• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.9
• /
• pp.397-404
• /
• 2020

The military tactical vehicle currently being operated is manufactured by improving the parts of commercial vehicles. In addition, the power supply system is applied by installing a separate converter inside the communication room to secure the operating environment of communication equipment. On the other hand, due to electromagnetic radiation noise, there are problems in frequent noise and deterioration in communication sensitivity during wireless communication in vehicles. To improve these, an advanced power supply system is applied, which is also equipped with an alternator to receive power required for communication equipment reducing broadband electromagnetic radiation noise. An additionally installed alternator, which is located in the engine room, is separated from the communication room where communication equipment is operated and is expected to reduce the effect of electromagnetic radiation noise generated from the power supply system. To verify these, a broadband radiation test was performed on a previous and advanced one. As a result, the broadband radiation noise of vehicles with an applied advanced power supply system satisfied all of the domestic vehicle safety standards and reduced in most of the sections except for some frequencies compared to previous typed vehicles. In particular, broadband radiation noise was decreased by up to 10.751 dB𝜇V/m in the vertical sections in 170 to 200 MHz on the right side of the vehicle.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.9 s.100
• /
• pp.883-892
• /
• 2005

We propose a T-shaped UWB printed monopole antenna and investigate the effect of the surface currents of the radiator and ground plane. The measured impedance bandwidth of the antenna covers the range of 3.1 to 11 GHz for a VSWR$\le$2, which satisfies the requirement of the UWB operation. From the analysis of the surface currents, the proposed antenna can be treated as two asymmetric dipoles with the included angle of 90 degrees which lie along z-direction symmetrically. It is observed that the effect of the surface currents on the radiation patterns is similar to that of the corresponding dipole. The length and width of the found plane correspond the radius and length of the dipole respectively. This approach is also valid to general printed monopole antennas. Finally, we included an antenna example having resonance at a lower frequency by tapering the edges of the ground plane and another example having a bandstop characteristic by inserting an inverted-U slot on the radiator, and explain those antennas using the surface currents.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.335-340
• /
• 2005

In this paper, the triple-band planar monopole antennas are designed for cellular communication, WiBro and WLAN(IEEE802.llb/g) communication and WLAN(IEEE802.lla) communication of 5GHz band. Various types of antennas are designed and examined experimentally as bended in the low and middle band radiation elements to decrease antennas size and increased radiation elements width to improve bandwidth. The proposed antennas are improved by 11% in antenna size with bended low-band radiation elements down and are extended by 30%$\sim$40% in bandwidth by increasing the width of the radiation element at 800MHz band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.1
• /
• pp.90-97
• /
• 2010

In this paper, we propose antenna topology and ground plane shape to improve the performance of PIFA (Planar Inverted F Antenna) which is built-in mobile phone. First, we designed the PIFA antenna consists of multiple radiators to provide multi-current paths. Then we designed U-shaped ground plane on the PCB under the antenna. The proposed antenna structure shows TRP/TIS improvement of 2.0 dB/3.7 dB for GSM and 2.2 dB/ 2.0 dB for DCS and 0.8 dB/1.5 dB for PCS and 1.3 dB/0.7 dB for WCDMA at the free space.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.5
• /
• pp.459-467
• /
• 2010

A new type of circularly polarized(CP) antenna that is characterized by having both low-profile and greater axial-ratio bandwidth(ARBW) beyond existing antennas is introduced through analysis of artificial magnetic conductor(AMC) polarizer, and experimentally demonstrated. Although it is made use of a linear-polarized dipole antenna with close proximity to ground plane, it is backed by AMC polarizer so as to efficiently radiate with circularly changed polarization whose ARBW is determined by the texture geometry, whereas existing antennas exhibit CP surface-current on radiators, which limit ARBW. The mechanism of the polarization conversion is theoretically analyzed for ARBW, and the experimental properties including the impedance matching, CP radiation pattern, axial-ratio pattern, ARBW, and two-port isolation are discussed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.12
• /
• pp.1233-1242
• /
• 2009

In this paper, a Base Station Antenna(BSA) utilizing Artificial Magnetic Conductor(AMC) as reflector instead of common conductive plate to improve radiation characteristics and achieve low-profile is proposed. In the case of the conventional BSA on conductive surface which acts as a reflector, a secondary radiation is caused at the corner of the conductive surface, and it increases the back-lobe of the antenna, resulting in deteriorating the radiation characteristic of the conventional BSA. However, using the AMC, the back-lobe of the BSA can be largely reduced by the surface wave suppression. And the Side-Lobe Level(SLL) is also improved, resulting in preventing the service area overlapped. Furthermore, due to the $0^{\circ}$ reflection phase on AMC, the profile of the BSA can be also reduced.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.1
• /
• pp.59-66
• /
• 2011

In this paper, a co-planar waveguide(CPW)-fed zeroth-order resonant(ZOR) antenna with an improved radiation efficiency was built and tested. The unit cell of the proposed antenna consists of a series metal-insulator-metal(MIM) capacitor and a shorted shunt stub inductor. In order to reduce the antenna size and to achieve the high radiation efficiency two shorted shunt stub arms bent by 90 degree were connected to the ground plane through the via. The proposed antenna consisting of two unit cells has an open ended composite right/left-handed(CRLH) transmission line structure. As a result the dominantly radiating parts of the antenna comes from shunt stub arms and vertical vias. The total size of the fabricated zeroth-order resonant antenna is $0.22\;{\lambda}_0{\times}0.22\;{\lambda}_0$. The measured gain and efficiency of the fabricated antenna have been enhanced by 3.07 dBi and 75 %, respectively, at the zeroth-order resonant frequency of 2.97 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.1 s.104
• /
• pp.60-66
• /
• 2006

In this paper, a circular microstrip patch antenna for switchable polarization is presented. For the switchable polarization, pairs of tuning stubs and two PIN diodes are utilized. By independently setting the PIN diodes on or off, the antenna produces either linear polarization or circular polarization. From the results, the -10 dB impedance bandwidths of 57.0 MHz($2.4\%$) and 50.0 MHz($2.1\%$) when operated in the linear polarization, and the 3 dB axial ratio bandwidth of $1.3\%$ with minimum of 0.2 and 0.9 dB in the circular polarization have been observed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.9
• /
• pp.769-776
• /
• 2015

In this paper, a broadband MIMO antenna using the metal cover that is one of the antenna radiators is designed and implemented on the PCB. The proposed antenna consists of a monopole and an IFA fed by the coupling structure and a metal cover radiator. Therefore, a monopole and an IFA with a metal cover radiator operate simultaneously through a hybrid form of operation. The antenna satisfies VSWR 3:1 at the bands of LTE class 13, class 14, CDMA, GSM900, DCS, PCS, WCDMA, LTE class 40 and WiFi. The maximum ECC of diagonally fed MIMO antenna is 0.186. The measured average gain and efficiency were -5.14~-1.28 dBi and 30.87~74.48 % over the desire bands, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.7
• /
• pp.613-619
• /
• 2015

In this paper, we proposed a paper-based pattern-switchable antenna using inkjet-printing technology. The proposed antenna is composed of two bow-tie antennas and a switching network. The bow-tie antennas are inkjet-printed on paper using a low cost home printer. The switching network is built on a printed-circuit-board(PCB) and consists of a single-pole-double-throw(SPDT) switch and balun element. A double-sided parallel-strip line(DSPSL) can convert the unbalanced microstrip mode to the balanced strip mode. Two bow-tie antennas have different radiation patterns because of the different orientation of the reflectors. It is demonstrated from EM simulation and measurement that the radiation patterns of the proposed antenna are successfully switched by the SPDT.