• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.6 no.2
• /
• pp.11-18
• /
• 1995

The goal of this research is to get a measuring system for absorption characteristics of electromagnetic wave absorbers in fernite type which are flat, grid-type and special type, etc. It is, however, very difficult to measure the absorption characteristics in as low frequency as 30 MHz. To solve the problem, therefore, we propose a standing wave method and a measurement method in time domain using paralledl striplines, construct the measuring system, and measure the charac- teristics of ferrite microwave absorbers in grid type using the proposed measuring system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.1
• /
• pp.1-15
• /
• 2015

In this invited paper, the authors give an overview of the new design technology for a metallic backplane-less metamaterial(MM) absorber and discuss a selection of examples. In contrast to a common MM absorber structure, the metallic pattern layer of the presented structure is placed facing toward the incident wave propagation direction to reduce the radar cross section(RCS) due to the metallic pattern itself at frequencies other than the targeted absorption frequency bands. The ability of the MM backplane-less absorber to exhibit broadband absorption performance and irregular surface applications will be discussed.

• Composites Research
• /
• v.17 no.5
• /
• pp.68-77
• /
• 2004

The electromagnetic (EM) absorption or shielding characteristics of a material is an important issue not only for military purpose but also for commercial purposes such as radar, electric or telecommunication devices. In order to design the effective electromagnetic wave absorber, the electromagnetic characteristics of the constituents of the material should be available in target frequency band. Also, it must be possible to predict the electromagnetic properties of absorbers with respect to the content of lossy ingredients. In this study, the dielectric properties of unsaturated polyester resins containing nano-size conductive carbon black powder were measured with a free space method in the X-band frequency range and analyzed with respect to the content of carbon black. Finally, the method for estimating the dielectric properties of polymeric resin containing conductive carbon black with respect to the EM frequency was developed and verified.

• Journal of the Korean Magnetics Society
• /
• v.4 no.3
• /
• pp.285-292
• /
• 1994

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.4 no.2
• /
• pp.17-23
• /
• 1993

This study aims to measure the reflection loss and the material constants of the fabricated samples for electromagnectic wave absorber by using $20 mm\phi$ coaxial tube with the endshort-type. The authors have established the extraction algorithm of material constants by one port method, and proved that the results of the experiments were in agreement with the calculated ones. On the basis of the above results, the validity of the proposed measuring method is confirmed. This measurement method could be used effectively for the design of microwave absorber and for its evalustion.

• Journal of the Korean Magnetics Society
• /
• v.15 no.5
• /
• pp.282-286
• /
• 2005

Ni-Cu-Zn ferrites were prepared by the co-precipitation and ferrite microwave absorbers on low temperature sintering were investigated in this work. The properties of its microwave absorbing and physical were analyzed into variations of Ni addition, calcination temperature, sintering temperature. From the analysis of X-ray diffraction patterns, we can see that all the particles have only a single phase spinel structure. In addition, the powders particle size distribution obtained the nano size. By increasing the Ni additive, the permeability of the powders was decreased and the loss factor increased at sintering temperature $1100^{\circ}C$. Also, we considered that it can used high frequency rage. We found that the $(Ni_{0.7}Cu_{0.2}Zn_{0.1}O)_{1.02}(Fe_{2}O_3)_{0.98}$ appeared microwave absorbing properties better than other composition.

• Journal of the Korean Magnetics Society
• /
• v.18 no.3
• /
• pp.120-125
• /
• 2008

In this study, NiCoZn ferrites with the variation of sintering temperature and chemical composition were prepared by the coprecipitation. Microstructures Crystal structure of NiCoZn ferrites were analyzed by XRD and their electric magnetic characteristics were analyzed by LCR meter and their morphology observed by SEM. We identified that these powders have a typical NiCoZn spinel structure and nanoparticles average size of 40 nm. The impurity, the initial permeability and the Q factor value are the lowest of sintered NiCoZn ferrite at $1250^{\circ}C$. Also, we measured S-parameter for $(Ni_{0.4}Co_{0.1}Zn_{0.5})Fe_2O_4$ which showed a maximum reflection loss of -3.1 dB at 6 GHz for the 2 mm thick sample. From this result, we found that the NiCoZn ferrite can be used in ferrite microwave-absorbing application at a higher frequency region (> 6 GHz).

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.06a
• /
• pp.95-98
• /
• 2007

In this paper, we make an analysis of electromagnetic wave absorption properties of $TiO_2$ in W-band. Therefore, we fabricated some samples in different composition ratio of $TiO_2$ and CPE. And the material properties of samples are calculated from S-parameter of samples using $\ell-2\ell$ method. We analyze absorption properties and complex relative permittivitis of samples. As a result, it has verified that absorption properties of sample containing $TiO_2:CPE=70:30wt.%$ have been excelled in W-band.

• Proceedings of the Korean Magnestics Society Conference
• /
• 1998.10a
• /
• pp.112-113
• /
• 1998

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.3
• /
• pp.440-448
• /
• 1999

This paper describes a full wave analysis of the scattering from electromagnetic absorbers which can be approximated as infinite periodic structure using hybrid finite element method. By introducing fictitious boundaries, equivalent finite region is defined and proper boundary conditions of each boundary are obtained by Floquet theorem. Since higher-order Floquet modes are employed, the method presented in this paper can be readily applied to the periodic structure haying a relatively long period. To reduce difficulty in evaluating the surface integral, the normal component to the surface were represented with the tangential component to the surface. Comparisons of calculated results with analytical or published ones show the validation of the method.