• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.13 no.5
• /
• pp.21-26
• /
• 2014

This paper proposes a frequency reconfigurable antenna which operates at not only LTE but also other currently serviced bands. The high band(1,710-2,170 MHz) performance was satisfied through PIFA structure, and the low band performance through the additional RF Switch by changing the state between SW1 and SW2. When the RF switch is SW1 state, the operation bandwidth is 782-907 MHz (GSM), and 738-861 MHz (LTE) at OFF state. The proposed antenna has a omni-directional radiation pattern and measured peak gains were 0.04-4.68 dBi at the SW1 state and 0.92-1.53 dBi at the SW2 state, respectively. Judging from the results, proposed reconfigurable antenna is expected to be applied to LTE-Advanced mobile terminals since the antenna shows an outstanding performance.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.9
• /
• pp.930-935
• /
• 2009

This paper describes a miniaturezed metamaterial BT chip antenna for mobile devices. The size of the proposed antenna is $3.0\;mm(W){\times}2.0\;mm(L){\times}1.2\;mm(H)$. And it is fabricated by chip type. The zeroth-order resonant properties are analyzed by magnitude and phase distributions of the surface current using surface current scanning system. The antenna offers omni-directional radiation patterns and measured 3D average gain is over - 1.7 dBi.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.3
• /
• pp.397-404
• /
• 2020

In this paper, the propagating-wave attenuation characteristics at 1, 3, and 6 GHz in the open environment roadway where the ground-reflected wave dominates are analyzed through a propagation model simulation using a ray-tracing method and propagation measurements. Simulations has been performed by varying the ground material, the transmitting antenna height, and the receiving antenna height. The measurements were conducted using a directional transmission antenna installed at 10 m mast and a omnidirectional receiving antenna installed at 1.5 m mast in an open environment. Comparison of simulation and measurement results confirms that the null points having the weak signal strength depend on those parameters. Although this research has been investigated for the wide road, the derived result could be useful for installing the transmitter and receiver in the roadway open environment.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.10
• /
• pp.1189-1195
• /
• 2007

We design and fabricate, in this parer, a triple band folded monopole antenna for the folder type mobile phone handset that can be served GSM/DCS/USPCS mobile phone system. Antenna structure is modified meander shape which is obtained both extension of antenna physical length for GSM band and same directional multi-currents flowing on the antenna conductor surface for DCS/USPCS band. This antenna has as good performances as high radiation resistance and gain increment, and would be applied to mobile phone handset that is not able to be performed by internal antenna. By measurement, fabricated antenna by the press process shows under VSWR 3:1 at closed folder state and 2:1 at opened folder state over whole GSM/DCS/USPCS band, and has maximum gain as -0.02 dBi for GSM, +0.2 dBi for DCS, +0.78 dBi for USPCS band with almost omnidirectional H-plane radiation pattern.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.11
• /
• pp.1133-1136
• /
• 2011

In this paper, we proposed a collinear antenna with a stripline structure for IEEE 802.11b/g applications in ISM (Industrial, Scientific, Medical) band of 2.4~2.5 GHz, which supplements disadvantages of COCO(Coaxial Collinear) antenna and OMA(Omnidirectional planar Microstrip Antenna). By using the proposed 4-layer substrate, we obtained improved performances and advantages in production compared with the existing antenna. In order to get antenna arrays, the same phase structure is designed by alternatively connecting outer conductor to inner conductor with ${\lambda}$/2 antenna element, and the substrate of FR4 epoxy (${\epsilon}_r$=4.4, tan${\delta}$=0.02) was used for the actual implementation. The maximum gain of about 4.93 dBi was measured, which leaded to a little improved gain of 0.33 dBi in comparison to the existing OMA structure.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.3
• /
• pp.10-14
• /
• 2017

A reverberation chamber is widely used in mobile handset measurements due to its faster and simpler measurement process compared to traditional anechoic chambers. We propose an ultra-wideband inverse conical antenna design suitable as a reference antenna in a reverberation chamber. Traditionally, multiple discone antennas are needed to cover more than 10:1 operation bandwidth of a reverberation chamber. The proposed inverse conical antenna offers wideband impedance matching bandwidth by virtue of the linear impedance transition along its oblique side. The antenna is feasible to mount on the conductive walls which can be utilized as a ground to improve the matching bandwidth, antenna gain and radiation patterns. The antenna geometry is optimized using a 3D electromagnetic simulation tool and fabricated using a 3D printer. The measured results show that the antenna reflection coefficient lower than -10dB and radiation efficiency more than 70% at the frequency range of 0.65~7 GHz.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.12
• /
• pp.52-58
• /
• 2009

We propose a folded monopole antenna with loads, and analyze the roles of design parameters which affect the return loss of the proposed antenna. VSWR < 3 bandwidth of the antenna is 30 ~ 2000 MHz, ranging from the HF/VHF/UHF bands. For operating travelling antenna, we connect six loads at the end of the antenna. The reflected wave is drastically reduced due to the six loads. For improved return loss properties, we use Klopfenstein tape that determine positions and values of six loads. The propose antenna has omni-directional radiational patterns like that of conventional monopole antennas. For wideband impedance transformation, we use the balun which operating frequency region is 10 ~ 1900 MHz. We expect the proposed antenna has important role for the wideband and multi-rold multi-functional communication systems.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.8
• /
• pp.906-912
• /
• 2008

We designed and implemented a 3-dimensional structure internal antenna which has volume less than 1.5 cc for mobile phone to improve efficiency and gain. Multiple bending for the resonance of small internal antenna derives reduction of gain due to cancellation of antenna current. In this study, the current cancelation was reduced by the minimization of antenna bending. And the helix element was applied for the purpose both compensation of short antenna length and action of radiation element. For the verification of this study, a 1.5 cc volume 3D antenna which was fabricated by the press method applied to the dual band mobile phone. Measurement showed that efficiencies and gains under the slide down and up were 27.73 %, 0.29 dBi for the GSM band and 46.84 %, 2.27 dBi for the USPCS band, and had good performance under the small antenna volume. H-plane radiation pattern showed omnidirectional for the both band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.5
• /
• pp.516-521
• /
• 2011

In this paper, an inverted-triangle patch UWB antenna with an uneven ground planes and an inverted T-slot for 5 GHz WLAN band rejection is presented. The operating bandwidth of the proposed antenna fed with the CPW line is expanded from 3.1 GHz to 10.6 GHz for about -10 dB return loss using three angular parameters correlated to the main patch and the ground plane. The fabricated antenna on Taconic RF-60A substrate with 6.16 relative dielectric constant and 0.64 mm thickness has a main antenna patch size of 36 mm${\times}$19.5 mm. The measured results show return losses of about -10 dB and nearly omni-directional radiation patterns. The proposed UWB antenna has advantages of easily adjustable impedance characteristics by the three angular parameters and easily accomplishable band rejection characteristics by the inverted T-slot.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.11
• /
• pp.1194-1200
• /
• 2009

An internal antenna which has 1 cc volume was implemented on the FPCB(Flexible Printed Circuit Board) for the mobile phone. We increased antenna gain and efficiency by the applying of current direction concept on the antenna pattern for this small antenna. Short antenna length for the GSM band was compensated by the spiral inductor on the FPCB. For broadening bandwidth on GSM band, it's applied 2 spiral inductors. A conductor pattern for the DCS band was positioned perpendicular with the FPCB. Antenna was implemented on FPCB that is dielectric constant 4.4 and thickness 0.05 mm, and FPCB was attached on a carrier dimensioned $L{\times}W{\times}H=30{\times}7{\times}5\;mm$. Measurements showed that max. VSWR 2:1, efficiency 42.49~60.95 % and 47.95~73.21 %, average gain -3.72~-2.15 dBi and -3.19~-1.35 dBi on the GSM and DCS band, respectively. These results are good performances among the small antenna. And the radiation patterns are omnidirectional on the H-plane to both band.