• Journal of the Korean Recycled Construction Resources Institute
• /
• v.3 no.3
• /
• pp.212-219
• /
• 2015

This study focuses evaluating the efficiency and performance evaluation of composite type sheet-membrane waterproofing method that utilizes a separation behavior inducement system designed to resolve the chronic problems of disintegration and damage of overlap areas of waterproofing layers. As the result of the test, the tensile strength value was at 13.8N/mm and elongation rate at 587% for the separation behavior inducement type specimen, and the compared specimens had 14.2N/mm for tensile strength and 335% for elongation rate. For the separation behavior adhesion method specimen, when tensile stress or displacement occurred, the Zero-Span tension occurrence did not follow, which resulted in that the bottom sheet layer and the top membrane layer did not simultaneously becoming damaged. When undergoing the top and bottom layers were separated through separation behavior due to lack of flexibility, the bottom layer began to damage at the primary stage, and with the allowed boundary the upper membrane layer began to display flexibility and showed continuous displaced resulting in secondary phase damaging.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.2
• /
• pp.31-37
• /
• 2015

Recently, mobile phones have become necessary tools for everyday life. In this study, a device that can serve as a separation between a touch panel and an LCD module in a mobile phone was devised for mass repair processes at a smaill business. We used a wire cutting method to separate the bonding plate area between the modules. The device is composed of DC motors and stepping motors that can deliver a precise cutting motion. The motor control system is connected by individual control modules to a CAN network. The developed device showed excellent performance at high temperature conditions.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.23 no.4
• /
• pp.403-407
• /
• 2010

Gecko adhesion system consists of beam-shaped seta and spatula which has the role of adhesive pad. In this paper, adhesion mechanism of gecko adhesion system is performed by using adhesive beam contact model. this model has a feature of non-uniform stress profile on the contact surface and adhesion/detachment mechanism is determined by the tensile stress of the contact region. a spatula tip pad has the role of reduction of maximum tensile stress and adhesive force is increased due to this effect. As for a reverse loading case, maximum compressive stress drops by the spatula effect and this cause unsymmetric loading conditions between adhesion and detachment forces. In this study, finite element method is used for the analysis of adhesive beam contact model and the results for spatula effect are presented.

• The Journal of the Acoustical Society of Korea
• /
• v.16 no.2
• /
• pp.26-30
• /
• 1997

In this paper, the thickness measurement method of adhesive layers of multilayers using power cepstrum signal processing technique has been proposed. The peak values for reflected signal from each layer have been separated by power cepstrum technique. Therefore, thickness of adhesive layers have been measured by the intervals of peak signal. In the experiment, the adhesive layers of 0.5mm-0.75mm thickness using epoxy(2-Ton and Plastic Steel Putty(A)) between the aluminum and the brass were formed. The adhesive layer thickness which is calculated with data of reflected signal by ultrasonic pulse-echo method was within error 1.34% of the measured values.

• Restorative Dentistry and Endodontics
• /
• v.34 no.2
• /
• pp.113-119
• /
• 2009

The purpose of this study was to compare the tensile bond strength of several self-adhesive resin cements bonded to dentin surfaces with different wet conditions. Three self-adhesive resin cements: Rely-X Unicem (3M ESPE, St. Paul, MN. USA). Embrace Wetbond (Pulpdent. Oakland. MA. USA). Maxcem (Kerr. Orange. CA. USA) were used. Extracted sixty human molars were used. Each self-adhesive resin cement was adhered to the dentin specimens (two rectangular sticks from each molar) in different wet conditions. Tensile bond strength were measured using universal testing machine (EZ Test. Shimadzu corporation. Kyoto. Japan) at a crosshead speed of 1.0mm/min. After the testing. bonding failures of specimens were observed by Operative microscope (OPMI pro, Carl Zeiss. Oberkochen, Germany). T-test was used to evaluate the effect of dentin surface wetness. One-way ANOVA test was used to evaluate the tensile bond strength of self-adhesive resin cements in the same condition. Scheffe's test was used for statistical analyzing at the 95% level of confidence. The result showed that wetness of dentin surface didn't affect tensile bond strength of self-adhesive resin cements and Maxcem showed the lowest tensile bond strength.

• Composites Research
• /
• v.20 no.5
• /
• pp.34-42
• /
• 2007

Strength and failure of adhesively bonded carbon composite-to-aluminum single-lap joints were studied by experiment. The main objective of this study is to investigate the effect of various parameters such as curing pressure for bonding, overlap lengths, and adherend thickness on the failure loads and modes of the bonded Joints with dissimilar materials. Experimental results show that the bonding pressure for composite-to-aluminum dissimilar materials should be 4 atm at the lowest. Failure load of the joints increases as the overlap length increases, but the strength (failure load divided by bonded area) decreases rapidly after the overlap width-to-length ratio is greater than 1. When the adherend thickness increase to double, bonding strength increase $12{\sim}55%$. Major failure mode of the joints is the delamination in the composite laminate and the location of delamination goes deeper into the laminates as the bonding pressure and overlap length increase.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.550-553
• /
• 2010

본 논문에서는 seta와 spatula로 구성된 게코(gecko) 접착 시스템의 해석을 위한 새로운 adhesive beam contact model을 제시한다. adhesive contact 해석에 있어서 기존의 JKR model은 nano pillar와 같은 형태의 접촉방식의 해석에는 매우 유용하지만, seta와 같이 보(beam)의 형상을 가지는 구조물의 접촉방식의 해석에는 부적합하다. 따라서 본 연구에서는 seta와 같은 보의 형상을 가지는 접촉 시스템의 해석을 위해 adhesive beam contact model을 제시하고, 유한요소 해석을 통하여 접촉면에서의 불균일한 응력분포 상태가 분리 메커니즘에 미치는 영향에 대한 해석 결과를 제시한다. 또한 spatula의 기하학적 형상과 보의 접촉각(contact angle)등이 seta adhesion system의 분리 메커니즘(detachment mechanism)에 미치는 영향에 대한 결과를 제시한다.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2001.11a
• /
• pp.118-123
• /
• 2001

항공기 운항 중에 손상된 부품의 교환이나 수리는 항공기 운항 시 안전 유지와 고가의 항공기 수명연장을 위하여 필수적이다. 여러 가지 손상이나 고장 중에서 균열은 기계적 체결요소(리벳, 볼트 등)나 패칭에 의하여 효과적으로 보수될 수 있다. 항공기 동체 보수 시 접착제 접합을 사용한 복합재료 패칭은 하부구조에 손상이 없이 균열진전을 줄일 수 있고 구멍의 생성으로 인한 응력 집중을 제거할 수 있으며 접합된 면을 외부로부터 차단시켜 부식을 방지하는 효과가 있어 많이 사용된다 특히 고강도 복합재료와 접착제의 개발로 인하여 손상된 구조의 보수를 위한 복합재료 패칭의 사용은 더욱 증가되고 있다.(중략)

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.8 no.1
• /
• pp.15-22
• /
• 2002

We received 2 types flexible packaging films from two companies that laminated PET $16{\mu}m/dry$ lamination/aluminium foil $7{\mu}m/dry$ lamination/CPP $80{\mu}m$ films. For the reason of hot sealing's trouble through filling process, We separated each layer and compared thicks, film types and tested IR, DSC and sensory test. At the result, one sample's thick is different but film types is same between samples. Optimum hot-sealing conditions between two samples is $195^{\circ}C\;and\;210^{\circ}C$. The difference is $15^{\circ}C$. According to test of direct filling packaging process by four face fluid filling machine, two sample's sealing strength of hot-sealing is $4.76kg/cm2/15mm$(sample of optimum hot-sealing condition is $195^{\circ}C$) and $3.84kg/cm2/15mm(210^{\circ}C)$.

• The Journal of Korean Academy of Prosthodontics
• /
• v.48 no.3
• /
• pp.194-201
• /
• 2010

Purpose: The purpose was to compare the marginal fidelity and the fracture resistance of the zirconia crowns according to the various coping designs with different thicknesses and cement types. Materials and methods: Zirconia copings were designed and fabricated with various thicknesses using the CAD/CAM system (Everest, KaVo Dental GmbH, Biberach., Germany). Eighty zirconia copings were divided into 4 groups (Group I: even 0.3 mm thickness, Group II: 0.3 mm thickness on the buccal surface and the buccal half of occlusal surface and the 0.6 mm thickness on the lingual surface and the lingual half of occlusal surface, Group III: even 0.6 mm thickness, Group IV: 0.6 mm thickness on the buccal surface and the buccal half of occlusal surface and the 1.0 mm thickness on the lingual surface and the lingual half of occlusal surface) of 20. By using a putty index, zirconia crowns with the same size and contour were fabricated. Each group was divided into two subgroups by type of cement: Cavitec$^{(R)}$ (Kerr Co, USA) and Panavia-$F^{(R)}$ (Kuraray Medical Inc, Japan). After the cementation of the crowns with a static load compressor, the marginal fidelity of the zirconia crowns were measured at margins on the buccal, lingual, mesial and distal surfaces, using a microscope of microhardness tester (Matsuzawa, MXT-70, Japan, ${\times}100$). The fracture resistance of each crown was measured using a universal testing machine (Z020, Zwick, Germany) at a crosshead speed of 1 mm/min. The results were analyzed statistically by the two-way ANOVA and oneway ANOVA and Duncan's multiple range test at $\alpha$=.05. Results: Group I and III showed the smallest marginal fidelity, while group II demonstrated the largest value in Cavitec$^{(R)}$ subgroup (P<.05). For fracture resistance, group III and IV were significantly higher than group I and II in Cavitec$^{(R)}$ subgroup (P<.05). The fracture resistances of Panavia-$F^{(R)}$ subgroup were not significantly different among the groups (P>.05). Panavia-$F^{(R)}$ subgroup showed significantly higher fracture resistance than Cavitec$^{(R)}$ subgroup in group I and II (P<.05). Conclusion: Within the limitation of this study, considering fracture resistance or marginal fidelity and esthetics, a functional ceramic substructure design of the coping with slim visible surface can be used for esthetic purposes, or a thick invisible surface to support the veneering ceramic can be used depending on the priority.