• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.12
• /
• pp.64-72
• /
• 2012

Synchronization including timing recovery, frequency offset compensation, and frame synchronization is most important signal processing block in all wireless/wired communication systems. In most communication systems, synchronization schemes based on training sequences or preambles are used. WLAN standards of 802.11a/g/n released by IEEE are based on OFDM systems. OFDM systems are known to be much more sensitive to frequency and timing synchronization errors than single carrier systems. A loss of orthogonality between the multiplexed subcarriers can result in severe performance degradations. The starting position of the frame and the beginning of the symbol and training symbol can be estimated using correlation methods. Correlation processing functionality is usually complex because of large number of multipliers in implementation especially when the reference signal is non-binary. In this paper, a simple correlation based synchronization scheme is proposed for IEEE 802.11a/g/n systems. Existing property of a periodicity in the training symbols are exploited. Simulation and implementation results show that the proposed method has much smaller complexity without any performance degradation than the existing schemes.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.10
• /
• pp.39-50
• /
• 1998

Wide-band sharp-transition filters are widely used in applications such as wireless CODEC design or medical systems. Since these filters suffer from large sensitivity and roundoff noise, large word-length is required for the VLSI implementation, which increases the hardware size and the power consumption of the chip. In this paper, a low-power implementation technique for digital filters with wide-band sharp-transition characteristics is proposed using CPL (Complementary Pass-Transistor Logic), LWDF (Lattice Wave Digital Filter) and a modified DIFIR (Decomposed & Interpolated FIR) algorithm. To reduce the short-circuit current component in CPL circuits due to threshold voltage reduction through the pass transistor, three different approaches can be used: cross-coupled PMOS latch, PMOS body biasing and weak PMOS latch. Of the three, the cross-coupled PMOS latch approach is the most realistic solution when the noise margin as well as the energy-delay product is considered. To optimize CPL transistor size with insight, the empirical formulas for the delay and energy consumption in the basic structure of CPL circuits were derived from the simulation results. In addition, the filter coefficients are encoded using CSD (Canonic Signed Digit) format and optimized by a coefficient quantization program. The hardware cost is minimized further by a modified DIFIR algorithm. Simulation result shows that the proposed method can achieve about 38% reductions in power consumption compared with the conventional method.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.48-48
• /
• 2011

2010년 약 19.5 GWp 의 규모로 성장한 태양광 시장의 주요 소재는 실리콘을 이용한 태양전지이며, 고성능 및 고효율 태양전지 시장이 급성장 하였다. 이러한 고품질 태양전지에 사용되는 주요 원료인 9N 급 폴리실리콘은 2008년 4월 $265/kg 까지 상승하였으나, 점차 하향안정세에 있으며, 급속한 가격 경쟁을 통해 당분간 장기공급가가 50$/kg 이하로 하락할 것으로 전망된다. 이러한 실리콘 제조기술 중 가장 많이 사용되는 기술은 Trichloro-silane (TCS) 또는 Mono-silane (MS)를 사용하는 기상법인 일명 Siemens 공정이다. 이러한 기상법의 경우 12N 이상의 초고품질 실리콘 제조가 가능하나, 대규모의 설비투자(1억원/폴리실리콘 1톤)와 높은 에너지(120 kWh/kg)가 요구된다. 이에 최근 기상법이 아닌 야금학적인 정련법에 대한 기술이 개발되고 있으며, 이는 금속 실리콘을 슬래그 처리, 편석 분리, 응고 급랭, 전자빔, 플라즈마 등을 이용하여 정련하는 공정을 말한다. 야금학적 정련법은 순도 면에서 기상법에 비하여 낮은 단점이 있음에도 불구하고, 여러 장점들로 인해 활발히 연구되며 점차 실용화 되고 있는 매우 유용한 기술이다. 야금학적 정련법의 주요 장점은 기상법에 비해 약 25% 정도의 설비 투자비로 가능하고, 금속 실리콘을 직접 사용하며, 에너지 payback이 짧다. 또한, 산 및 염화실렌을 사용하지 않으므로 환경 문제를 적게 야기하고, 생산설비의 확장성도 매우 높다. 본 연구에서는 국내 규석광을 이용하여 일련의 정련 공정을 거쳐 고순도SG(Solar Grade)급 실리콘을 제조하고자 하였다. 실리콘 용융 환원로를 개발하고 순도를 높이기 위해 슬래그정련법을 이용하였으며, 생산된 3N 급의 금속 실리콘을 비기상법정련 방식인 일방향 응고와 플라즈마 정련 및 전자기유도 용해법을 이용하여 고순도의 실리콘을 제조하였다. 본 연구에서는 상업생산을 개시한 외국의 E사와 비교하여 산침출공정을 거치지 않으므로 실리콘회수율 및 환경부하 절감의 장점을 갖고 있으며 최종 순도 실리콘 6N 이상, 보론 함유량 0.2 ppm 이하를 달성하였으며, 기존 기상법 대비 약 20%의 전력 감소와 약 13%의 금속실리콘 원료 절감 효과가 있었다. 저가/고순도 SG급실리콘의 제조기술 개발은 향후 세계 태양광 시장에 대한 경쟁력을 확보하고, 시장 점유율 상승에 기여할 수 있으며, 산업 확대를 통한 주변 산업으로의 파급 효과가 매우 클 것으로 예상된다.

• Polymer(Korea)
• /
• v.35 no.1
• /
• pp.35-39
• /
• 2011

In this work, mesoporous carbons (CMK-3) were prepared by a conventional templating method using mesoporous silica (SBA-15) for using catalyst supports in polymer electrolyte membrane fuel cells (PEMFCs). The CMK-3 were chemically activated to obtain high surface area and small pore diameter with different potassium hydroxide (KOH) amounts, i.e., 0, 1, 3, and 4 g as an activating agent. And then Pt-Ru was deposited onto activated CMK-3 (K-CMK-3) by a chemical reduction method. The characteristics of Pt-Ru catalysts deposited onto K-CMK-3 were determined by surface area and pore size analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and inductive coupled plasma-mass spectrometry (ICP-MS). The electrochemical properties of Pt-Ru/K-CMK-3 catalysts were also analyzed by cyclic voltammetry (CV). From the results, the K3g-CMK-3 carbon supports activated with 3 g KOH showed the highest specific surface areas. In addition, the K3g-CMK-3 led to uniform dispersion of Pt-Ru onto K-CMK-3, resulted in the enhancement of elelctro-catalystic activity of Pt-Ru catalysts.

• Journal of the Korean Chemical Society
• /
• v.52 no.1
• /
• pp.30-35
• /
• 2008

purpose of the study was to synthesize new series of 5-cyano substituted pyrimidine analogues with different substitutions at N1 and 6 positions and to evaluate them for antibacterial and antifungal activities. The desired compounds were synthesized by tertiary condensation of ethylcyanoacetate, substituted thioureas and suitable aldehyde in presence of potassium carbonate using MORE technique. The antibacterial and antifungal activities were evaluated by cup plate method in the concentration of 25 mg. The zone of inhibition was measured in mm. All the compounds have shown significant antibacterial and antifungal activities. The maximum activity was shown by P1 and P5 against S.aureus and E.coli respectively, while P6 has shown significant activity against all types of microorganisms. The compound P8 has been found to be significantly effective against C. albicans. Norfloxacin and griseofulvin were used as standards to compare the activites of synthesized compounds. It is concluded that analogues containing p-hydroxy, p-methoxy substituted phenyl moiety at 6 position have been found to be more potent against gram-positive microorganisms, while analogues lacking these substituents on phenyl moiety possessed gram-negative activity. The compounds having p-dimethylamino substituent on phenyl moiety at 6 positions have shown moderate activity. Further, only fluorine containing analogue at N1 position was found to possess appreciable antifungal activity. This suggests that electron donating substituent on aryl moiety as well as electron withdrawing substituent at N1 plays important role in determining potency of the compounds.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.38 no.4
• /
• pp.11-17
• /
• 2001

In this paper, we propose a polarity decision carrier recovery algorithm for high order QAM(Quadrature Amplitude Modulation), which has robust and large frequency acquisition performance in the high order QAM modem. The proposed polarity decision PD(Phase Detector) output and its variance characteristic are mathematically derived and the simulation results are compared with conventional DD(Decision-Directed) method. While the conventional DD algorithm has linear range of $3.5^{\circ}{\sim}3.5^{\circ}$, the proposed polarity decision PD algorithm has linear range as large as $-36^{\circ}{\sim}36^{\circ}$ at ${\gamma}-17.9$. The conventional DD algorithm can only acquire offsets less than ${\pm}10\;KHz$ in the case of the 256 QAM while an analog front-end circuit generally can reduce the carrier-frequency offset down to only ${\pm}100\;KHz$. Thus, in this case additional AFC or phase detection circuit for carrier recovery is required. But by adopting the proposed polarity decision algorithm, we can find the system can acquire up to ${\pm}300\;KHz$at SNR = 30dB without aided circuit.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.7
• /
• pp.32-37
• /
• 2008

Satellite communication systems including the DVB-S2 (Digital Video Broadcasting - Satellite Version 2) system require operations under low signal-to-noise ratio (SNR) and large frequency offset values, and the initial frame synchronization process necessitates a robust correlation method. While a variety of conventional correlation structures exist for the initial synchronization, each method has different characteristics and performance in different channel environments. In this paper, we propose new correlation methods which exhibit enhanced performance in low SNR and large frequency offsets, and analyze their performance. The proposed methods use the magnitude sum and vector sum of extended differential correlation values, to maximize the correlation between the received signal and the synchronization sequence by using the spanned differential correlation result. The magnitude sum correlation method has better performance compared to conventional methods including the approximated ML (Maximum likelihood) method for SNR values below 4 dB with or without frequency offsets. The vector sum correlation method has improved performance over the magnitude sum method for channels with relatively small frequency offsets.

• Clean Technology
• /
• v.25 no.1
• /
• pp.14-18
• /
• 2019

In general after the etching process, waste etching solution contains metals. (ex. Nickel (Ni), Chromium (Cr), Zinc (Zn), etc.) In this work, we proposed a recycling process for waste etching solution and refining from waste liquid contained nickel to make nickel metal nano powder. At first, the neutralization agent was experimentally selected through the hydrolysis of impurities such as iron by adjusting the pH. We selected sodium hydroxide solution as a neutralizing agent, and removed impurities such as iron by pH = 4. And then, metal ions (ex. Manganese (Mn) and Zinc (Zn), etc.) remain as impurities were refined by D2EHPA (Di-(2-ethylhexyl) phosphoric acid). The nickel powders were synthesized by liquid phase reduction method with hydrazine ($N_2H_4$) and sodium hydroxide (NaOH). The resulting nickel chloride solution and nickel metal powder has high purity ( > 99%). The purity of nickel chloride solution and nickel nano powders were measured by EDTA (ethylenediaminetetraacetic) titration method with ICP-OES (inductively coupled plasma optical emission spectrometer). FE-SEM (field emission scanning electron microscopy) was used to investigate the morphology, particle size and crystal structure of the nickel metal nano powder. The structural properties of the nickel nano powder were characterized by XRD (X-ray diffraction) and TEM (transmission electron microscopy).

• Journal of IKEEE
• /
• v.27 no.3
• /
• pp.340-344
• /
• 2023

In this paper, we propose a study on the development of deep learning structure to secure visibility of outdoor LED display board according to weather change. The proposed technique secures the visibility of the outdoor LED display board by automatically adjusting the LED luminance according to the weather change using deep learning using an imaging device. In order to automatically adjust the LED luminance according to weather changes, a deep learning model that can classify the weather is created by learning it using a convolutional network after first going through a preprocessing process for the flattened background part image data. The applied deep learning network reduces the difference between the input value and the output value using the Residual learning function, inducing learning while taking the characteristics of the initial input value. Next, by using a controller that recognizes the weather and adjusts the luminance of the outdoor LED display board according to the weather change, the luminance is changed so that the luminance increases when the surrounding environment becomes bright, so that it can be seen clearly. In addition, when the surrounding environment becomes dark, the visibility is reduced due to scattering of light, so the brightness of the electronic display board is lowered so that it can be seen clearly. By applying the method proposed in this paper, the result of the certified measurement test of the luminance measurement according to the weather change of the LED sign board confirmed that the visibility of the outdoor LED sign board was secured according to the weather change.

• Applied Biological Chemistry
• /
• v.40 no.1
• /
• pp.80-84
• /
• 1997

Series of new chiral N-substituted benzotriazol-1-yl derivatives were synthesized and their fungicidal activities in vitro against gray mold(Botrytis cinerea), black spot(Alternaria kikuchiana) and phytophthora blight(Phytophthora capsici) were measured by the agar medium dilution method. The substituents effects between the fungicidal activities (obs. $pI_{50}$) and a various physicochemical parameters of phenoxy or thiophenoxy group(X) & alkyl or phenyl group(Y) were analyzed by the multiple regression technique. From the analyzed substituent effects, the structure-activity relationship(SAR) equations shows that the antifungal activities depend on the parameters for the optimal molecular hydrophobicity($({\Sigma}logP)_{opt}$), Van der Waals (${\Sigma}Vw$>0) volume(${\AA}^3$) and inductive constant with electron withdrawing group(${\sigma}_I$,Y>0). The activity in affected by the inductive effect (${\sigma}_I$,Y>${\sigma}_g$X) of Y-group rather than the X-group. The phenoxy substituents, 1, showed higher antifungal activity tn the thiophenoxy substituents, 2. For 1, polar substituent constant(${\sigma}^*$) was an important factor in determining the activity. And the tribromomethyl substituent, 1g showed the highest activity against the tee fungi.