• The Journal of Korean Academy of Prosthodontics
• /
• v.60 no.2
• /
• pp.135-142
• /
• 2022

Purpose. This study aims to evaluate the combined effect of reduced thickness in different regions on the fracture resistance of monolithic zirconia crowns. Materials and methods. Seven nickel-chromium dies were generated from a 3D model of mandibular first molar using the digital scanner with the following geometries: 1.5 mm occlusal reduction, 1.0 mm deep chamfer. Based on the abutment model, Zirconia blocks (Luxen Zirconia) were selected to fabricate Sixty-three zirconia crowns with occlusal thicknesses of 0.3 mm, 0.5 mm, and 1.5 mm, and different axial thicknesses of 0.3 mm, 0.5 mm, and 1.0 mm. All crowns were cemented by resin cement. Next, the crowns were subjected to load-to-fracture test until fracture using an electronic universal testing machine. In addition, fracture patterns were observed with a scanning electron microscope (SEM). Two-way ANOVA and the Tuckey HSD test for post hoc analysis were used for statistical analysis (P < .05). Results. The mean values of fracture resistancerecorded was higher than the average biting force in the posterior region. The two-way ANOVA showed that the occlusal and axial thickness affected the fracture resistance significantly (P < .05). However, the effect of axial thickness on fracture resistance did not show a statistical difference when thicker than 0.5 mm. The observed failure modes were partial or complete fracture depending on the severity of crack propagation. Conclusion. Within the limitations of the present study, the CAD-CAM monolithic zirconia crown with extremely reduced thickness showed adequate fracture resistance to withstand occlusal load in molar regions. In addition, both occlusal and axial thickness affected the fracture resistance of the zirconia crown and showed different results as combined.

• Food Science and Industry
• /
• v.55 no.2
• /
• pp.188-202
• /
• 2022

In the insect industry, as the scope of application of insects is expanded from pet insects and natural enemies to feed, edible and medicinal insects, the demand for quality control of insect raw materials is increasing, and interest in securing the safety of insect products is increasing. In the process of expanding the industrial scale, controlling the temperature and humidity and air quality in the insect breeding room and preventing the spread of pathogens and other pollutants are important success factors. It requires a controlled environment under the operating system. European commercial insect breeding facilities have attracted considerable investor interest, and insect companies are building large-scale production facilities, which became possible after the EU approved the use of insect protein as feedstock for fish farming in July 2017. Other fields, such as food and medicine, have also accelerated the application of cutting-edge technology. In the future, the global insect industry will purchase eggs or small larvae from suppliers and a system that focuses on the larval fattening, i.e., production raw material, until the insects mature, and a system that handles the entire production process from egg laying, harvesting, and initial pre-treatment of larvae., increasingly subdivided into large-scale production systems that cover all stages of insect larvae production and further processing steps such as milling, fat removal and protein or fat fractionation. In Korea, research and development of insect smart factory farms using artificial intelligence and ICT is accelerating, so insects can be used as carbon-free materials in secondary industries such as natural plastics or natural molding materials as well as existing feed and food. A Korean-style customized breeding system for shortening the breeding period or enhancing functionality is expected to be developed soon.

• Journal of Navigation and Port Research
• /
• v.46 no.3
• /
• pp.179-190
• /
• 2022

In this study, we investigated the characteristic impedance and bandwidth of CPW3DCS (coplanar waveguide employing periodic 3D coupling structures), and examined its potential for the development of a marine radio communication FISoC (fully-integrated system on chip) semiconductor device. To extract bandwidth and characteristic impedance of the CPW3DC, we induced a measurement-based equation reflecting measured insertion loss, and compared the measured results of the propagation constant β and characteristic impedance with the measured ones. According to the results of the comparison, the calculated results show a good agreement with the measured ones. Concretely, the propagation constant β and characteristic impedance exhibited an maximum error of 3.9% and 6.4%, respectively. According to the results of this study, in a range of LT = 30 ~ 150 ㎛ for the length of periodic structures, the CPW3DC exhibited a passband characteristic of 121 GHz, and a very small dependency of characteristic impedance on frequency. We could realize a low impedance transmission line with a characteristic impedance lower than 20 Ω by using CPW3DCS with a line width of 20 ㎛, which was highly reduced, compared with a 3mm line width of conventional transmission line with the same impedance. The characteristic impedance was easily adjusted by changing LT. The above results indicate that the CPW3DC can be usefully used for the development of a wireless communication FISoC (fully-integrated system on chip) semiconductor device. This is the first report of a study on the bandwidth of the CPW3DC.

• Korean Journal of Heritage: History & Science
• /
• v.55 no.2
• /
• pp.66-79
• /
• 2022

In the mid-Kofun period, the technology employed in the southern part of the Korean Peninsula had reached the Japanese archipelago, and a Japanese-style unglazed earthenware called Sueki was produced. During the early period of the spread of technology, regional elements from all over the Korean Peninsula remained strong, with production on the Japanese archipelago carried out only in very limited regions. After that, production in all parts of the archipelago began gradually. The Sueki culture was introduced to the Japanese archipelago with the technology of the Korean Peninsula; however, many excavations have been reported in the Korean Peninsula(these excavations are even called Suekitype). Many of these excavations were conducted in Jeolla-do, Yeongnam, and the Yeongsan River basin. As revealed in previous studies, however, many imitations were excavated around Jeolla-do, while Sueki of the Japanese archipelago were excavated from tombs in the Yeongnam area. The excavation period was generally from the late 5^th century to the early 6^th century(especially from the TK23 to MT15 stage), which is fundamentally different from that of Jeolla-do. Regarding the locations where Sueki were excavated, the majority were found in the tombs of local authorities. They were rarely excavated from the tombs of the royal people. Furthermore, there is no evidence of special meaning given to funeral ceremonies or Sueki in the Japanese archipelago form; therefore, most of them are thought to have been treated the same as unglazed earthenware. Considering the tombs as a whole, influential people(groups, families, and forces) were not only connected to certain areas of the Gaya region but also had complex and larger relationships. In other words, the Sueki excavated from the Yeongnam area may reflect the rise and fall of the forces in each Gaya region and the changes of the Yeongnam period. The role of negotiation and exchange can be seen not only from the fact that influential people in the central government of the Gaya region were involved but also from the existence of areas(groups, families, forces) discovered in the Gaya region indicating mutual relationships.

• The Journal of Engineering Geology
• /
• v.31 no.4
• /
• pp.621-630
• /
• 2021

This study evaluated cracks and climate monitoring in Ipseok-dae columnar joints and Jigong Neodeol rock blocks in Mudeungsan National Park. The rocks' state of cracking and their surface temperatures were measured alongside air temperature, relative humidity, and wind velocity. The maximum crack behavior in Ipseok-dae was 0.367 mm at one point, and showed a slight tendency at other points. One in Jigong Neodeol was within 0.15 mm and showed a stable state with little change. The surface temperature of the Ipseok-dae columnar joints was higher on the side exposed to sunlight than on the shaded side. All blocks of Jigong Neodeol rock showed similar temperatures. The air temperature showed a similar distribution for both rock types. The air temperature showed a similar distribution for both Ipseok-dae and Jigong Neodeol. The relative humidity was mostly between 20% and 60% in Ipseok-dae and was between 20 and 70% in Jigong Neodeol. Both areas had low wind speeds, with maxima of 5 m/s in Ipseok-dae and 3 m/s in Jigong Neodeol. As a result, it is evaluated that crack behavior in Ipseok-dae columnar joints and Jigong Neodeol rock blocks have maintained a very stable state so far. The surface temperature, temperature, relative humidity, and wind velocity of the two areas showed small difference depending on the season, indicating that they were affected to some extent by the season. From a long-term perspective, this can continuously affect the deformation of the Ipseok-dae columnar joints or Jigong Neodeol rock blocks. Therefore, in order to accurately evaluate their stability, it is considered that the current microscopic delamination and exfoliation or the propagation and expansion of cracks should be continuously measured.

• Journal of the Korea Institute of Building Construction
• /
• v.22 no.6
• /
• pp.651-662
• /
• 2022

The electrochemical impedance spectroscopy(EIS) method was used to evaluate the concrete deterioration process related to chloride-induced steel corrosion with various corrosion levels(initiation, rust propagation and acceleration periods). The impressed current technique, with four total current levels of 0C, 13C, 65C and 130C, was used to accelerate steel corrosion in concrete cylinder samples with w/c ratio of 0.4, 0.5, and 0.6, immersed in a 0.5M NaCl solution. A series of EIS measurements was performed to monitor concrete deterioration during the accelerated corrosion test in this study. Some critical parameters of the equivalent circuit were obtained through the EIS analysis. It was observed that the charge transfer resistance(R_c) dropped sharply as the impressed current increased from 0C to 13C, indicating a value of approximately 10kΩcm². However, the sensitivity of R_c significantly decreased when the impressed current was further increased from 13C to 130C after corrosion of steel had been initiated. Meanwhile, the double-layer capacitance value(C_dl) linearly increased from 50×10^-6μF/cm² to 250×10^-6μF/cm² as the impressed current in creased from 0C to 130C. The results in this study showed that monitoring C_dl is an effective measurement parameter for evaluating the progress of internal concrete damages(de-bonding between steel and concrete, micro-cracks, and surface-breaking cracks) induced by steel corrosion. The findings of this study provide a fundamental basis for developing an embedded sensor and signal interpretation method for monitoring concrete deterioration due to steel corrosion at various corrosion levels.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.49 no.2
• /
• pp.206-216
• /
• 2022

This study aimed to investigate the frequency of dental visits after coronavirus disease 2019 (COVID-19) in children and adolescents in comparison to that of adults. The data on the number of dental visits on the basis of different classification and treatment codes for all the age groups were provided by the Health Insurance Review and Assessment Service from January 2017 to December 2020. To reduce the impact of the population change, dental visits per 1000 people was used. After the start of the pandemic, dental visits per 1000 people decreased in all age groups when analyzed for the diseases of pulp and periapical tissues classification code and dental visits per 1000 people decreased over 5 years age groups when analyzed for the pulp treatment code. Regarding the restorative treatment code, visits in the 0 - 19 years age group decreased after the pandemic. Based on the comparison of the number of confirmed COVID-19 cases to that of monthly dental visits by treatment codes, the change rate of pulp and restorative treatments gradually decreased after the waves of the pandemic in February and August 2020 in Korea. Furthermore, dental visits per 1000 people for gingivitis and periodontal disease classification code increased after the pandemic in all age groups. The rate of decrease in dental visits per 1000 people for restorative treatments in children and adolescents was higher than that in adults. The rate of decrease in the number of dental visits for multi-visit pulp treatments showed a rapid decrease as compared to that of 1-visit pulp treatments after the pandemic. This study identified changes in the number of dental visits of children and adolescents after COVID-19 transmission in comparison to that observed in adults.

• Journal of the Korean Society of Radiology
• /
• v.16 no.4
• /
• pp.477-490
• /
• 2022

Serious Accident Punishment Act(SAPA) went into effect as of Jan. 27, 2022. The subject of study was the worker of the nuclear medicine department and the investigation was aimed at identifying the present situation of their understanding on the issue in the here and now, which can be utilized as basic research for further study. The survey was conducted on 51 people of the worker in the nuclear medicine department. The general factors were classified by their gender, the scale of the hospitals, the period of career, and the detailed occupational categories. The conclusion was drawn, including 1 missing data in gender and 2 in the type of occupation. The targeted hospitals were tertiary hospital, university hospital, and general hospital which have nuclear medicine department in. The period of subjects' career was categorized by less than 3 years, 3 to 5 years, 5 to 10 years, and more than 10 years. The specific occupation was classified by in-vivo radiological technologist, radiation safety manager and others. The amount of pressure that the job entails was highest in the category of general hospital, the period of 3 to 5 years of job experience, and radiation safety manager each. The system of the code was well constructed in the category of general hospital, the period of less than 3-year career, and radiation safety manager, as they responded. The blood transmissible disease had the largest number of outbreak of accidents related to the serious industrial accident. In addition, the radiopharmaceutical dosing error had the highest number of outbreak of accidents related to the serious civil accident. Therefore, we need to improve SAPA, facility inspection, security of budget, security of professional manpower. It will help the stable use of radiation and ensure patient safety.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.24 no.4
• /
• pp.327-339
• /
• 2022

The purpose of this study is to present the effective smoke control flow rate and mode for securing safety through quantitative risk assessment according to the smoke control flow rate and mode (supply or exhaust) of the platform when a train fire occurs at the subway platform. To this end, a fire outbreak scenario was created using a side platform with a central staircase as a model and fire analysis was performed for each scenario to compare and analyze fire propagation characteristics and ASET, evacuation analysis was performed to predict the number of deaths. In addition, a fire accident rate (F)/number of deaths (N) diagram (F/N diagram) was prepared for each scenario to compare and evaluate the risk according to the smoke control flow rate and mode. In the ASET analysis of harmful factors, carbon monoxide, temperature, and visible distance determined by performance-oriented design methods and standards for firefighting facilities, the effect of visible distance is the largest, In the case where the delay in entering the platform of the fire train was not taken into account, the ASET was analyzed to be about 800 seconds when the air flow rate was 4 × 833 m³/min. The estimated number of deaths varies greatly depending on the location of the vehicle of fire train, In the case of a fire occurring in a vehicle adjacent to the stairs, it is shown that the increase is up to three times that of the vehicle in the lead. In addition, when the smoke control flow rate increases, the number of fatalities decreases, and the reduction rate of the air supply method rather than the exhaust method increases. When the supply flow rate is 4 × 833 m³/min, the expected number of deaths is reduced to 13% compared to the case where ventilation is not performed. As a result of the risk assessment, it is found that the current social risk assessment criteria are satisfied when smoke control is performed, and the number of deaths is the flow rate 4 × 833 m³/min when smoke control is performed at 29.9 people in 10,000 year, It was analyzed that it decreased to 4.36 people.

• Pediatric Infection and Vaccine
• /
• v.29 no.3
• /
• pp.131-140
• /
• 2022

Purpose: Since the coronavirus disease 2019 (COVID-19) pandemic began, new variants of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) have emerged, and distinct epidemic waves of COVID-19 have occurred for an extended period. This study aimed to analyze the clinical and epidemiological characteristics of children with COVID-19 from the third wave to the middle of the fourth epidemic wave in Korea. Methods: We retrospectively reviewed the medical records of hospitalized patients aged ≤18 years with laboratory-confirmed COVID-19. The study periods were divided into the third wave (from November 13, 2020 to July 6, 2021) and the fourth wave (from July 7 to October 31, 2021). Results: Ninety-three patients were included in the analysis (33 in the third and 60 in the fourth waves). Compared with the third wave, the median age of patients was significantly older during the fourth wave (6.7 vs. 2.8 years, P=0.014). Household contacts was reported in 60.2% of total patients, similar in both periods (69.7 vs. 55.0%, P=0.190). Eighty-one (87.1%) had symptomatic SARS-CoV-2 infection. Among these, 10 (12.3%) had no respiratory symptoms. Anosmia or ageusia were more commonly observed in the fourth epidemic wave (10.7 vs. 34.0%, P=0.032). Most respiratory illness were upper respiratory tract infections (94.4%, 67/71), 4 had pneumonia. The median cycle threshold values (detection threshold, 40) for RNA-dependent RNA polymerase (RdRp) and envelope (E) genes of SARS-CoV-2 were 21.3 and 19.3, respectively. There was no significant difference in viral load during 2 epidemic waves. Conclusions: There were different characteristics during the two epidemic waves of COVID-19.