• 한국전산유체공학회지
• /
• 제16권1호
• /
• pp.14-21
• /
• 2011

Super-cavitating flows around under-water bodies are being studied for drag reduction and dramatic speed increase. In this paper, high speed super-cavitating flow around a two-dimensional symmetric wedge-shaped body were studied using an unsteady Reynolds-averaged Navier-Stokes equations solver based on a cell-centered finite volume method. To verify the computational method, flow over a hemispherical head-form body was simulated and validated against existing experimental data. Various computational conditions, such as different wedge angles and caviation numbers, were considered for the super-cavitating flow around the wedge-shaped body. Super-cavity begins to form in the low pressure region and propagates along the wedge body. The computed cavity lengths and velocities on the cavity boundary with varying cavitation number were validated by comparing with analytic solution.

• 한국전산유체공학회지
• /
• 제17권2호
• /
• pp.78-84
• /
• 2012

Numerical calculations were performed to investigate the influence in aerodynamic characteristics of a rotor system by surrounding structures and the ground effect for the rotor blade on a whirl tower is also investigated. Three dimensional Navier-Stokes simulations were carried out by using unstructured overset mesh technique and parallel computation. The calculated hover performance showed good agreement with the experimental result and showed that the structures around the whirl tower did not affect the aerodynamic characteristics of the blade. The ground effect was studied by comparing with the numerical result for the out of ground condition and the result of an analytic model.

• 한국전산유체공학회지
• /
• 제17권2호
• /
• pp.65-70
• /
• 2012

The droplet ejection behavior from drop-on-demand printhead are investigated numerically in terms of the non-dimensional parameters. The numerical simulation is performed using a volume-of-fluid model. It is important to eject droplet within the printability range, where the droplet is ejected in stable manner without satellite droplets. Generally, the printability range has been determined by Z number, which is the inverse of Oh number. However, it is found that the ejection of droplets with same Z number can exhibit different behavior depending on the value of Ca and We number. Therefore, it is insufficient to determine the printability range only with Z number. Instead, other non-dimensional parameters, such as Ca and We number, should be considered comprehensively.

• 한국전산유체공학회지
• /
• 제1권1호
• /
• pp.1-8
• /
• 1996

본 논문은 전산 유체 역학에서 필요한 3차원 다구획 격자구성 프로그램을 개발한 것이다. 유동장에 격자를 구성하는 것은 유동해석 방정식을 푸는 것 보다 일반적으로 시간이 더 소요되므로 격자구성 시간을 단축하기 위해서 사용자 편의를 도모하는 컴퓨터 화면과의 대화형 코드를 개발하였다. PIGG라고 부르는 본 격자구성 프로그램은 형상 모델링, 표면격자 구성, 유동장격자 생성, 그리고 격자의 재구성에 이르는 일련의 과정이 대화형/화면게시 형태로 수행된다. 본 PIGG를 이용하여 전통적인 전투기 형상 격자를 구성한 결과 많은 시간을 단축할 수 있었다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 1995년도 추계 학술대회논문집
• /
• pp.90-103
• /
• 1995

최근 전산 유체 역학은 Navier-Stokes 방정식을 보다 복잡한 유동장 형상에 대해 풀 수 있을 만큼 발달해 왔으나 아직도 유동장 형상이 복잡할 때는 많은 애로를 느끼고 있다. 특히 격자 구성 문제에 있어서 많은 시간과 노력을 기울이고 있으며 심지어 격자 구성 문제를 해결하지 못해 유동해석을 하지 못하는 경우가 많은 실정이다. 따라서 본 연구에서는 주로 내부 유동인 변형 도관를 예로 유동장 형상에 따라 격자구성이 어떻게 달라지는가를 살펴 보았다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2007년도 추계 학술대회논문집
• /
• pp.162-166
• /
• 2007

In the present study, the pressure coefficient of a cubic building model is numerically simulated. Three turbulence models of standard ${\kappa}-{\varepsilon}$, RNG ${\kappa}-{\varepsilon}$ and LES are adopted and the results are compared with the available experimental data. From the results, it has been found that RNG ${\kappa}-{\varepsilon}$ turbulence model and LES turbulence model were shown to predict fairly well the experimental pressure coefficient. In contrast, the results of the standard ${\kappa}-{\varepsilon}$ turbulence model showed large discrepancies in pressure coefficient on the side and top surfaces of the cubic building, which limits the applicability of the standard ${\kappa}-{\varepsilon}$ turbulence model on wind engineering.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2007년도 추계 학술대회논문집
• /
• pp.171-176
• /
• 2007

Supersonic viscous flow over a 5 degree half angle cone studied computationally with three-dimensional Navier-Stokes equations. Steady asymmetric solutions of 5-deg half angle cone show that the asymmetric flow separation is caused by convective instability. The angle of attack, Reynolds number, and Mach number affected the side force variation that is caused by asymmetric vortical flow.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2007년도 추계 학술대회논문집
• /
• pp.73-76
• /
• 2007

The present paper describes the results of performance analysis for UH-60A rotor blade in hover. For the numerical simulations, commercial CFD software, FLUENT was used with Spalart-Allmaras turbulence model. The flow solver was based on node based scheme and second order spatial accuracy options was used for simulations. For the enhancement of wake capturing capability, high resolution grid was used around tip vortex region. Granting that somewhat over prediction of thrust was observed near blade tip region, performance was well correlated with experimental data within 3% accuracy in the operating region. Finally it was shown that the present flow solver can be used for preliminary performance analysis tool for hovering helicopter rotor blades.

• 한국전산유체공학회지
• /
• 제21권1호
• /
• pp.72-77
• /
• 2016

In this study, effects of thurster axis tilting angle on the thruster-hull interaction and propulsion performance in a dynamic positioning system of offshore plant are numerically investigated. Straight and 7-degree tilted downward thruster models as a form of ducted propeller are considered. For numerical simulations, Reynolds averaged Navier-Stokes equations with SST turbulence model are solved by using STAR-CCM+. Results show that thruster-hull interaction is reduced in 7-degree tilted thruster model with lower vortex strength between thruster and hull bottom, although the propulsion performance does not have noticeable difference in a bollard condition.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2010년 춘계학술대회논문집
• /
• pp.277-282
• /
• 2010

Imported vane type air motor and-piece is used widely in the domestic dental services. The imported hand-pieces are more than 90 percent in the domestic market. The air-motor unit of the hand-piece had not been developed inside of the country yet. Therefore it needs some research works. Purpose of this study is to design the air motor of the hand-piece for better performance. The geometry of the air-motor is based on product of NSK Company. The airflow of the air motor unit is simulated by Computational Fluid Dynamics. The performance analysis of the air motor units is investigated. ANSYS 12.0 CFX is used to analysis of the flowfield. Torque changes depends on spin calculated by the immersed solid method.