fiber reinforced polymer (CFRP) composite and metal (Ni-Cr Alloy) under varying environmental conditions (temperature and humidity) was studied in order to apply to the aircraft fan blade. Room temperature dry (RTD), elevated temperature wet (ETW), and cold temperature dry (CTD) environmental conditions were chosen for investigation based on the flight conditions of aircraft. Lap shear strength tests were conducted according to ASTM Standard D3528 to evaluate the shear strength. The microstructure characteristic of failure zone was analyzed by SEM images to check the adhesive shear strength with the three environmental conditions. In comparison with shear strength for the RTD condition, the shear strength in the ETW condition was reduced by 72.8% while those for the CTD condition increased by 56.5%. The moisture absorption and high temperature in ETW condition strongly had an affect on mechanical property of adhesive, while cold temperature could enhance the adhesive shear strength due to the higher brittleness.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.4
• /
• pp.382-390
• /
• 2011

Smart sensors embedable in composite wind turbine blades have been required to be researched for monitoring the health status of large wind turbine blades during real-time operation. In this research, the feasibility of packaged FBG sensor probes was studied through the experiments of composite blade trailing edge specimens in order to detect cracking and debonding damages. The instants of cracking and debonding generated in the shear web were confirmed by rapid changes of the wavelength shifts from the bare FBG sensor probes. Packaged FBG sensor probes were proposed to remove the fragile property of bare FBG sensor probes attached on composite wind blade specimens. Strain and temperature sensitivity of fabricated probes installed on the skin of blade specimen were almost equal to those of a bare FBG sensor. Strain sensitivity was measured to be ${\mu}{\varepsilon}$/pm in a strain range from to 0 to 600 ${\mu}{\varepsilon}$, and the calculated temperature sensitivity was to be 48 pm/$^{\circ}C$ in the heating test up to 80 degree.

• International Journal of Highway Engineering
• /
• v.13 no.1
• /
• pp.139-148
• /
• 2011

Asphalt concrete overlay method is used by general maintenance and rehabilitation of construction for aged concrete pavement in Korea. However, in case of the AC overlay method to extend service life of the existing concrete pavements, various distresses of reflection crack, pothole and rutting are the typical problems of the asphalt overlay on existing concrete pavement since it has different physical characteristics between asphalt overlay and existing concrete pavement. To achieve this, application of concrete overlay method is required instead of AC overlay method. Concrete overlay method has advantages that can reduce maintenance cycle and costs since it has excellent bearing value for heavy vehicles and no rutting. However, technical problems of detour road construction, traffic control and other disadvantages happened by long curing time. Thus, in this study and experimental research were launched to evaluate the workability, durability and resistance against environmental loading of Very Rapid Hardening Acrylic Polymer Modified Concrete(VRH-APMC) for application of bonded concrete overlay method. Test results showed that the compressive and bond strength were exceed 21MPa and 1.4MPa of target strength after four hours for rapid traffic opening properties. And tests of resistance against environmental loading results showed that VRH-APMC secured excellent durability. Thus, it was known that VRH-APMC was suitable material for large scale bonded concrete overlay method, and it was possible to use maintenance and rehabilitation method which needs enough workability and rapid traffic opening.

• Journal of Conservation Science
• /
• v.26 no.4
• /
• pp.371-376
• /
• 2010

The great jar estimated in Proto-Three Kingdoms period was found at the site from Pyeongtaek Daechuri and the bonding traces from pieces destroyed when they were excavated are observed. Therefore this study would figure out the components of bonding material used in great jars by optical microscope, FT-IR, py-GC/MS and the kind of textile attaching to great jar by transmitted light microscope. As a result of optical microscope for the cross-section, black material is uniformly applied between a piece of jar and the part of bonding and the textile line are observed. Black bonding material is resulted in korean rhus lacquer by FT-IR and py-GC/MS and the kind of textile is identified as hemp by transmitted light microscope. Materials for repairing archaeological objects are hardly known causing little information, but this study proves that the bonding material had used lacquer for great jars before Proto-Three Kingdoms period. Therefore if ancient bonding materials are systematically analysed in the further studies, it would be significant help for studying bonding and restoration materials of ancient objects.

• Composites Research
• /
• v.28 no.6
• /
• pp.356-360
• /
• 2015

In this paper, the carbon fiber reinforced plastic is processed as the double cantilever beam in order to estimate the fracture behavior of composite and is carried out with the static analysis as the mode I. The specimen sizes are 25 mm, 30 mm, 35 mm and 40 mm. And the material property is used with carbon. As the analysis result of mode I, the adhesive part is detached latest by the small force at the specimen thickness of 25 mm. The largest force is happened at the specimen thickness of 40 mm. The defection of the adhesive interface is shown slowest at the displacement of 9.75 mm at the specimen thickness of 25 mm. And the defection is shown quickest at the displacement of 7.82 mm at the specimen thickness of 40 mm. This defection is due to the fracture of specimen. The result of this study on the defection of the adhesive interface and the reaction force due to this defection is thought to be contributed to the safe structural design of the carbon fiber reinforced plastic.

• Composites Research
• /
• v.32 no.2
• /
• pp.90-95
• /
• 2019

Sloshing impact loads on liquefied natural gas (LNG) carr iers are the main issue of damage to the insulation system in LNG cargo containment system (LNG CCS). The damage to the insulation system would be fatal in maintaining a temperature-savings environment in LNG CCS. The typical method is to enhance the insulation materials that can maintain a constant cryogenic temperature. Insulation materials consist of polyurethane foam and plywood, an adhesive for bonding these two materials. This study intends to improve the absorption energy of the material when the impact load is applied by creating a glass bubble/epoxy composite resin as part of the insulation. The experimental scenarios consider the effect of temperature ($20^{\circ}C$, $-163^{\circ}C$), glass bubble weight fraction in epoxy resin through free fall experiments. Experiments have shown that if the glass bubble additive reaches 20 wt.%, the cryogenic absorption energy is a maximum performance and that 0 wt.% has a maximum ambient absorption energy. However, the agglomeration has been occurred due to deterioration of the stirring performance if weight fraction was 20 wt.% and the result of 0 wt.% have been revealed that ambient absorption energy is significantly lower.

• Composites Research
• /
• v.36 no.6
• /
• pp.441-447
• /
• 2023

Recently, as demand for high-strength, lightweight materials has increased, there has been great interest in joining with metals. In the case of mechanical bonding, such as bolting and riveting, chemical bonding using adhesives is attracting attention as stress concentration, cracks, and peeling occur. In this paper, surface treatment was performed to improve the adhesive strength, and the change in adhesive strength was analyzed. For the adhesive strength test were conducted with Carbon Fiber Reinforced Plastic(CFRP), CR340(Steel), and Al6061(Aluminum), and laser and plasma surface treatment were used. After plasma surface treatment, the adhesive strength improved by 7.3% and 39.2% in CFRP-CR340 and CFRP-Al6061, respectively. CR340-Al6061 was improved by 56.2% in laser surface treatment. Surface free energy(SFE) was measured by contact angle after plasma treatment, and it is thought that the adhesion strength was improved by minimizing damage through a chemical reaction mechanism. For laser surface treatment, it is thought that creates a rough bonding surface and improves adhesive strength due to the mechanical interlocking effect. Therefore, surface treatment is effect to improve adhesive strength, and based on this paper, the long-term fatigue test will be conducted to prevent fatigue failure, which is a representative cause of actual structural damage.

• Composites Research
• /
• v.18 no.1
• /
• pp.30-37
• /
• 2005

The bending strength characteristics and local deformation behaviors of honeycomb sandwich composites were investigated using three-point bending experiment and finite element simulation with a real model of honeycomb core. Two kinds of cell sizes of honeycomb core, two kinds of skin layer thicknesses, perfect bonding specimen as well as initial delamination specimen were used for analysis of stress and deformation behaviors of honeycomb sandwich beams. Various failure modes such as skin layer yielding, interfacial delamination, core shear deformation and local buckling were considered. Its simulation results were very comparable to the experimental ones. Consequently, cell size of honeycomb core and skin layer thickness had dominant effects on the bending strength and deformation behaviors of honeycomb sandwich composites. Specimens of large core cell size and thin skin layer showed that bending strength decreased by $30\~68\%$.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.12
• /
• pp.1431-1434
• /
• 2014

The thermal barrier coating (TBC) applied to a gas turbine can be damaged by repeated thermal fatigue during operation, so an evaluation of its durability is needed. Thermally grown oxide (TGO) is generated inside the TBC in a high-temperature environment. The growth of TGO is known to be the main cause of damage to the TBC. Therefore, the durability of TBC should be evaluated according to the growth of TGO. In this research, Kim et al.'s work on the growth of TGO with aging was used as a basis for finite element analysis. The relationship between stress and aging was derived from the finite element analysis results. The durability of the TBC with aging was evaluated through a comparison between the results of the finite element analysis and a bond strength test.

• Journal of Conservation Science
• /
• v.25 no.2
• /
• pp.131-145
• /
• 2009

Goryeong Yangjeondong Petroglyph on the joint face of the bedrock (6m in width, 3m in height) composed of the green sandstone has circles and shield pattern sculptures. The rock is mainly composed of quartz, feldspar, chlorite, illite and calcite with the clay minerals. These clay minerals occur as pore lining, replacement of component and pore fillings. Investigated the weathering aspects including the connection between soluble salt and rock weathering and the stability of the bedrock with petroglyphs. The Major deterioration aspect are grain peel-off, surface exfoliation, cracks and damage. And the bedrock where the joints and cracks advance is interpreted with the fact that has the possibility of the falling rock. For conservation, adhesive need to cover crack and damage and consolidation is necessary in the surface which becomes weak.