• Journal of Korean Tunnelling and Underground Space Association
• /
• v.15 no.3
• /
• pp.333-344
• /
• 2013

This paper discussed about the effect of permeability reduction of the jointed rock mass in the vicinity of a tunnel which is one of the reasons making large difference between the estimated ground-water inflow rate and the measured value. Current practice assumes that the jointed rock mass around a tunnel is a homogeneous, isotropic porous medium with constant permeability. However, in actual condition the permeability of a jointed rock mass varies with the change of effective stress condition around a tunnel, and in turn effective stress condition is affected by the ground water flow in the jointed rock mass around the tunnel. In short time after tunnel excavation, large increase of effective tangential stress around a tunnel due to stress concentration and pore-water pressure drop, and consequently large joint closure followed by significant permeability reduction of jointed rock mass in the vicinity of a tunnel takes place. A significant pore-water pressure drop takes place across this ring zone in the vicinity of a tunnel, and the actual pore-water pressure distribution around a tunnel shows large difference from the value estimated by an analytical solution assuming the jointed rock mass around the tunnel as a homogeneous, isotropic medium. This paper presents the analytical solution estimating pore-water pressure distribution and ground-water inflow rate into a tunnel based on the concept of hydro-mechanically coupled behavior of a jointed rock mass and the solution is verified by numerical analysis.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.10
• /
• pp.17-30
• /
• 2009

Underground construction such as tunneling can induce damages on the surrounding rock mass, due to the stress concentration of in situ stresses and excessive energy input during construction sequence, such as blasting. The developed damage on the rock mass can have substantial influence on the mechanical and hydraulic behaviors of the rock masses around a tunnel. In this study, investigation on the generation of damage around an opening in a jointed rock model under biaxial compression condition was conducted. The joint dip angles employed are 30, 45, and 60 degrees to the horizontal, and the synthetic rock mass was made using early strength cement and water. From the biaxial compression test, initiation and propagation of tensile cracks at norm to the joint angle were found. The propagated tensile cracks eventually developed rock blocks, which were dislodged from the rock mass. Furthermore, the propagation process of the tensile cracks varies with joint angle: lower joint angle model shows more stable and progressive tensile crack propagation. The development of the tensile crack can be explained under the hypothesis that the rock segment encompassed by the joint set is subjected to the developing moment, which can be induced by the geometric irregularity around the opening in the rock model. The experiment results were simulated by using discrete element method PFC 2D. From the simulation, as has been observed from the test, a rock mass with lower joint angle produces wider damage region and rock block by tensile cracks. In addition, a rock model with lower joint angle shows progressive tensile cracks generation around the opening from the investigation of the interacted tensile cracks.

• The Journal of Engineering Geology
• /
• v.18 no.2
• /
• pp.159-166
• /
• 2008

We have a question about the changing possibility of orientation of discontinuities through the depth of under-ground. To know this, the data from Honam coalfield composed of shale, sandstone and coal and Suwon area which crops out mica schist, were analyzed the discontinuities measured by BIPS and Televiewer. In Honam coalfield the orientations of joints are changed at 30-40 m depth of underground and in Suwon area they are changed around 20 m depth. To compared the results from Honanam coalfield and Suwon area, there are different rock type and geologic structure. However, the attitude of the discontinuities are changing at 20-30 m depth of underground.

• Journal of the Speleological Society of Korea
• /
• no.67
• /
• pp.21-34
• /
• 2005

Jeomal Cave consists of limestone. Soil distribution is very different from mountain area to piedmont area. The Cave developed in a part of the fault valley. The joints controls the low level stream orders in the cave. in this area the geological structure is close relate to the underground water flow. It is certain that the distribution of the clay came from the surface.

• The Journal of Engineering Geology
• /
• v.19 no.4
• /
• pp.517-528
• /
• 2009

Statistical analyses of cut-slope stability were performed over approximately 5.7 km section along the National road No. 25, which cross-cuts in NW-SE direction the Cheongwon and Boeun-Gun area, Chungbuk. A measure of slope-stability was established by using direct reinforcement and indirect protection methods in whole section. Orientations(dip/dip direction) of the slopes, foliations(bedding), cleavages and joints were measured in total of 30 slope sites. The results analyzed using stereographic projection indicate that major directions of the slopes come out predominantly in three directions: 1) $58^{\circ}/095^{\circ}$, 2) $60^{\circ}/296^{\circ}$ and 3) $59^{\circ}/212^{\circ}$. In analyses of dip direction and frequency of cut-slopes established by reinforcement and protection methods, slopes with dip direction of $80-120^{\circ}$ and $280-320^{\circ}$ mostly occur. However, slopes with dip direction of $0-80^{\circ}$(N and NW) and $120-160^{\circ}$(SE) are not distributed in the study area. Failure aspects were analyzed for three major directions of the slopes, respectively. The results of failure aspects analyzed indicate that slopes in the study area could generate various failures as the results of intersection and/or intersection combination among joints, foliations(bedding) and cleavages. However, possibility of failure in a slope of major direction No. 3 is statistically very low because of low frequency in total number of slopes with the direction and of formation of small scale-slopes geographically, although the slope might generate all aspects of failure-modes.

• Tunnel and Underground Space
• /
• v.22 no.6
• /
• pp.393-402
• /
• 2012

A behavior of ridge-cut rock slope had been monitored by installing inclinometers and regional slope movement toward rear side of cut face was detected. To delineate the governing factors of slope behavior, especially backward slip of ridge-cut slope, petrographic characteristics of rock cores obtained from four drilled boreholes had been examined. BIPS images inside boreholes had been acquired and structural characteristics of slope rock had been studied. Mechanical properties of discontinuity planes distributed in the drilled core had been measured and the shear strength of coal seam imbedded-discontinuity planes also had been obtained by performing the direct shear test. Monitoring results of slope behavior had been analyzed by comprehensibly considering both the mechanical and structural characteristics of slope rock and coal seam-imbedded discontinuity planes, and the potential governance of coal seam and clay minerals embedded in the joint plane on the regional slope behavior has been also identified.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.10
• /
• pp.97-107
• /
• 2007

Accurate evaluation of the slope stability by assuming failure block as the entire slope is considered to be apposite for the small scale slope, whereas it is not the case for the large scale slope. Hence, appropriate estimation of a failure block size is required since the safety factor and the joint strength parameters are the function of the failure block size. In this paper, the size of failure block was investigated by generating 3-dimensional rock joint system based on statistical data of joints obtained from research slope, such as joint orientation, spacing and 3-dimensional joint intensity. The result indicates that 33 potential failure blocks exist in research slope, as large as 1.4 meters at least and 38.7 meters at most, and average block height is 15.2 meters. In addition, the data obtained from 3 dimensional joint system were directly applicable to the probability analysis and 2 and 3 dimensional discontinuity analysis.

• Tunnel and Underground Space
• /
• v.22 no.1
• /
• pp.43-53
• /
• 2012

Stability of cut-slope, the orientation and dimension of which are gradually changed, has been analyzed by employing the cross-section method capable of comprehensibly considering the lithological, structural and mechanical characteristics of slope rock. Lithological fragility is investigated by inspecting the drilled core logs and BIPS image has been taken to delineate the rock structure. Engineering properties of drilled-core including the joint shear strength have been also measured. Potential failure modes of cut-slope and failure-induced joints are identified by performing the stereographic projection analysis. Traces of potential failure-induced joints are drawn on the cross-section which depicts the excavated geometry of cut-slope. Considering the distribution of potential plane failure-induced joint traces blocks of plane failure mode are hypothetically formed. The stabilities and required reinforcements of plane failure blocks located at the different excavation depth have been calculated to confirm the applicability of the cross-section method for the optimum cut-slope design.

• Tunnel and Underground Space
• /
• v.8 no.3
• /
• pp.234-248
• /
• 1998

This paper presents a new constitutive model for numerical modeling the shear behaviour of rough rock joints. The model incorporates the dilatancy of joints on the basis of elasto-plastic theory. Barton's empirical shear strength formular are adopted in the formulation process. The mobilized JRC concept is evoked to address the shear strength hardening and sofrening phenomena. The mobilized JRC in the pre- and post-peak range is approximated by assuming that the variation of JRC is a function of tangential plastic work. Discrete finite joint element is used to implement the proposed constitutive model. The model is validated by the numerical direct shear test on a single joint which is subjected to different boundary conditions. The test results are in good agreement with the experimental observations reported by other authors. The numerical tests also exhibit that the proposed model can simulate the salient features envisaged in the behaviour of rough rock joints.

• Tunnel and Underground Space
• /
• v.26 no.6
• /
• pp.475-483
• /
• 2016

A numerical analysis model capable of predicting the shape, the size and the potentiality of collapse of tetrahedral blocks considering the persistence obtained from the field survey of joint distribution around the underground excavation surface has been developed. Numerical functions of analyzing both the exposed trace distribution on the excavation surface and the formation of tetrahedral block controlled by the extent of joint surface have been established and linked to the previously developed three dimensional deterministic block analysis model. To illustrate the reliability of advanced numerical model the case of underground excavation in which the collapse of rock block had practically taken place was studied. Representative orientations of joint sets was determined based on the joint distribution pattern observed on the excavation surfaces. The formation of block on the roof of underground opening was analyzed to unveil the potential tetrahedral block the shape of which was very similar to the collapsed rock block. Mechanisms of collapse process has been also analyzed by considering the three dimensional shape of tetrahedral block.