• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.140-140
• /
• 2017

4륜 장착 자동차의 토크 전달은 2륜 구동, 4륜 구동 모드를 간단히 전환하는 방식(part time 4WD)과 항시 사륜 구동 모드에서 전후륜의 토크 전달비를 제어하는 방식(AWD, all wheel drive)이 있다. 경제의 발달에 따라서 취미 인구의 확대로 국내에만 180만 명의 R/C car 사용자가 있다. 이 중 2WD-4WD의 전환을 differential lock mechanism으로 구현한 수입산 모델의 가격이 1,000,000원을 호가하지만 가변 제어 방식이 아닌, 정차 후 2-4륜 구동 전환 방식을 적용하고 있으며 상대적으로 내구성이 떨어진다. DC motor의 출력이 늘어나고 배터리의 성능이 좋아진 현재 소형 RC car의 최고 속도는 80 km/h 정도로 빨라졌다. 그러나 마찰 계수가 낮은 노면(실내의 대부분 평활 처리된 복도)에서는 2륜 구동 모드의 활용도가 매우 낮다. 미끄러운 노면에서 후륜 구동 모드로는 oversteer가 발생하여 차량이 스핀하기 쉽고 전륜 구동 모드로는 understeer가 발생하여 제대로 된 코너링이 어렵다. 상시 4륜 구동 모드는 에너지 소모가 크고 전후륜이 tight coupling되어 있는 문제 때문에 일반적인 노면에서 부드러운 코너링이 잘 이루어지지 않는 문제가 있다. 본 연구에서 제안하는 방식은 그림 1와 같이 center shaft의 중간에 영구 자석으로 만들어진 토크 전달용 판이 있고 그 사이에 자계를 차폐할 수 있는 강자성체 셔터를 서보 기구에 연결하여 서보 회전각에 따라서 구동 쪽의 토크가 피구동축으로 전달되는 양을 연속 가변제어할 수 있다. 토크 전달용 판의 차폐 면적에 따른 토크 전달양을 전/후륜 바퀴의 Static torque를 통해 측정하였으며(그림 2), 공중 상태에서 즉 공기저항만을 고려한 상태에서의 RPM 회전수 차이 측정(그림3)을 통해 구동 쪽의 회전수가 피구동축으로 전달되는 양을 측정하여 연속가변 토크 제어 전달 기구의 성능을 확인하였다. 이 기구는 현재 1차적으로는 remote controller의 ch 3(ON/OFF제어 방식)에 연결하여 특정한 양의 토크를 전륜 쪽으로 보낼 수 있도록 구현이 가능하며, ch 2(PID제어 방식)에 연결하여 연속 가변 조절이 가능하도록 구현이 가능하다. 부가적으로 Arduino board를 내장하여 전후륜의 휠센서에서 입력되는 신호를 감지하여 자동적으로 전후륜에 배분되는 토크를 제어할 수 있도록 설계 중에 있다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.1
• /
• pp.45-52
• /
• 2016

One commercial package for magnetic analysis was used to apply repulsive forces of permanent magnetics to bicycle cushion system. Reliabilities of finite element analysis were acquired by comparing with those of experimental measurements. Equivalent spring stiffnesses corresponding to various sizes of magnetics were implemented into the bicycle dynamic model with three degree of freedom. Input force caused at front and rear wheels due to road unevenness was considered in the dynamic model. Dynamic behaviors were observed in terms of vertical displacements of the rider and the front reach as well as pitching displacement of the mass center when the bicycle ran over half-triangular bump. The methodology suggested in this paper by the finite element analysis and numerical model will be an useful tool for more accurate prediction of cushion design for any vehicle system if magnetic forces are utilized.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.10
• /
• pp.1042-1048
• /
• 2008

Disc brake noise is an important customer satisfaction and warranty issue for many manufacturers as indicated by technical literature regarding the subject coming from Motor Company. This research describes results of a study to assess disk brake squeal propensity using finite element methods and optimal technique (Kriging). In this study, finite element analysis has been performed to determine likely modes of brake squeal. This paper deals with friction-induced vibration of disc brake system under contact friction coefficient. A linear, finite element model to represent the floating caliper disc brake system is proposed. The complex eigen-values are used to investigate the dynamic stability and in order to verify simulations which are based on the FEM model. In this paper, Kriging from among the meta-modeling techniques is proposed for an optimal design scheme to reduce the brake squeal noise.

• Journal of the KSME
• /
• v.25 no.3
• /
• pp.198-203
• /
• 1985

제동시 균형 문제나 약간 무거운 조향력등의 전륜구동장치을 설계하기 위한 단점들은 Negative 또는 Zero scrub Radius 의 현가장치를 가능케 하는 이론적 기술적 보완 및 해결이 되고 또한 X형 브레이크 파이프 개발로 한 회로 파열에서도 더욱 안정된 제동을 할 수 있게 된다. 따라서 (1) 중. 소형 승용차에서 절대적 비중을 차지하고 있는 실내 유효공간을 훨씬 크게할 수 있는 점 (2) 후륜구동에 비해 손쉽고 갑싸게 4륜 독립 현가장치가 가능하기 때문에 승차감에서 탁월한 개선이 이루어 진다는 점 (3) 우수한 직진(방향) 안정성과 선회성능을 얻을 수 있는 점 (4) 경량화 및 전동(轉動) 손실 감소에 따른 연비 향상 등의 커다란 장점으로 전륜구동차는 기술적인 면에서 후륜구동차에 비하여 그 격을 달리하고 있으며 몇 년 전부터 모든 자동차 회사가 신규 설계 개발중인 차는 전륜구동차로 밝혀지고 있으며 사용자의 전륜구동차에 대한 선호도는 계속 크게 증가할 것으로 보인다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.11
• /
• pp.1319-1326
• /
• 2012

This study focuses on the influence of tractive forces on the self-stability of a bicycle. The eigen-value analysis of the self-stability of a passive rider control linear bicycle model can be used to analyze the self-stability. A linear bicycle model with front and rear driving forces is developed. The influence of tractive forces on the self-stability is identified by using the developed model. A nonlinear multi-body bicycle model is used to confirm the results of the linear analysis.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.6
• /
• pp.248-257
• /
• 1999

A mathematical model was developed to investigate the mechanical interrelation between soil characteristics and main design factors of a tracked vehicles , and predict the tractive performance of the tracked vehicles. Based on the mathematical model, a computer simulation program(TPPMTV98) was developed in this study. The effectiveness of the developed model was verified by comparing the predicted drawbar pulls using TPPMTV98 with measured ones from traction tests with a tracked vehicle reconstructed for test in loam soil with moisture content of 18.92%(d.b). The drawbar pulls measured by the TPPMTV98 were well matched to the measured ones. Such results implied that the model developed in this study could estimate the drawbar pulls well at various soil conditions , and would be very useful as a simulation tool for designing a tracked vehicle and predicting its tractive performance.

• Journal of Biosystems Engineering
• /
• v.23 no.3
• /
• pp.219-228
• /
• 1998

This study was conducted to develop the mathematical model and computer simulation program(TPPMTV98) for predicting the tractive performance of tracked vehicles. It takes into account major design parameters of the vehicle as well as the pressure-sinkage and shearing characteristics of the soil, and the response of the soil to repetitive loading. Structural analysis and numerical iterative method were used for the derivation of mathematical model. The simulatiom model TPPMTV98 can predict the ground pressure distribution and the shear stress under a track, the motion resistance, the tractive effort and the drawbar pull of the vehicles as functions of slip. Predicted tractive performance results obtained by the simulation model were validated by comparing the results firm the Wong's model, the offectiveness of Wong's model validated by many of the experiment. It was found that there is fairy close agreement between the prediction by TPPMTV98 and the results from Wong's model. The computer simulation model TPPMTV98 can be used for the optimization of tracked vehicle design or for the evaluation of vehicle candidates for a given mission and environment.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.1
• /
• pp.65-70
• /
• 2014

An Integrated Dynamics Control system with four wheel Steering (IDCS) is proposed and analysed in this study. It integrates and controls steer angle of front and rear wheel simultaneously to enhance lateral stability and steerability. An active front steer (AFS) system and an active rear steer (ARS) system are also developed to compare their performances. The systems are evaluated during brake maneuver and several road conditions are used to test the performances. The results showed that IDCS vehicle follows the reference yaw rate and reduces side slip angle very well. AFS and ARS vehicles track the reference yaw rate but they can not reduce side slip angle. On split-${\mu}$ road, IDCS controller forces the vehicle to go straight ahead but AFS and ARS vehicles show lateral deviation from centerline.

• Proceedings of the KAIS Fall Conference
• /
• 2011.12b
• /
• pp.507-510
• /
• 2011

착륙장치는 완충장치를 이용하여 항공기 착륙 시의 충격을 흡수하는 역할을 한다. 군용 헬기를 비롯한 일부 항공기에서는 비상 착륙시 탑승원의 생존성과 안전성을 향상시키기 위해, 착륙장치에 내추락 요구조건을 부여하기도 한다. 본 연구에서는 내추락 요구조건을 충족하는 다양한 착륙장치 설계 개념 가운데, 파손 장치를 이용한 전륜 착륙장치와 Blow-off 밸브를 이용한 주륜 착륙장치 설계를 제시하고, 성능해석을 통한 입증 과정을 소개한다.

• Journal of the Korean Society for Railway
• /
• v.5 no.1
• /
• pp.18-25
• /
• 2002

This paper is to study a comparison of ride stabilities for the guideway vehicle between its three primary steering types; the front-rear wheel steering type, tile independent wheel steering and the front wheel steering. A numerical model were built to investigate various factors to have an influence on the vehicular stability. It was shown that dynamic stabilities of the three types were dependent on the steering gain ratio of front wheel steering to rear. The front-rear wheel steering type was more stable for the value of positive steering gains and the shorter distance between front axle and guide link showed better stabilities. On the contrary, the independent wheel steering was more stable for the value of negative gains and the longer distance between front axle and guide link showed better stabilities. Ride characteristics of he front wheel steering seemed to be found midway. Ride behaviors due to time delay from front steering to rear were very different from steering type to type.