• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.5
• /
• pp.777-784
• /
• 2016

In this paper, the performance design and analysis for an Interior Permanent-Magnet Synchronous Motor (IPMSM) that will be used as a traction motor in the e-4WD system of hybrid SUV(Sports Utility Vehicle) and RV(Recreational Vehicle), are investigated using finite element method. In order to improve the accuracy of design, the tolerances of parts and assemblies as well as the material properties of permanent magnet, stator, rotor and winding etc. are considered under the conditions similar to real driving state of motor. Both no load performance test and maximum load performance test, in which real driving state and cooling condition have been considered, are also implemented via proto sample build to verify the validity of motor's performance design.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.1
• /
• pp.32-41
• /
• 1992

This paper presents a comprehensive study on the stability of several control schemes for the induction motor driven by current source inverters. A stator voltage controlled current source inverter drive system without a speed sensor is investigated in order to find appropriate control schemes, which are primarily based on direct or, alternatively, indirect frequency control scheme. It can be seen, especially that an introduction of the indirect frequency control method improves the inherent instability of the current source inverter drive system for the induction motor. The overall control systems with either voltage control loop or current and voltage control loops in addition to each frequency control scheme, are analyzed by utilizing the root locus method and simulated by computer to show the validity of this analysis.

• Proceedings of the KIEE Conference
• /
• 1999.07a
• /
• pp.73-75
• /
• 1999

The time harmonics of an inverter output voltage cause high frequency currents in the rotor bars of a squirrel cage induction motor, so that the harmonic copper loss density increases in the upper lesion of the bars. Such an higher loss density makes an nonuniform thermal source and deforms the bars due to the thermal stress. Therefore, in this paper, the copper loss distribution in the rotor bar of an inverter-fed induction motor, which is the source of the thermal stress, is analyzed by the time-stepping finite element method. As a result, the harmonic copper losses of 11 subregions in a bar are calculated and compared with those of sinusoidally fed induction motor.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.632-634
• /
• 2000

This paper presents a simple analysis method for inverter-fed induction motor using F.S.M and equivalent circuit. This analysis is carried out to analyze an induction motor driven by the sinusoidal voltage and the inverter. The results are verified by comparing with those of the time-step F.E.A and the experiment.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.690-692
• /
• 2000

In this paper voltage distribution in the windings of an inverter fed induction motor is studied. High frequency parameters of the induction motor are calculated using finite element analysis. With these parameters. a high frequency equivalent circuit of the inverter-cable-motor is formed. The transient analysis is performed using ATP-EMTP package to estimate the voltage distribution in the motor windings.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.9
• /
• pp.517-522
• /
• 1999

This paper addresses the issue of current sampling in a high performance AC drive system fed by a discontinuous PWM inverter. The effect of the sampling error due to the measurement delay produced by an input stage low pass filter and an A/D converter is described in the case of discontinuous PWM. To compensate for the sampling error, a method to estimate the delay time of the whole measurement system based on the measured current is proposed and its effectiveness is verified by experimental results. The proposed algorithm can automatically estimate the system delay introduced by the low pass filter and the A/D converter at the commissioning stage. By delaying the current sampling by the estimated value, experimental results indicate that more than 50% reduction of current ripple can be achieved.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.1057-1059
• /
• 2003

This paper presents drive analysis of slotless air-cored PM linear synchronous motor using two-dimensional analytical method. In order to calculate dynamic characteristic, back-EMF and linkage flux are calculated by Permanent Magnet Field and also inductance are given by slotless winding current coil. PMLSM drive simulation is performed by PI control system.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.744-746
• /
• 2003

This paper presents characteristics analysis of brushless DC motor(BLDCM) which is driven by four types of PWM mode. The Phase current, radial forte and torque ripples are generated differently at each PWM mode. So they have different influences on motor characteristics. In this paper, we analyzed characteristics of BLDCM using time-stepped voltage source finite element method. The effect of four types of PWM mode had been confirmed by comparing each phase current and torque ripple waveform. The compared simulation result is useful to select a better PWM mode.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.53 no.2
• /
• pp.51-57
• /
• 2004

Vector control schemes are used in inverter-fed induction motor drives to obtain high performance. Crucial to the success of the vector control scheme is the knowledge of the instantaneous position of the rotor flux. However, the position of the rotor flux change with temperature and magnetic saturation of the motor. This variation cause deterioration of both steady state and dynamic operation of the motor drives. Performance degradation is in the form of input-output torque nonlinearity and saturation of the motor. Analytic expressions are derived to evaluate the effects due to parameter sensitivity. Also, dynamic response is shown by speed command with the variation of stator and rotor resistance.

• Proceedings of the KIEE Conference
• /
• 2000.11b
• /
• pp.271-273
• /
• 2000

This paper presents the dynamic characteristics Linear DC Motor(LDM) using 3 Dimensional Equivalent Magnetic Circuit Network Method(3-D EMCN) by voltage driven. The movement of mover substitutes for the movement of magnetization in permanent magnet expressed by Fourier series. The Dynamic characteristics are carried out from coupling the electrical circuit equation and mechanical kinetic equation.