• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.1
• /
• pp.1-12
• /
• 1992

Generally, laser machines with high generated power can be developed by means of enhancing their mean power, since the enhancement of mean power exerts an influence on peripheral parameters and machining performance. In this research, we evaluate the various machining properties by the use of two machines which bear different mean power each other, so that we may study various effects of the enhancement of mean power. As a result, when the mean power comes to be enhanced to 75%, we obtain the increase of output energy up to 69% and of peak power more than 95%, and also obtain almost twice of the cutting speed. Moreover we find the fact that if the test pieces have enough thickness in contrast with output energy, the pulse frequency moves toward the frequency bandwidth which takes proportion to the cutting speed mas well as to the amount of material removal per unit time. In addition it is finally obtained that the laser machine with high output power yields small taper degrees at kerf parts, while it has large cutting widiths and dross lengths.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.6 no.3
• /
• pp.152-155
• /
• 2013

In this paper, the reduction of the figure of merit depending on the increased spill-over when the parabolic reflector is cut off partially for low-profile configuration in the satellite broadcast receiving antenna is analyzed. Also for the accurate analysis and simulation, it is considered that the noise temperature is increased due to the effect of ground thermal noise toword the sidelobes and back lobes when the antenna is tracked from $0^{\circ}$ to $60^{\circ}$ in elevation angle, and that the total noise temperature is increased because to the noise figure of LNA. As the results, noise temperature is increased up to about 15K and G/T ratio is decreased to about 2.5dB, when the reflector is cut 35% off partially.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.4
• /
• pp.611-617
• /
• 1989

A jet cutting system is a new concept of cutting device wihch requires high pressure up to thousands of atmospheric pressure. The use of water as a cutting medium brings in many of working advantages such as no dust, no gas, and no thermal distortion. And an introduction of abrasives into the water jet flow increases signigicantly cutting abilities and improves cutting performance. Cutting with abrasive water jet involves many operating variables, including design of the cutting system. For efficient cutting, the operating parameters have to chosen properly. In spite of several attempts to develop the cutting model theoretically, all of the optimization of the operating parameters is based upon exerimental results of each jet cutting system. In this paper, the effect of the parameters was measured and analysed in terms of pressure, abrasive, and transverse rate of a workpiece. Most of all, sufficient feeding of abrasives is the most important factor for efficient cutting performance.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.2
• /
• pp.443-448
• /
• 2010

Rapid advance in information technology requires high performance devices with compact size. Integrated multi-layer electronic element with different functions enables those compact devices to possess various performances and powerful capabilities. In mass production, the multi-layer electronic element is manufactured as a bulk type with a large number of parts for productivity. However, this may cause the electronic part to be damaged in the cutting process of the bulk elements to separate into each part. Therefore the cutting performance of multi-layer element bulk is playing an important role in the view of production efficiency. This study focuses on the cutting characteristics of multi-layer electronic elements. In order to increase the efficiency, the vibration cutting method was applied to the blade cutting machine. Flexure hinge structure, which is an physical amplifier of increasing displacement, was attached to the vibration cutting device for machining efficiency. The behaviors of flexure hinge were modeled with Lagrange equation and simulated with finite element method (FEM). Performance of hinge structure was verified by experimental modal analysis (EMA) for hinge structure to be tuned to the specific mode of vibrations. Cutting experiments of multi-layer elements were conducted with the proposed vibrating cutting module, and the characteristics was analyzed.

• Journal of Bio-Environment Control
• /
• v.26 no.4
• /
• pp.242-248
• /
• 2017

This study was conducted to develop a cylindrical paperpot manufacturing equipment which is capable of continuously producing paperpots with a constant size. The equipment consists of the soil supply part, the paper supply part, the pot manufacturing part, the paperpot cutting part and its process for manufacturing paperpot from the soil supply to the paperpot cutting is continuously performed. As a result of the performance test using this equipment, we suggest that the optimal moisture content and injection pressure to supply soil are 50%~60%, and 0.5 Mpa respectively. Moreover the appropriate temperature for adhesive strength is $150{\sim}160^{\circ}C$ taking into account the performance of device and adhesion time. Also, considering the cutting speed and safety, it is appropriate to adopt a straight blade having a clean plan at a minimum angle of $30^{\circ}$. In addition, the manufacturing capacity of the developed equipment was 3300 pots per hour.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.4B
• /
• pp.316-323
• /
• 2002

In this paper, we analyze the call control scheme that is using buffer at new call and handoff call for non-uniform traffic load distribution, the multiple cell environments and the multiple types of services such as voice and data service. Considering the facts, the call admission control method using the effective bandwidth concept is employed in this paper, The bandwidth for a new call and a handoff call is allocated by the number of mobile station and dynamically assigned by taking account of the blocking rate of new calls and the dropping rate of handoff calls. The call control procedure is experimented through a simulation study by dynamically the bandwidth to new and handoff calls based on the blocking rate and the dropping rate. The results show our call control scheme can get a good quality of service for mobile users.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.6
• /
• pp.83-90
• /
• 2018

This paper introduces a innovative diamond wire saw cutting technology and its experimental verification that can be utilized for cutting heavy structures. While conventional diamond wire saw cutting technologies such as water cooled cutting method and dry cutting method cause severe environmental problems due to generating massive concrete sludge or dust scattering, the proposed method can eliminate those problems considerably. Through extensive experiments using heavy structure test bed and real bridge pier structure, comprehensive analysis and comparative evaluation about various cutting methods were performed. As a result, the innovative diamond wire saw cutting method could achieve a similar cutting and cooling performance to the water cooled cutting method without generating concrete sludge and it showed an improved cutting and cooling performance to the dry cutting method without dust scattering. Consequently it is confirmed that the suggested cutting technology can be a promising environment-friendly alternative in the field of heavy structure dismantling.

• Explosives and Blasting
• /
• v.20 no.3
• /
• pp.15-23
• /
• 2002

철골구조물은 일반 철근 콘크리트 구조와는 달리 단순히 천공을 하고 폭약을 장약하여 기폭시키는 방법으로는 해체 또는 절단이 어렵다. 국내의 경우 최근 철골 구조로 건축되는 강교와 건축물 등이 증가하는 추세이며, 내구연한이 다하거나 구조적 결함으로 인하여 해체 대상으로 지목되는 철골구조물에 대해서는 특수한 형태의 해체 기술을 필요로 한다. 1997년 이후 국내에 철골구조물의 발파해체를 위하여 성형폭약에 의한 폭발절단기술에 관한 연구가 소개된 이후로 폭발절단력에 미치는 성형폭약의 라이너(Liner), 폭약의 종류, 형상 및 이격거리(Stand-off distance) 등에 대한 연구가 활발히 이루어졌으며, 또한 국산화를 위한 기초적인 설계변수에 관한 연구 등이 보고 된 바 있다. 현재 성형폭약의 사용범위가 철골구조물의 절단해체 뿐만 아니라 긴급구조를 필요로 하는 특수한 용도나 군사폭약의 해체, 항공산업 등 그 적용범위가 확대되고 있는 실정이다. 그러나, 성형폭약의 성능 향상 및 품질 보증을 위한 체계적인 설계 변수의 검토 설정에 관한 연구와 산업f'의 적용을 위한 구체적인 결과는 보고 된 바 없는 실정이다. 그래서, 보다 체계적인 현장 적용 시험 등에 대한 연구가 효율적으로 진행될 경우 국내 고유 기술에 의한 철구조물의 절단 및 해체공법에 획기적인 변화를 가져올 수 있을 것으로 기대된다. 따라서, 본 연구에서는 국산화되어 현장에 적용되고 있는 성형폭약 HAKO 제품을 기준으로 이미 국내에 알려진 성형폭약과 비교 분석하였다. 또한 보다 효율적인 산업계의 적용을 위한 각종 시험 결과 및 국산화 현황과 향후 활용 방안 등에 대하여 소개하고자 한다.

• Journal of the Korean Data and Information Science Society
• /
• v.20 no.3
• /
• pp.467-474
• /
• 2009

There are many situations arising in reliability engineering and biomedical science where failure of a subsystem increases the failure rate of other subsystem under shared load models. In this paper, the maximum likelihood estimates and the modified maximum likelihood estimates of mean time to failure and reliability function for shared load model with guarantee time are obtained by using censored system life data. Some illustrative examples are included.

• Proceedings of the Korean Society of Disaster Information Conference
• /
• 2017.11a
• /
• pp.197-198
• /
• 2017

인공재해와 자연재해로 인해 발생하는 비정상 하중에 의해 국부손상이 발생된 철골 교량 구조물은 추가적인 2차 붕괴의 위험요소들을 내재하고 있어 신속한 전면 해체가 요구된다. 본 시공 사례는 건설실패와 태풍 및 지진으로 국부손상이 발생된 철골 트러스 구조의 교량의 긴급해체를 위해 발파해체 공법을 적용한 사례이다. 철골 부재의 절단을 위해 성형폭약이 필요하지만 현지에서 수급이 불가능한 상태이기 때문에 장약용기를 직접 제작하고 에멀젼 폭약을 충전하여 만든 성형폭약을 이용하여 발파해체에 적용하였다. 직접 제작한 성형폭약을 이용하여 발파해체한 결과 철골 부재가 정확히 절단되면서 교량의 중앙부가 수직자유낙하하고, 교량의 양 끝단은 지지부를 중심으로 회전낙하 하였다. 또한 존치 구조물 및 주변에 피해가 발생하지 않았으며, 발파 후 파쇄 상태는 매우 양호하였다. 이로 인해 직접 제작한 성형폭약의 절단 성능을 확인할 수 있었으며, 신속하고 안전하게 국부손상이 발생된 구조물을 해체하였다.