• Applied Chemistry for Engineering
• /
• v.29 no.4
• /
• pp.399-404
• /
• 2018

This study compared the tackiness and adhesion of different tire tread compounds and rubber cements before and after vulcanization. The tackiness of natural rubber (NR) cement was the highest for all tread compounds before vulcanization, and the decrease in tackiness of NR cements over time was smaller than that of synthetic rubber cements. The tackiness before vulcanization was affected by the glass transition temperature of the rubber used in the cement and the decrease in tackiness over time of NR was smaller compared to that of using the synthetic rubber. The adhesion of NR-based cements after vulcanization was high for NR tread compounds but low for synthetic rubber tread compounds. On the contrary, the adhesion of emulsion (SBR) and solution SBR cements was high on all tread compounds which was shown to be higher when the rate of vulcanization of cement rubber was lower.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.4
• /
• pp.38-44
• /
• 2007

As environmental issues is important thing, our study aims to develop natural adhesives made by rosin instead of synthesis adhesive with the formaldehyde emission. Natural adhesives were formulated to enhance curing speed and adhesion performances with various drying agent contents. Adhesion performances were evaluated with tack values measured by texture analyzer and shear strengths determined by single lap shear test. The adhesion performances of nature adhesives developed in this study and compared with those of overseas natural adhesives made by AURO, BioFa, Livos. Optimum drying agent formulation was Co 0.7 part, Zr 1.0 part, Ca 0.5 part, and Activ8 0.1 part. Shear strength of the adhesives manufactured by the optimum drying agent formulation was $93.2{\pm}19.1N/cm^2$.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.1
• /
• pp.99-104
• /
• 2015

Life rafts, which has been used for domestic vessel currently, are fabricated mostly for the ocean-going vessels in accordance with the SOLAS Resolution. Therefore, there is not any small-sized life raft which can be installed on small fishery boat, leisure boat and cargo vessel with those length shorter than 20 meters in our country. However, in many foreign countries, new standards or the small-sized life rafts applicable to those small vessel have been developed according to the standard of ISO 9650. Furthermore, they make their effort to contribute the safety for the life at sea by supply the superior product of life rafts, which have been adopted by light material (i.e. thermoplastic polyurethane, TPU) and economic production process (i.e. heat sealing, radio-frequency welding, RFW), etc. In this paper, the development results of the small-sized life raft, which has been used the lightening material TPU and fabricated by RF-welding method, will be introduced.

• Composites Research
• /
• v.33 no.1
• /
• pp.1-6
• /
• 2020

Dispersion and electrical resistance (ER) properties of polyurethane (PU) type topcoat were evaluated using carbon nanotube (CNT) with different CNT weight fraction. CNT was dispersed in PU type topcoat using ultra sonication dispersion method. CNT/PU topcoat was coated on carbon fiber reinforced epoxy composite (CFRC) surface using gravity feed spraying method. Static contact angles of CFRC and CNT/PU topcoat were performed using 4 types of solvents to calculate the work of adhesion between CNT/PU topcoat and CFRC surface. Surface resistance of CNT added PU topcoat was measured to determine CNT dispersion. Adhesion property between CNT/PU topcoat and CFRC was determined via cross hatch cutting test based on ASTM D3359. The optimized condition of CNT weight fraction was found.

• Journal of the Korean Vacuum Society
• /
• v.9 no.4
• /
• pp.321-327
• /
• 2000

Tungsten(W) thin films with good adhesion property and low resistivity (~10 $\mu$\Omega$$.cm) were deposited directly on $SiO_2$ by LPCVD. The adhesion property of W thin films on $SiO_2$ improves as the temperature and/or $SiH_4/WF_6$ gas ratio increase. Specifically tungsten thin films could be deposited on $SiO_2$ even at $350^{\circ}C$ if the gas ratio of 2 was employed. The resistivity of tungsten thin films deposited at $350^{\circ}C$ was high due to the presence of $\beta$-W. However, the resistivity can be minimized by increasing the amount of $H_2$ gas flow. Therefore, it is shown in this work that the adhesion of tungsten thin films on $SiO_2$ can be improved simply by controlling the process parameters (e.g., temperature, gas ratio and $H_2$ flow rate) without employing complex deposition methods or additional glue layers.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.8
• /
• pp.4756-4762
• /
• 2014

Damaged wind turbine blades are repaired conventionally using a hand lay-up method with epoxy, where the bonding strength is not high. Epoxy has poor curing characteristics at low temperatures. The infusion method with polyester was proposed. Infusion method is believed to distribute resin uniformly. Polyester is used because it hardens better than epoxy at low temperatures. At room temperature, the proposed method increased the bonding strength by 77.7% compared to the conventional method. Using the proposed method at 15 and $5^{\circ}C$, the bonding strength increased compared to the conventional method. This paper proposes a new method for repairing wind turbine blades, even at temperatures where the conventional method cannot be used because epoxy resin does not harden. The bonding strength of the proposed method at low temperatures is higher than that of the conventional method at room temperature.

• Polymer(Korea)
• /
• v.31 no.5
• /
• pp.369-373
• /
• 2007

In this study, solvent-free pressure sensitive adhesives (PSA) using acrylic copolymer was prepared by UV radiation to investigate the effect of comonomer on the adhesion properties. Adhesive force value of PSA was increased with the amount of comonomer having shorter side chain due to the enhanced intrinsic surface energy. Peel and shear strength were also influenced by chemical properties of comonomer. The addition of comonomer, ethyl and n-butyl acrylate allows PSA sample with high peel and shear strength. This nay be explained in terms of correlation between loss modulus and glass transition temperature of PSA. As the addition of acrylic comonomers with long side chain length decreases the loss modulus of PSA, the deformation of PSA can not be inhibited.

• Polymer(Korea)
• /
• v.32 no.1
• /
• pp.1-6
• /
• 2008

The adhesion behaviors and processability of NBR as a sealing material were investigated. In order to find the optimum formulation, the adhesive properties and processability were observed as the change of the contents of acrylonitrile (ACN) in NBR. Effects of Mooney viscosity, filler, plasticizer and crosslinking agent on the adhesion behaviors were also studied. The contents of ACN in NBR have great effects on adhesion behaviors and processability in NBR sealing. To know the optimum condition of roll mixing, degree of dispersion was investigated. It was confirmed that degree of dispersion was influenced by various factors such as mixing order, time, and temperature. The crosslinking system was studied as the observation of sulfur system, peroxide system, crosslinking density, and structure. From the variation of the dry condition and hexamine contents, the relation between adhesive and NBR was studied. These results show the adhesion properties and processability are dependent on the contents of ACN and crosslinking system.

• Journal of Adhesion and Interface
• /
• v.8 no.3
• /
• pp.9-15
• /
• 2007

The interfacial evaluation of surface modified Jute fiber/polypropylene (PP) composites before and after hydration was investigated using micromechanical test and dynamic contact angle measurement. The IFSS of alkaline and silane-treated Jute fiber/PP composites increased, whereas after hydration, the IFSS of the untreated, alkaline- and silane-treated Jute fibers/PP composites decreased due to swelled fibrils by water infiltration. The interfacial adhesion of silane treated fiber/PP composites was higher than alkaline-treated or the untreated cases. The surface energies of Jute fiber treated under various conditions were obtained using dynamic contact angle measurement. Especially after hydration, the thermodynamic work of adhesion was calculated by considering water interlayer, which indicated the stability of IFSS between silane treated Jute fiber and PP matrix showing better than others.

• Journal of Adhesion and Interface
• /
• v.17 no.1
• /
• pp.21-28
• /
• 2016

Foam-type biodegradable polyurethane adhesives were developed as a non-lethal weapon against illegal fishing boats. The adhesives were prepared from a hardener of polymeric methylene diphenyl diisocyanate (MDI) and a base composed of polyester and/or polyether polyols. In order to accelerate biodegradability, starch, dextrin, and amylase were added into the base, and which present about 34% degradability within 4 weeks confirmed by OECD 301C method. For proper mixing and corresponding prompt foam reaction, viscosities of hardener and base compositions were investigated in the temperature ranges from 0 to $50^{\circ}C$. For fast completion of the foam forming and corresponding adhesion, rising time was recorded in the same temperature range, and the rising time of the adhesive was varied within around 1 minute. T-peel adhesion tests with cotton fabrics were performed which showed 20.78 N/cm and 11.95 N/cm as the maximum and the average values, respectively.