• Journal of the Korean Geotechnical Society
• /
• v.32 no.12
• /
• pp.79-91
• /
• 2016

Geosynthetic-reinforced and Pile-supported (GRPS) embankment method is widely used to construct structures on soft ground due to restraining residual settlement and their rapid construction. However, effect of cyclic loading has not been established although some countries suggest design methods through many studies. In this paper, cyclic loading tests were conducted to analyze dynamic load transfer characteristics of pile-supported embankment reinforced with geosynthetics. A series of 3 case full scale model tests which were non-reinforced, one-layer-reinforced, two-layer reinforced with geosynthetics were performed on piled embankments. In these series of tests, the height of embankment and pile spacing were selected according to EBGEO (2010) standard in Germany. As a result of the vertical load parts on the pile and on the geosynthetic reinforcement measured separately, cyclic loads transferred by only arching effect decreased with strength geosynthetic-reinforced case. However, final loads on the pile showed no differences among the cases. These results conflict with previous studies that reinforcement with geosynthetics increases transfer load concentrated on piles. In addition, it is observed that the load transferred to pile decreases at the beginning of cycle number due to reduction of arching effected by cyclic loading. Based on these results, transferred mechanism for cyclic load on GRPS system has been presented.

• Journal of the KSME
• /
• v.20 no.6
• /
• pp.442-447
• /
• 1980

내연기관에 있어서 connecting rod는 piston에 작용하는 가스압력과 관성력을 소단부로 부터 shaft를 거쳐 대단부를 통하여 Crankshaft에 전달하는 역할을 한다. 그러므로 기관의 운제중 끊 임없이 인장, 압축, 좌굴, 굽힘등의 하중을 반복하여 받기 때문에 이것에 견딜 충분한 강성을 지해야 한다. 그러나 일반적으로 connecting rod에 작용하는 하중과, 각부분에 나타나는 응력의 해석은 간단하지 않다. 왜냐하면 행정을 수행하는 동안 크랭크의 각 위치에 대하여 가스 압력 이나 관성력이 변하고, 또한 connecting rod 자체의 형상도 복잡하게 구성되기 때문이다. 따라서 보다 계산을 간단하게 하기 위하여 여기에서는 일단 connecting rod에 작용하는 하중은 최악조 건으로서 최대발압력 및 최대관성력을 적용하기로 하고, 계산결과에 따라 취약부위에 대한 은 력을 검토하기로 한다. 특히 대단부에 있어서는 cap을 연결하는 보울트가 불리면에 작용하는 하중을 충분히 견딜 수 있어야 하므로 보울트계산 또한 중요하나 여기서는 취급치 않고, 다만 이 계산에서 구한 하중을 사용하여 VDI 2230에 의한 방법으로 계산하면 될 것이다.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.21 no.3
• /
• pp.209-215
• /
• 2009

A new load surface method for reliability of caisson type breakwater was proposed. Linear functions for horizontal wave force and uplift force were estimated by using water level and wave height then they were applied to the reliability analysis of breakwater using first order reliability method(FORM). In the numerical example, sliding and overturning failure probability of caisson type breakwater were analyzed by using load surface and they were compared with those by Monte Carlo simulation.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.1416-1422
• /
• 2010

Monorail has been classified as straddled type and suspended type. However, Inchon Wolmi Eunha rail, a center guide type first ever introduced in the world, uses a new concept Y-Beam as guide rail. Since Y-Beam takes horizontal loads of monorail through guide wheels, it is an essential structure for the safe operation along with concrete surface and steel beam which take vertical loads through main tires. This study presents the characteristic and reliability of Y-Beam and Y-Beam fixture, clamp, which are not only taking horizontal loads but also guarantying both guiding and stability of monorail and holding power supply line.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.10a
• /
• pp.95-98
• /
• 2001

Co-cured joining method is an efficient joining technique because both curing and bonding processes for the composite structures can be achieved simultaneously. It requires neither an adhesive nor a surface treatment of the composite adherend because the excess resin, which is extracted from composite materials during consolidation, accomplishes the co-cured joining process. In this paper, we considered three bond parameters, affecting tensile load bearing capacity of the co-cured single and double lap joints. Filially, we nave presented optimal bonding conditions for co-cured single and double lap joints with steel and composite adherends under tensile loads.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.125-133
• /
• 2002

In this study, it was investigated about endurance limit and fatigue behavior of load carrying fillet welded cruciform joints according to welding methods of SMAW, SAW, MIG and FCAW commonly using for welding structures in present. Endurance limit carried omit highly in the order of SMAW, MIG, SAW, FCAW and fatigue crack propagation ratio carried out lowly in the order of SMAW, MIG, FCAW, SAW. By these results, it is needed to use SMAW or MIG welding methods for welding structures with small welding capacity and SAW or FCAW methods for large welding structures after due consideration about economic gains and operation efficiency of welding. Fatigue crack propagation ratio is more effected by strength of welding materials than endurance limit of welding materials according to welding methods.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.12 no.1
• /
• pp.38-44
• /
• 2003

In this study, endurance limit and fatigue behavior of load carrying fillet welded cruciform joints depending on commonly used welding methods such as SMAW, SAW, MIG and FCAW are investigated. In respect of endurance limit SMAW specimen showes highest result, and then MIG, SAW, FCAW in descending order. However, SMAW specimen showes lowest crack growth rate and it followed by MIG, FCAW, SAW. By these results, it is needed to use SMAW or MIG welding methods for welding structures with small welding capacity and SAW or FCAW methods for large welding structures with respect to economic benefits and operation efficiency of welding. It was also shown fatigue crack growth rate was more influenced by the strenght of welding materials than the endurance limit of welding materials.

• Journal of Auto-vehicle Safety Association
• /
• v.5 no.1
• /
• pp.50-55
• /
• 2013

When it comes to commercial vehicles, their unique characteristics - center of gravity, size, weight distribution - make them particularly vulnerable to rollover. On top of that, conventional heavy vehicle brake exhibits longer actuation delays caused in part by long air lines from brake pedal to tires. This paper describes rollover prevention algorithm that copes with the characteristics of commercial vehicles. In regard of compensating for high actuating delay, predicted rollover index with short preview time has been designed. Moreover, predicted rollover index with longer preview time has been calculated by using road curvature information based on environment information. When rollover index becomes larger than specific threshold value, desired braking force is calculated in order to decrease the index. At the same time, braking force is distributed to each tire to make yaw rate track desired value.

• Journal of Korean Society of Steel Construction
• /
• v.24 no.5
• /
• pp.559-569
• /
• 2012

Cross-beam in the existing temporary bridge system is usually installed to prevent the lateral-torsional buckling of girders and to promote the construction efficiency. However, most of this cross-beams are connected to the girder web by bolts, and therefore, gravitational load resisting capacity of the cross-beams are negligibly small. In recent years, new temporary bridge system, in which the cross-beams and girders are connected to resist the external loads as a unit, was developed. In this paper, we present the experimental and analytical study results pertaining to the structural behavior and load carrying capacity of new temporary bridge system. From the results of study, it was found that the continuous cross-beam increased the flexural rigidity and reduced the maximum flexural stress in the girder. In addition, it was also found that the new temporary bridge system developed is more appropriate for the application in the long-span temporary bridge.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.18 no.2_spc
• /
• pp.275-289
• /
• 2020

In 2017, multimodal transportation tests for evaluating road, sea, and rail transport were performed by research institutes in the US, Spain, and the Republic of Korea. In this study, acceleration and strain data determined through road and sea tests were analyzed. It was investigated whether the load generated for each transport mode was amplified or attenuated according to the load transfer path. From the results, it was confirmed that the load transfer characteristics differed according to the transportation mode and loading path. The effects of strain determined through each test on the structural integrity of the spent nuclear fuel were also investigated. It was found that the magnitude of the measured strain had a negligible effect on the structural integrity of the spent nuclear fuel, considering its fatigue strength. The results for the acceleration and strain data analyses obtained in this study will be useful for scheduled domestic transportation tests under normal transport conditions.