• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.232.1-232.1
• /
• 2013

본 연구에서는 asymmetric과 symmetric 구조의 n채널 MOSFET 소자의 성능 평가에 관한 실험을 진행하였다. 소자의 성능 평가에 있어 아날로그 회로에서의 DC 이득은 중요한 파라미터 중 하나 이다. 따라서 본 연구에서는 gm/ID 측정법을 이용하여 각 소자의 DC 이득 특성을 분석하였다. 게이트 전압에 따른 드레인 전류-드레인 전압 특성 곡선으로부터 early voltage 값을 추출하였다. 이후 최종적으로 수치적 계산을 통해 DC 이득 값을 추출하였다. 실험 결과 asymmetric과 symmetric 소자의 경우 early voltage 값이 각각 -34 V와 -15 V였으며 따라서 DC 이득 특성 또한 asymmetric 소자의 경우가 우수한 것을 확인하였다.

• Bulletin of the Korea Photovoltaic Society
• /
• v.7 no.2
• /
• pp.7-15
• /
• 2021

태양광 발전소에 대한 성능을 평가하기 위해서는 IEC 61724-1에 적합한 계측장치를 설치하고 데이터를 수집하여 평가하는 것이 일반적인 방법이다. 본 논문에서는 태양광발전소 현장에서 DC 어레이 성능을 평가하기 위한 방법을 제시하였다. 측정 일사량과 같은 환경정보 값과 태양광 DC 어레이 전압-전류 특성 곡선을 이용해 일사량에 따른 출력모델 식을 도출하였다. 도출된 모델 식은 태양전지 셀의 종류나 버스바에 따라서 차이가 발생되므로 기존의 태양전지 셀 등가회로 수식을 반영한 시뮬레이션 모델식이 적절히 변경되어야 함을 실험을 통해 검증하였다. 주기적인 진단 평가를 실시하지 않는 국내외 태양광 발전소는 성능저하가 발생된 상태로 운전되는 경우가 다수 일 것이다. 대부분의 관제모니터링을 시스템은 미쓰매칭 손실 평가분석이 불가능하며 운전상태 모니터링 하는 시스템이 대부분이다. 이에 태양광 발전소의 효율적 운영을 위해서는 현장진단 장치를 이용한 주기적 성능진단 평가나 발전소 데이터의 손실평가 분석 기술의 개발이 필요할 것이다.

• Journal of the Korean Electrochemical Society
• /
• v.10 no.3
• /
• pp.196-202
• /
• 2007

The performance characteristics of the polymer electrolyte fuel cells (PEFCS) were investigated under various humidification conditions at steady-state and transient conditions. The PEFC studied in this study was characterized by I-V curves in the potentiostatic mode and EIS (electrochemical impedance spectroscopy). The I-V curves representing steady-state performance were obtained from OCV to 0.25 V, and the dynamic performance responses were obtained at some voltages. The effects of anodic external humidification were measured by varying relative humidity of hydrogen from 20% to 100% while dry air was supplied in the cathode. At the high voltage region, the performance became higher with the increase of the temperature, while at the low voltage region, the performance decreased with the increase of temperature. The EIS showed that ohmic losses were larger at the dry condition of membrane and the effects of mass transport losses increased remarkably when the external and self-humidification were high. The dynamic responses were also monitored by changing the voltage of the PEFC instantly. As the temperature increased, the current reached steady-state earlier. The self-humidification with the generated water delayed the stabilization of the current except for low voltage conditions.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.73-76
• /
• 2008

Bipolar Plates for PEMFC have been a key component of fuel cells with MEA, thus in this research they have been fabricated by a compression molding technique after mixing graphite powder with phenol resin. The results have shown the prominent properties compared with those by foreign advanced company with respect to the electrical conductivity and flexural strength. In addition, it has been carried out that the Voltage-Current characteristics comparison according to the unit cell experiments of bipolar plates. As a result, we have obtained good performances and we are going to research the molding feasibility of bipolar plate's flow channel.

• Journal of the Korea Convergence Society
• /
• v.12 no.5
• /
• pp.17-22
• /
• 2021

Eco-friendly magnesium-air battery is a kind of metal-air battery known as a primary battery with a very high theoretical discharge capacity. This battery is also called a metal-fuel cell from the viewpoint of using oxygen in the atmosphere as a cathode active material and magnesium alloy as a fuel. Since battery performance is determined by the properties of the magnesium alloy used as a anode, more research and development of the magnesium alloy electrode as a anode material are required in order to commercialize it as a high-performance battery. In this study, the commercialized magnesium alloys(AZ31, AZ61) were selected and then electrochemical measurements and discharge test were conducted. Electrochemical properties of magnesium alloys were investigated by OCP changes, Tafel parameters and CV measurement, and the feasibilities of AZ61 alloy with excellent discharge capacity(1410mAhg^-1) as electrode materials were evaluated through CC discharge experiments.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.6
• /
• pp.513-518
• /
• 2015

Salinity gradient power (SGP) has attracted significant attention because of its high potential. In this study, we evaluate reverse electrodialysis (RED) with various compositions of available resources. The polarization curve (I-V characteristics) shows linear behavior, and therefore the power density curve has a parabolic shape. We measure the power density with varying compartment thicknesses and inlet flow rates. The gross power density increases with decreasing compartment thickness and increasing flow rate. The net power density, which is the gross power density minus the pumping power, has a maximum value at a compartment thickness of 0.2 mm and an inlet flow rate of 22.5 mL/min. The power density in RED is also evaluated with compositions of desalination brines, seawater, river water, wastewater, and brackish water. A maximum power density of $1.75W/m^2$ is obtained when brine discharged from forward osmosis (FO) and river water are used as the concentrated and the diluted solutions, respectively.

• Journal of the Korean Applied Science and Technology
• /
• v.30 no.1
• /
• pp.146-151
• /
• 2013

This paper reveals the performance decrease and recovery of PEMFC when the contaminated fuel gas and air source with sulfur impurities such as hydrogen sulfide and sulfur dioxide were simultaneously introduced to anode and cathode, respectively. Three different GDLs were fabricated with different carbon black and activated carbon to prevent an introduction of sulfur compound impurities into MEA. components. The severity of $SO_2$ and $H_2S$ poisoning was depended on concentrations(3 ppm - 10 ppm) of sulfur impurities. Especially, cell performance degradation rate was rapid when MEA fabricated with CN-2 GDL because it had little porosity on GDL surface. Moreover, the cell performance can be recovered up to 90%-95% only with neat hydrogen and fresh air feeding.. Conclusively, MEA fabricated with porous CN-1 GDL showed the best cell performance and recovery efficiency during exposure to poisoning condition by simultaneous sulfur impurities.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.11a
• /
• pp.399-402
• /
• 2006

현재까지 연료전지 전해질 막으로는 Nafion으로 잘 알려져 있는 perfluorosulfonic acid(PFSA)막이 주를 이루고 있다. 이 막들은 $80^{\circ}C$ 이하의 낮은 온도의 연료전지에서 가장 좋은 성능을 보인다. PFSA 막들은 탄소-불소로 이루어진 사슬의 특성상 산화, 환원의 조건에서도 뛰어난 안정성을 보이며 이온 전도도가 0.1S/cm 이상으로 기존에 알려진 전해질 막들 중 가장 우수한 성능을 나타낸다. 하지만 연료전지의 작동온도가 $100^{\circ}C$ 이상의 높은 온도에서 는 막에 존재하던 수분이 제거되면서 수소이온 전도도가 떨어지며 기계적 물성도 떨어지는 문제점을나타낸다. $100^{\circ}C$ 이상의 온도에서 연료전지를 작동시키면 양쪽의 전극에서 일어나는 촉매반응의 속도가 향상되며, 물의 끓는점 이상에서 작동되므로, 전지 내에서 다양한 상을 고려하지 않고 기화된 물만을 고려하여 설계를 할 수가 있다. 따라서 최근 이러한 고온/저가습 운전을 위 한 전해질 막의 개발을 위해 기존의 Nafion 막에 전도성 무기 입자를 도입하는 연구들이 활발히 진행되고 있다. 본 연구에서는 전도성 무기 입자로서 $ZrO_2$나노입자를 합성하고, 이를 상용 10 wt.% Nafion 용액에 분산하여 solution casting 방법을 통해 $61{\mu}m$ 두께의 유기-무기 복합막을 제조하였다. 제조한 유기-무기 복합막의 성능 평가를 위하여 함수율, 이온 전도도, 당량무게 및 단위 전지를 이용한 전류-전압 곡선을 측정하여 상용 Nafion 112 막과 비교해 보았다. $ZrO_2$ 입자는 전도성이며 동시에 친수성을 나타내기 때문에 상용 막에 비하여 함수율 및 수소이온 전도도가 우수하게 나타났다. 복합막의 이러한 물성은 $100^{\circ}C$이상의 고온에서 전해질 막 내의 물 관리를 용이하게 한다. 단위 전지 운전 온도 $130^{\circ}C$, 상대습도 37%의 운전 조건에서도 상당히 우수한 전지 성능을 보임에 따라 고온/저가습 조건에서 상용 Nafion 112 막보다 우수한 막 특성을 나타냄을 확인하였다.

• Journal of the Korean Electrochemical Society
• /
• v.19 no.2
• /
• pp.39-44
• /
• 2016

Oxygen reduction reaction in the fuel cell (ORR) plays a dominant role in the overall reaction. In addition, the low compatibility between the membrane and the binder consisted of different materials, greatly reduces the efficiency of the fuel cell performance. In view of these two problems, geometrically modified copolymers with 9.9_Bis (4-hydroxyphenyl) were synthesized via condensation reaction instead of conventional biphenol and were adopted as hydrocarbon ionomer binders. By utilizing these binders, two kinds of MEAs using fluorinated Nafion membrane and hydrocarbon based membrane were manufactured in order to electrochemical performance evaluation. With current-voltage curves, there was no significant difference in the 0.6 V when two types of membrane were applied. Also, tafel slope became considerably lower as compared to the Nafion membrane. Thus, it is determined that the new hydrocarbon binder is expected to contribute the improvement in performance of fuel cells.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.3
• /
• pp.169-173
• /
• 2015

This study is to predict the life exponent by measuring, over 7 years, the insulation resistance of high-voltage cables in 22 kV operation for 13 years. We found out the lifetime index in order to determine the time-dependent trend of deteriorating performance of power cables. The insulation resistances decreased according to elapsed time. We found that: the initial measurements of the cable systems were in agreement with the deterioration properties of the Arrhenius Law. By analyzing the life curve of the cable system, we also verified that the value of the life exponent (n) in the v-t characteristics defined by Weibull distribution has values from 10 to 11. When designing the cable system, the initial value of life exponent was chosen as 9 without any grounding. We have verified that the theoretical grounding based on the design safety of n=9 was actually the best one available. In the short term, we apply our research result to the diagnosis and evaluation of the power cables. In the long run, however, we plan to reduce the cost of the installation and management of cable systems in operation at power stations.